Printable View
I wish I could go more into it, but we're ready to go out for the night. So, I'll just leave a WCPUID shot of the highest I could get her so far(locked yet)...
This is my 4th 1600+ and I must say I'm very pleased so far :)
http://ftp.teamslo.com/imup/n8s1400AGOIAat2100.gif
BBL w/ further test results :)
:eek:
OMFG..... what's the stepping and the week is it again?
This is too good to be true... 200SB with locked CPU?!
Is it stable? what's the temp with which sink?
N8,
Thats ecxellent!!
What type of Air cooler do you have??
OPP
Holy s_ _t man thats a golden cpu . I wonder how much you could get out of it on water and 2.3v or even better a prometia. :eek:
That might be one of those rare 2.20GHz to 2.30GHz Palominos with vapor compression. :)
DaGoochMeister,
How far was your 1600 doing with the Prometeia??
OPP
The best I can do with the XP1600+ that I have with 2.10V and running Prime 95 for 24 hours is:
good lord, nice OC's .
You both cheat! especially you gooch :toast:
N8 that is freakin awesome man!!!!
There are some over at OCAU that would be very very jealous fo you dood....:banana:
CONGRATS :toast:
Good to see you here Machiavelli! Cheat? You should know me better than that! :)Quote:
Originally posted by Machiavelli
good lord, nice OC's .
You both cheat! especially you gooch :toast:
Yea, it is the first chip I've recevied to whoop up on my very first 1600+(the AROIA that is my avatar). It is cooled by a Thermalright AX-7 & Vantec Tornado.
Just got back from the bar so I doubt I'll make much sense here :)
Its a AGOIA 0213 Y, and I have another AGOIA 0213 Y also that won't even match my AROIA, let alone this AGOIA.
This is not a stable speed....yet. I will be happy if I can run 3DMark @ or above 2GHz :) Right now my AROIA runs 3D @ 1.9GHz pretty much flawlessly. I'm not even sure that its not my Samsung holding me back at this point as the 2815 BIOS for the 8K3A seems rather hard on the memory.
A month or so ago I bought H2O equipment...just been too busy till recently to play with it. This chip may be the motivation I needed in that department ;)
As for the temp, I don't know...no time to stress test @ this speed. All I know is that it was stable @ 1.85GHz @ default vcore, and 1.9GHz @ 1.85vcore. I can tell u what the temp was when i took that pic...about 27c w/ halt-cooling enabled, idle of course :P
Bad part is, I get about an hour to play with this chip, then I'm drug to the bar, and to top it off I'm leaving on vacation till monday...so no more playing till then! I will report back my further findings ;)
[N8],
that is one super OC! Congrats :toast:
Chong
[N8]
WOW, that's awesome. WHY did I go with xp2200??????????????
Save a hundred bucks and go FASTER!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
F&S
{N8} i have a new agoia-y 0213 1600+ here also. I bought two from newegg during the craze the aroia-y i currently use runs at 1970mhz prime95 stable and will bench 3dmark alnight at 2ghz+ giving me some killer scores... I use the slk-800+80mm 75cfm fan also my aroia does 1.85ghz at default voltage prime stable but takes 2.04v to hit 2ghz on air. withh some h20 or vapor this chip could do 2100mhz+, now Im thinking about trying the agoia thats sitting here:confused:
Congrats [N8] :D
When I receive my AX7 I'll be doing some testing with my AROIAY, too.
And here I am struggling to get my new agoia y 0213 XP2000+ past 1.95ghz :(
Guess as well as my new western dig hard-drive I'll be fitting a 1600 tonight too... which also happens to be an agoia y 0213... bizarre!
Awesome:)
Nice o/c ... in fact that's incredible :)
My 1600+ agoia y chip will only run 1.800 @ 1.75 not voltage nor a cold michigan night has gotten me to 1.900 :-/ \Ii'm quite Frustrated by my system and the instability the radeon has slapped on me.
I'm holding my breath... I had to RMA my epox 8k3a+ and haven't had a chance to check out my AGOIA 'Y'. God I hope I get as good results with my Thermalright SLK800!
my slk-800+aroia-y 2ghz also im trying my agoia-y 0213 new 1600+ right now.. Ill post some screenys.. anyone know where i can get web space that allows file leeching for pics
Send IFMU a pm he may be able to help you.
OMFG! you clocked it to 200fsb locked on air? holy schmoley. my 1700+ will do so far 11x170 locked, haven't really pushed it yet, but your overclock is simply insane:eek:
That's pretty good dude. Congrats.:toast:
Heres one of mine at that level.
http://www.bigbutton.com.au/~lord/XP...0fsbWCPUID.jpg
www.imahosting.com click on the sig uploaderQuote:
Originally posted by qwerty57
my slk-800+aroia-y 2ghz also im trying my agoia-y 0213 new 1600+ right now.. Ill post some screenys.. anyone know where i can get web space that allows file leeching for pics
That is Insane dood nice OC there and one bad ass chip
http://www.vr-zone.com/cgi-bin/vb/im...ilies/eek2.gif
Good job :)
Very nice overclock, n8...
So, actually what was the Vcore you had on that chip for the 2100 MHz run?
By the way, what is the color of the CPU's board? Green ou Brown?
N8:)
Sorry I'm late to the party my friend but that is a killer O/C you've attained on that 1600+:toast: Congrats my friend !
Randi:D
Morcego_Pt,
2.2v...and this was only during some quick testing before my vacation. I'll be interested to see what the max speed for 3dmark will be, as this chip acts quite different from my AROIA. Doubt i will have the time tonight, but I will be checkin it out soon :)
And thanks to the rest of ya'll! :D
Just curious... what does the sisoft CPU benchmarks compair with at 1900mhz?
LBJGH,
I'm not sure I understand what you're asking :)
In sandra when you run the cpu bench what processors does your machine come close to.
I prolly won't be runnin sandra again till after I pull it, snap some pics of the core, and unlock the thing. When I get up around 200FSB its hard to tell if instability is caused by the CPU or my Samsung PC2700. I'll report back after its unlocked.
MY LORD!!! :eek: You got that high and im stuck at 170(locked) cause Win98 keeps dieing on me at anything above it. Can you help. Refer to my sig for computer components. Im presently running at default vcore and the ram is running at an increase of .1 voltage. Im willing to try anything to get to those levels. Oh an AWESOME OVERCLOCK!!!! GOOD JOB!!!
Alphawolf829, Welcome to the Forum.:toast:
Thanks. :) Im looking foward to learning from here and overclocking to the max. :toast: :D
Alphawolf829,
There are prolly 4 things that could help you get higher right now:
1) More vcore...if your cooling can handle it.
2) More vmem...if your memory can handle it, which that Corsair "should" be able to.
3) Relaxed memory timings to rule out your memory holding you back right now.
4) Unlock you CPU...makes OC'n these AMD's just that much easier.
As I said before, I will be happy if this thing runs 3D stable @ 2ghz or above, but I won't know untill I unlock it and do further testing. You have a 1/5 divider w/ that mobo so I'd guess that none of you PCI devices are holding you back right now, as you're barely out of spec. Good luck! :)
Edit: My bad, welcome to Xtreme :D
well I have already tried the ram on the "fastest" speed at 2.7 and the CPU with a Vcore of 1.8 but window still died(I didn't go any higher with the voltages or any lower with the ram timings. For the amount of times I tried though I almost have the WIN98 Product Key memorized. Hmmm... Im running 170 currently but when I was at standard vmem it took longer to load, but when I increased it by .1 it loads normally again. I don't know what this means exactly.
Hmm, well for now I would highly recommend unlocking that CPU :)
It makes finding your max stable CPU OC so much easier ;)
Thanks. I'll unlock it eventually.:(
I won't lie ;)
I found it to be a major pain in the arse...but well worth it :)
Hmmm... Is my problem that my clock speed got to high for the HDD or is it the FSB? I would like to know so that when I do unlock it I know whether or not to lower the multiplier and raise the FSB, or raise the Multiplier and leave the FSB.
I would up the mult and lower the FSB then work back up again. If u snag at 170 again, up the mult again :)
I agree it's a pain in the ass unlocking an AthlonXP and it may be worth it depending on which model you are playing with.
I just unlocked my 1600+ and wonder if it was really necessary. The default multiplier is 10.5x and by raising the fsb to 166mhz I was able to run the chip at 1750mhz at the default voltage. I might be able to run 180mhz fsb which would give me approximately 1900mhz without changing the multiplier.
I guess the advantage to changing the multiplier is that I can use 166mhz fsb (maintaining default pci/agp speeds) and run the chip at 1916mhz. If the system is unstable with the default agp/pci then I know it's the CPU that can't cut it.
Quote:
Originally posted by [N8]
I won't lie ;)
I found it to be a major pain in the arse...but well worth it :)
Hehe...yea, there are times you will find you will end up runnin the default mult anyway...but, when you hit a wall, and you don't have another unlocked chip to test your max FSB, its nice to be able to play with the mult/fsb rather than just uppin the FSB...like if your ram is holdin ya back, or ya wanna run say 166fsb to keep your devices in spec :)
I've actually had my memory up to 190mhz but had to use more conservative memory timing. I can run up to 170mhz at cas2.
I like to keep the pci/agp within spec so that I can determine what the CHIP will do before I add fsb to the equation.
Quote:
Originally posted by [N8]
...like if your ram is holdin ya back, or ya wanna run say 166fsb to keep your devices in spec :)
Any update on this? I am keen to see the prime95 stable speeds @ default, 1.85v, and 2.15v. :)
Me too, but I actually haven't pulled the CPU back out yet to unlock it due to a couple reasons. Very tuff times at work this week exhausting me...and, I have my 3 rigs folding for the team because of all the talk of hotmail on our arse :)
I will prolly do 1.85v & 2.2v...if my cooling can hang w/ 2.2v and prime. I ran my aroia @ 1900 w/ 2.2v and got around ok, but i never put it thru prime or anything w/ constant stress like that(i.e. folding).
So, right now she is sitting @ only 166FSB, default voltage, folding away. Ain't even bothered to lower the vcore any, even tho @ 1750MHz I'm sure I can. I do know that its folded for a few days now w/o any sign of errors :P
Im back on aircooling at the moment, and the highest i can get my XP2000 is 1888 @ 1.85v Prime95 stable (spent the last few days priming, flasking, and folding, and shes as stable as a rock).
Not sure if i want to plug in the Vmod tho, and feed her 2v for an additional 100mhz tho :(
Hell I bought H2O equipment a few months ago and ain't even found the time to put it on. Not sure that its gonna get me anywhere further anyway, other than perhaps a few degrees drop in load temp, and a little quieter :)
If I can get this thing stable @ 2GHz w/ whatever cooling I end up using, I'll be extremely happy w/ the chip. 600MHz OC on a $50 chip...gd I love u AMD. :D
http://www.speakeasy.org/~rylandpage/0wnage.jpgQuote:
Kickass oc.
Well the motherboard I got from my RMA was an OLDER revision and it doesn't seem to maintain the voltage properly. But that said I was able to run Prime95 for a bit before the temps started to creep up too high for my liking (64C).
Quote:
Originally posted by Sinnah
Any update on this? I am keen to see the prime95 stable speeds @ default, 1.85v, and 2.15v. :)
LBJGH, i was keen on seeing N8's results :)
Next week I'll have my xp 1600+ AGOIA Y 0213 and couple it with some liquid cooling... looking for 2gigs smoothly, crossing fingers... :D
Ok, its been a while but the chip is out now and I think I got it unlocked last night...won't know till I put it in tonight and find out.
Put my AROIA back in and FINALLY set up my H2O(which I bought like 3 months ago and never had the time to install) and I've got it folding & stable @ 1950MHz, 2.2vcore, 42c load...50MHz higher than I could ever stabilize it on air.
So, I'll be pullin the AROIA tonight again and putting this AGOIA back in to see what speed it stabilizes at...something over 2GHz I'm hoping...just not sure how far over :)
Here is a pic i got of it before I unlocked it so u can see the full stepping:
Burning in right now @ 2000MHz...prolly let this go overnight...temps a little higher than expected...not sure if its that this chip runs hotter, if some air got in the lines, or if the AS3 has yet to burn in, or a combination of all 3, but I think this is more voltage than it will take to run this speed anyway so I will just let it burn in @ this overnight :) Oh yea, the unlock worked :D
Here's a quick screenshot b4 bed:
Good gawd. Aircooled... that's sick. :)
Watercooled now sys :)
P.S. Burn-in went fine overnight...not sure now if I'm gonna go for more MHz or less voltage...still deciding ;)
lord, What are the specs on your machine?
Just take my sig and substitute the AROIA chip for an AGOIA now :)
Very nice overclock, [N8] :) !
BTW with what PSU ???
Yeah, what PSU?? 4.97v on the 5v line at such high speeds is amazing!
Congrats for that 2Ghz chip ;)
Thanks :)
Antec 400W PP-412X w/ pots tweaked by urs truely :D
Congrats dood gr8 job :toast:
I wish my 1600+ would hit 2Ghz...it craps out at about 1.9Ghz no matter what I give it. :flame:
What HSF are you using on that dood?
Who?Quote:
Originally posted by Shroomer
What HSF are you using on that dood?
I'm using a Volcano 7+...works great for me. Idle temps are 35deg and load is around 39deg@1.9Ghz
I think you should check your sig
AGOIA ;)
sforza - thanks...wrote it in a hurry:D
Got an AGOIA Z in today and also AGOIA 41F. Gonna see what these puppies will do on air later today after finishing up a system. :)
Gooch:)
Hot damn my man...a "Z"......this may be interesting:D, but I am anxious to see if that "41F" lives up to my babies abilities.
Keep us posted on your progress my friend:)
Randi:D
MrIcee:
Oh yeah the 41F is a nice one even on air at 1.95V :) I wish I had more time this weekend.
Nice chip Gooch!
Well, I ended up @ 1.95v to stabilize @ 2000MHz & 39c temps right now folding. It passed prime at this speed for the 2 hrs that I ran it so I'm guessin its stable...time will tell...gaming usually fully tests my chips for me :)
Some time this week I will hafta check for max stable OC @ 2.2v & see what kinda temps I get to see if I wanna run that high. I just love my 2400++(second plus for 200MHz FSB :hehe: ) speeds @ $55 :D
Gooch,
I need to pop by and test a couple of those, better yet bring them by :D
OPP
Using an AGOIA F 0212 1600+ at stock multi and 1.85v on the core:
Here's a 1600 chip I'm running right now, it's week 9:D Not sure what stepping but it is a Y. Old but works well.
nice dude, what cooling and volts are on that chip?
Heres the highest I could get on water. (Note - 1.95 is the fastest stable)
http://www.xtremesystems.org/forums/...=&postid=43398
And heres the highest on air. (1.84 stable) Both 2.13 vcore.
Nice chips guys! Gotta love em :D
Such amazing chips. $50 for insane speeds. :D. I need to pelt mine to get anything more out of it. Lots of frustration was fought through to get this baby up to 2088. I have a duron 1.3 coming to play with though. :). I'm actually dissapointed in the clock speeds. I know my gigabyte mobo isn't helping, but I really was hoping to hit 2.1 with it. It just can't do it. :(. Ahhhh well. At least I'm at 2, and killing the P42.66. ;)
yup, $50 for a 2400+ chip :D
ExtremeAMD when u gonna hit 2.1 or 2.2ghz? I think a Pelt would do it.
Drozdov,Quote:
Originally posted by Drozdov
nice dude, what cooling and volts are on that chip?
That is with a Prometeia Evap Cooler at 2.1V, this chip wouldn't be to great without it.
OPP
Get a SLK 800 on there dood I bet that would get ya 1.95 to 2ghz easy. O ya and a tornado ;)Quote:
Originally posted by FUBAR
I'm using a Volcano 7+...works great for me. Idle temps are 35deg and load is around 39deg@1.9Ghz
Well, it does 3D @ 2023MHz flawlessly..having some problems above 2030MHz right now and I'm thinkin it might be these dern 40.52 drivers as I remember MrIcee having CPU OC problems w/ the 40.XX's too. Here's the compare:
http://service.madonion.com/compare?2k1=4851023
BTW, that score sux I know...got alot of tweaking to do yet...had to restore my bench partition and got a bit of work to do there :)
Hmm,Quote:
Originally posted by [N8]
Well, it does 3D @ 2023MHz flawlessly..having some problems above 2030MHz right now and I'm thinkin it might be these dern 40.52 drivers as I remember MrIcee having CPU OC problems w/ the 40.XX's too. Here's the compare:
http://service.madonion.com/compare?2k1=4845209
BTW, that score sux I know...got alot of tweaking to do yet...had to restore my bench partition and got a bit of work to do there :)
I think that we will see new ยน1 AXP+Ti4200 score soon :) :D ...
lol, I'm sure SKATAN & others will make me work for it :)