Prime stable at 2700 (300x9) on stock voltage and stock air cooler on a MSI K8 Neo 2.
Printable View
Prime stable at 2700 (300x9) on stock voltage and stock air cooler on a MSI K8 Neo 2.
Where is it from?
my week 47 3200 wouldnt do 2.55 at any voltage.
2.7ghz...stock...everything...:eek:...dang thats nice. These newer Winchesters just keep getting faster and faster...:D
jjcom
If you had tccd ram and a good ondie controller, 270x10 would really fly! I should get one of those if my 3000+ has a crappy ondie controller and venice doesnt come soon or cheap enough ill just get a 3200+ then
ugh..my week 44 3200..really sucks then...2550 and requires 1.55v idle/1.58v load..
man I never get lucky when I buy a cpu hoping to overclock
thats not so bad, mine does 2.6GHz at 1.52v but more volts dont help and it doesnt go higher. Its an older week so I guess I did luck out, yours is probably average but not bad
haha I know the feeling!Quote:
Originally Posted by nealh
Quote:
Originally Posted by jjcom
Unfortunately it's not that easy - to pickup a week 48 and hit 2.7 Ghz. Posts here can be misleading. I've gone through 6 winnies now and the one in my sig was the only one that OC'd worth a sh1T.
dnottis
You've gone through 6 NEW winnies?
Haha yes, 2 x 3500's (just too expensive), 3 x 3200's, 1 x 3000's. I have 1 3000+ in here and one of the 3200s in my wifes PC. Sold the rest and one 3500+ was RMA'd for not Priming stable at stock.Quote:
Originally Posted by IvanAndreevich
yeah I know...I've seen the posts with people who end up buying many winchesters before finding the good one, or just feel Afraid wife/girlfriend will kick them out after seeing credit card bill lol :DQuote:
Originally Posted by dnottis
jjcom
hahaha! :)Quote:
Originally Posted by jjcom
same hereQuote:
Originally Posted by dnottis
0447SPAW
I got it with the mobo from Monarch. I bought the retail cpu. I havent even bothered going higher yet as my gskill isnt here yet and i havent put on water yet. I may just leave it on the stock heatsink as I'm happy with 2.7
if your winchester is a 3200+, would it not be x10 (not x9)?Quote:
Originally Posted by Franky 4 Finger
You can adjust to lower multi's.. only the higher multi's are locked IIRC (i.e. 11x, 12x, etc..)
dnottis
By new I meant after week 41. List the weeks of the chips you went through, will ya?
Hmmm - when you say the didn't OC worth a sh1T - can you tell me what you mean? Like they won't hit 2.5? 2.6?Quote:
Originally Posted by dnottis
I was thinking about picking up another 3000+ to see if I could squeeze out a few more mhz - (running at 2.6 24/7 right now) - but maybe I'll just be happy with what I got...
I went 300x9 becuase my corsair xls cannot really run over 200. By using 300 FSB I can run my mem at 200. BTW, 280x10 wasnt stable on stock voltage.
Can you do a superpi run on 9x300 plz?Quote:
Originally Posted by Franky 4 Finger
thx
Ok. Not sure if this worked. Score sucks because I am in single channel with no OC on the memory.
Nice chip...
With dc and small oc on mem u should get like ~ 30-31s.
if i rma because dont oc's nothing, but getting an excuse that isnt stable at stock speeds, will they trade for a new one??Quote:
Originally Posted by dnottis
Its an 0448SPBW
Oh sorry - I dont recall all the weeksQuote:
Originally Posted by IvanAndreevich
the ones I still have are 3200 wk 41 (max 2.5), 3000 week 41 (max 2.6) and 3200 week 47 (max 2.5).
Most of them wouldn't do 2.4 regardless of voltage and 2 of them were 3500's! I also would consider a bad overclocker something that needs 1.6 to hit 2.5 stable. Like a few of the ones Ive had. My best OCer does 2.6 @ 1.55 +5%, and 2.5 @ stock volts. The other CPUs I still have need 1.55 + 8.3% just to hit 2.5Ghz. I see people here getting 2.6 or 2.7 on stock volts. I've never been that lucky.Quote:
Originally Posted by MUCHO
Yea the 3000 in my sig came from Monarch. Monarch's CPU have overclocked much better than the ones I got from Newegg...maybe I'll try another one from Monarch soon. Tired of buying these things to get a crappy overclock.Quote:
Originally Posted by Franky 4 Finger
Check this out. On water 290x10. Havent tested prime yet
dnotis, have you tried this??Quote:
if i rma because dont oc's nothing, but getting an excuse that isnt stable at stock speeds, will they trade for a new one??Quote:
Originally Posted by dnottis
3ghz but not stable. Looks like it will take more voltage to break 3. I'm priming at 2.9 to see how stable that is.
My week 41 3200+ craps out ~2.55 also :dammit:Quote:
Originally Posted by dnottis
hehe mine refuse to go over 230fsb :) doesnt matter what multipler i use :)
gonna go home and check what week it is. but its week 20-30 smth :)
crappy clawhammer
you got the full 3 lines of code on it? no one really lists the 5 letters anymore, and i'm wondering if there is anything to them, but also the last 4 numbers on 3rd line.
Thats owesome, dare disclose what kind of timings you have in your bios??? :slobber:Quote:
Originally Posted by Franky 4 Finger
sweet stuff, my week 43 does 2550 @ less than stock volts, i plan to run it 2400 Mhz @ 1.344 24/7, as it does that quite well (mobo undervolts a bit, in reality it goes from 1.328-1.344) i think its a 2700Mhz easy chip, will have to wait till my ram gets here to tell. yea tccd!
i didnt take a picture and i just setup the watercooling. how high can/should i run it on water. i planned on abusing this chip but it seems too good for that.
f**k it up man :p
my personal opinion is newcastles/clawhammers etc could all take 1.9-2v and there is zer o evidence that killed them, my personal guestimate is a winchester will have zero issues running at 1.9v, and if you want to be safe try say 1.8-1.85v, this is if you want to vcore mod, or have a board with higher voltage(don't think there are any before dfi is out).
when you do change anything and get a chance, if you remember have a look, i've always had cores with last 4 numbers being lower have done better, with sub 0100 numbers doing very well, and i'd suspect yours is deffo a low number.
my friend also recently bought one from monarch and is running at 2.6 stock. He hasnt tried higher yet because he likes running his memory 1:1. I may go order another one from them soon.
Quote:
Originally Posted by Franky 4 Finger
These are retail or OEM? Is this his a 3000 or 3200?
I want 2.9Ghz :slobber:
we both bought retail 3200+ and ordered a little over a week ago
what memory timing are you running?
idleuser > read the first page ...
Franky > can you tell me your temps w/ your wc
Do the steppings really matter on the 3200s or is it just week? i just received a 0446 TPAW. Anyone else got one. Congrats on the overclock there, sweet!
Dave
this any good?
ADA3200DIK4BI
CBBHD 0450UPMW
week 50???shall i buy it?!"
already seen somewhereQuote:
Originally Posted by Th3__W00T_GuY__
ocinside.de and ocforums
Maybe chips from weeks with "7" are cursed...Quote:
Originally Posted by dnottis
Because Winchesters from week 37 sucked hard too! :p:
Running core center on the Neo 2, I load around 46-7 C on stock voltage and 55-7 C on 1.65V. My memory is either at or below 200mhz because it wont overclock and its just 1 512 stick. Gskill LE's will be here by tuesday. I'm not doing anything special in the bios. I am running version 1.4 that came with my board and have followed the tips in the Neo 2 thread. I'll have my friend post his results here as well
I dunno my week 44 3200 sucks too 2550 is max....
Quote:
Originally Posted by cpulloverclock
cant find it!
ADA3200DIK4BI
CBBHD 0450UPMW
good or bad :confused:
Sorry, people on this forum are notorious for not answering somebody' s questionQuote:
cant find it!
ADA3200DIK4BI
CBBHD 0450UPMW
good or bad
That stepping should be the "best", based on the premise that the later the week the more mature the 90nm process. But as you know very well, overcloking is a gamble, nobody will know unless you test it, I think it will be better......
Lemme correct you. That stepping should be the "newest"! (not the best) Overclocking is entirely dependent on LUCK - not stepping or week.Quote:
Originally Posted by mata2974
Having a fixed memory controller after week 46 (according to oc anyway) should give u some better luck though eh!
Dave
My week 37 3200+ maxes out at 2500 1.625Vcore
Just tried a week 47 3000+. The darn thing maxed out at about 2400 and would not do better at any Vcore...
Messed up my Windows too..... hahaha... Ghost time !
One thing I did notice was the heat. The 3000+ week 47 was much cooler than my 3200+ week 37 :toast: but that did not do it any good.
Quote:
Originally Posted by Feiticeira
Had a week47 that would need 1.65 just to hit 2.5. I dunno about the memory controller but the overclock sucked.
Here's another 3200+ 0448 SPBW from Monarch with the MSI Neo2 board. This is with the stock cooler at stock voltage.
Ram: 1 GB G.Skill "LE" kit.
PSU: PCP&C Turbocool 510.
Gskill is the :banana: :banana: :banana: :banana: :banana: :banana:
One more on stock voltage
Nice! :thumbsup: (Lucky Bastard.... :brick: )
Quote:
Originally Posted by TLAWS
retail or OEM?
Retail. Franky 4 Finger got his from Monarch also on the same day.Quote:
Originally Posted by dnottis
Ordered a 3000+ from Monarch today. We'll see how that one does......
Good luck. Did they provide you with the serial numbers/letters on the chip?
Didn't think to ask? (shrug) Just ordered the OEM chip via the internet
hhhmmm you tempted me with a new 3000 / 3200+ :p:
must have been unluckyQuote:
Originally Posted by Badge56
Just installed my 0447UPAW and it's been priming so far at 2430 a 1.4vcore with the default cooler