Get some OC results for 3d 03 and 05

Printable View

12-13-2004, 10:45 PM
Onepagebook

Get some OC results for 3d 03 and 05

Got some PMs wanna see some OC..
all done by water cooling :toast:

Official Reg

http://www.devilsword.com/ms7100/3dmark0511283.jpg

3d03...

Official Reg

http://www.devilsword.com/ms7100/3d0323599.jpg
12-13-2004, 10:47 PM
viccyran

Lol.. that's amazing. What kind of water is that?

:toast:
12-13-2004, 11:14 PM
Onepagebook

Quote:

Originally Posted by viccyran

Lol.. that's amazing. What kind of water is that?

:toast:

The water you can drink.. :p:
12-13-2004, 11:38 PM
viccyran

Haha you got a set of golden cards man..

490 on ambient water is crazy..

unless it isn't ambient :P :banana4:
12-13-2004, 11:42 PM
EnJoY

Could you give us more detail into this watercooling setup? Information like blocks used, tubing size, pump, rad...water temp...all would be nice. :)
12-13-2004, 11:48 PM
MaxxxRacer

opb was already getting high overclocks before the water. I think he was running over 450mhz. So its not surprise he get this high of an overclock on water. The part that really amazes me ins the memory.. wonder why nvidia seems to get the better memory compared to ati.

none the less, amazing results opb..
12-14-2004, 12:02 AM
blinky

Quote:

Originally Posted by MaxxxRacer

wonder why nvidia seems to get the better memory compared to ati.

they dont.

thats 680mhz, which is around what people get with ati cards (660-700)
12-14-2004, 12:02 AM
Onepagebook

Quote:

Originally Posted by EnJoY

Could you give us more detail into this watercooling setup? Information like blocks used, tubing size, pump, rad...water temp...all would be nice. :)

Actually, I purchased 2 DD nv68 water-blocks; unfortunately, the space between two sli on MSI 7100 is only .16 inches :stick:
which means you can only use one. see the pic below:
Not even can plug in:
http://www.e04hardware.com/barb6800.jpg
so how am I going to do? :confused:
Certainly I can think the other way to do that, so I use the DD RBX to see if the hole match! :banana:
Too bad, the 4 holes around 6800 gpu are too small, so the only way I can do is tie one hole.
Also I use 1 T and 2 Y fittings to finish all the setting with Eheim 1260( you definitely need that monster)
Below is the Pics.

http://www.devilsword.com/ms7100/watereniv6800a.jpg

http://www.devilsword.com/ms7100/watereniv6800b.jpg

http://www.devilsword.com/ms7100/watereniv6800c.jpg

hope it helps
12-14-2004, 12:05 AM
blass

holllyyyy ssh111T nice OC man!
12-14-2004, 12:12 AM
MaxxxRacer

ROFL!!! you used an rbx on teh vid card.. I have seen some ghetto stuff, but that is nuts man... nice work....
12-14-2004, 01:03 AM
quicksilverXP

Since you seem like you have ways of getting stuff... these http://snt-systems.com/catalog/produ...roducts_id=152 should do fine... provided you get them with straight fittings.
12-14-2004, 01:26 AM
Onepagebook

Quote:

Originally Posted by quicksilverXP

Since you seem like you have ways of getting stuff... these http://snt-systems.com/catalog/produ...roducts_id=152 should do fine... provided you get them with straight fittings.

Thanks dude, but I already use 1/2 fitting system :(
12-14-2004, 01:26 AM
MaxxxRacer

somehow i have a feeling that those aqua computer coolers dont work so well.. they sure do look pretty though... but they are almost entirly alluminum which isnt exactly so healty for your system.
12-14-2004, 04:29 AM
DGeNeRaT3

Anyone thinking Dual Phase change already? i know i am. UNBELIVEABLE scores in 3dmark2003 man :slobber:
12-14-2004, 10:03 AM
Onepagebook

Quote:

Originally Posted by DGeNeRaT3

Anyone thinking Dual Phase change already? i know i am. UNBELIVEABLE scores in 3dmark2003 man :slobber:

Discussed this with Chilly 1 already, but it's really hard to decide the size of block, hose and everything when you don't know the space between two video card. ;)
12-14-2004, 12:20 PM
DGeNeRaT3

yes this is true, but somehwhere i read about a guy makeing a "single slot" phase change block solution for his vapochill XE...basically the suctionline goes in the side, same as the water pipes would go into a swiftech GPU waterblock therefor, not taking up anymore space than the waterblocks you have on there now. I know for sure i am almost done my single stage system and as soon as i'm done it and prove it works, i am going to create a manafold and run 2 evaps from it. I want this setup and i want phasechange cooled GPU's! The reason i would like to do this is i can still cool the GPu's and CPU with subzero temps but STILL keep it all in one case like i have now.

I'll try and find that post where the guy created a single pci slot evap for his Vapochill XE.

DGeNeRaT3
12-14-2004, 12:55 PM
conrad.maranan

Congratulations on the #1 spots for 03 and 05, Kevin! :toast:
12-14-2004, 01:26 PM
G|-|oST

And the top of the Orb moves over to nVidia camp...

At least for a while.

Congrats on awesome results Onepagebook!!! :toast:
12-14-2004, 05:13 PM
spinboy

Yeah, that was really something!
How much Vdimm did you give the G.skills now again?
12-14-2004, 05:59 PM
megahurtz-oc

how cold is your water?
12-14-2004, 09:40 PM
Onepagebook

Thanks everyone,
1. my water? you know that weather these couple days..it's ohio!;)
2.Spinboy, 290? only use like 2.7, here is the one I use for 2.85v(MAX out)..:

http://www.e04hardware.com/670.jpg
12-14-2004, 10:39 PM
MaxxxRacer

*dreams of his winnie doing 300 on the memory* "poor little ocing b@astard
12-15-2004, 12:42 AM
Onepagebook

Quote:

Originally Posted by MaxxxRacer

*dreams of his winnie doing 300 on the memory* "poor little ocing b@astard

300? 300 is like way to low for me
12-15-2004, 01:02 AM
xs64

Quote:

Originally Posted by Onepagebook

Thanks everyone,
1. my water? you know that weather these couple days..it's ohio!;)
2.Spinboy, 290? only use like 2.7, here is the one I use for 2.85v(MAX out)..:

http://www.e04hardware.com/670.jpg

Is the performance of the NC is lower than the WC ??

I use my Adata @ 335Mhz x 8 timings 3-4-4-8 w/2.85v 1T and just got 7903 in mem bandwidth , the same setting with you Onepagebook ? Why ?? :confused:

I doubt that my NC is bad :(
12-15-2004, 03:02 AM
Rippthrough

Can you not get hold of some 90* barbs for that water block? Ok it'll slow the flow rate very slightly but they might fit then? Either that or dremel it into sections and weld it back together so you get a curve.
12-15-2004, 06:53 AM
H2OGun

Quote:

Originally Posted by Rippthrough

Can you not get hold of some 90* barbs for that water block? Ok it'll slow the flow rate very slightly but they might fit then? Either that or dremel it into sections and weld it back together so you get a curve.

My thought exactly. 45° is probably more pump-friendly but not sure if it can fit in there in such a small gap. It seems Asus A8N-SLI has better space in between.

http://www.anti-x.org/bbs/attachment..._SLI-Block.jpg
12-15-2004, 03:37 PM
Onepagebook

Quote:

Originally Posted by Rippthrough

Can you not get hold of some 90* barbs for that water block? Ok it'll slow the flow rate very slightly but they might fit then? Either that or dremel it into sections and weld it back together so you get a curve.

I don't think that could be done by elbow barb. you can install one of them , but when you spin the other one it will hit the one you insert already. :(
12-15-2004, 04:39 PM
IvanAndreevich

The ASUS board DEFINETELY much nicer in terms of space.. when you getting one, OPB?
12-15-2004, 04:58 PM
Onepagebook

Quote:

Originally Posted by IvanAndreevich

The ASUS board DEFINETELY much nicer in terms of space.. when you getting one, OPB?

Actually, Asus a8n SLI delux has been Messed Up, won't say anymore, get rid of that if you can :banana:
I will got my DFI around new year date or earlier, stay tune.
12-15-2004, 05:11 PM
H2OGun

Quote:

Originally Posted by Onepagebook

I don't think that could be done by elbow barb. you can install one of them , but when you spin the other one it will hit the one you insert already. :(

You can probably find one with swivelling head - not the plastic one, no? The picture I posted above has swiveling head quickfit so it is possible to install in tight space.
12-15-2004, 05:31 PM
esdee

Quote:

Originally Posted by Onepagebook

I will got my DFI around new year date or earlier, stay tune.

i hate you(j/k)

keep us update as always! ;)
12-15-2004, 06:19 PM
IvanAndreevich

>>Actually, Asus a8n SLI delux has been Messed Up, won't say anymore, get rid of that if you can

Don't have one, but buddy wanted to buy it. I'll advise him against it for know then ;)

>>I will got my DFI around new year date or earlier, stay tune.
The question is - can you break 25K 03? :D
12-16-2004, 02:01 AM
Onepagebook

Quote:

Originally Posted by IvanAndreevich

>>Actually, Asus a8n SLI delux has been Messed Up, won't say anymore, get rid of that if you can

Don't have one, but buddy wanted to buy it. I'll advise him against it for know then ;)

>>I will got my DFI around new year date or earlier, stay tune.
The question is - can you break 25K 03? :D

If i got Chilly 1's cascade running on my fx55 for 3.5g, it might be the chance...might be.. :D
01-15-2005, 02:46 AM
Malmedahl

Does anyone have any information about how big the space is between the cards on Asus A8n-sli DLX?
01-15-2005, 05:28 AM
Klosti

5 cm so 1.9685 inches
01-15-2005, 06:48 AM
eva2000

onepage maybe this is what you need http://www.xtremesystems.org/forums/...ad.php?t=50423 ? :)

is that water in the tube a bit murky there hehe
01-16-2005, 09:16 PM
marky

lol, swiveling head 90 degree barb? why?

heres a thought, just tighten 2 x 45 elbows in sync at the same time. should have room to turn?

:p: :toast:

All times are GMT -8. The time now is 01:25 AM.

XtremeSystems