XP2000@2920mhz prime stable

Hi,

this is my new project. I reach 2920mhz with a T-Bred 1666mhz AIUHB 0316 MPMW. It maxes out @3045mhz. There I can make a Sandra bench. Further I don't testet it because the interesting thing is the stability.

The cooling is a selfmade compressor system with R404a and a Danfoss SC15D compressor which has 300W@ -40°C. I used a TEV for this thing. On 2920mhz @ 2,175V I have idle -15°C and load -8°C with CPU Disconnect function is off. With CPU Disconnect it is -23°Cin idle. The measuring is the CPU internal Diode! The Board is a old Abit KD7a. Yes I have also a NF7 but with this Board I reach only 2600mhz so this board suxx. I ordered now a MSI KT6-delta. Next week I try more.
All benches are on the KD7. The photos are on the NF7. More pics later.

http://people.freenet.de/benches/1.JPG
http://people.freenet.de/benches/2.JPG
http://people.freenet.de/benches/3.JPG
http://people.freenet.de/benches/4.JPG
http://people.freenet.de/benches/5.JPG
http://people.freenet.de/benches/6.JPG
http://people.freenet.de/benches/7.JPG
http://people.freenet.de/benches/8.JPG
http://people.freenet.de/benches/9.JPG
http://people.freenet.de/benches/10.JPG
http://people.freenet.de/benches/11.JPG
http://people.freenet.de/benches/cpuz_2920.jpg
http://people.freenet.de/benches/cpu_2_143x21.jpg
http://people.freenet.de/benches/pcmark3026.jpg
http://people.freenet.de/benches/mm2_143x21.jpg
http://people.freenet.de/benches/maxtemp.jpg

§§§§! Thats some xtream clock dude! Over 3ghz with an 2000+! con gratz man, burn it in a bit and get it primestable over 3g now ;)

believe me I try my best. Maybe with the new Mainboard!

nice score
what's the fsb?
that's alot of beer over there :D

Nice overclock.. Where did you overclock that processor , there seems to be a few people :)

Nice work.

.... how was the NF7 holding you back?

Thx.

Pops.

jau! noch n hamburger!
becks gold? hatten sie kein normales becks mehr? naja die richtige marke ists schonmal! :D

sehr fettes setup! wo hast du den radi her? ich hab vor auch n kompressor system zu bauen, kannst du mir eventuell helfen? wie hast du zb die blöcke gelötet? wenn du willst kann ich dir mein a7n8x ausleihen, kann bis 250fbs+ benchen und die caps und mosfets sind vom feinsten, werden kaum warm!

sorry, just excited to finally meet somebody from hh in this forum :D

nice score :banana:
achja duw würdest dich wundern wieviel deutsche hier sind ;)

:toast: now that's Xtreme!!

:slobber: wonderful clocks

Yeah! amd power! - could you pleas run superpi, and uploade the result? :slobber:

The good stuff ;) Very, very Xtreme..

hmm da mus sich mich auch mal wieder einloggn...auch wenn ich nicht mehr im "oc-genre" bin :rolleyes:
endlich mal wieder jemand der dt. land würdig vertritt hrhr ;D go on !... :D

Deutsche?? Wo??:D :D
Tja Diamond, ich kenn dein Sys ja schon von KM. trotzdem immer wieder beeindruckend! :slobber:

sieh an sieh an da kommen sie auf einmal aus allen löchern gekrochen ^^

damn nice chip, almost as good as my ex-1700+ :)

You did that on a KT400a? I knew I shouldn't have jumped off of the Via ship... Oh well, I'll go back to Via as soon as I get my new IDE card. I always seemed to have much better luck on Via chipsets than any other too. That's some xtreme clockin there...

EDIT
Nvm, reread the first post.

ok I upload some more pics today afternoon Superpi 1M or?
I know the fsb suxx because the don't do much more. The NF7 holding me back in the Vcore. 2500@1,85 stable, same frequency@2,00 Volt not stable, 2,1V bluescreen. And the higher the Vcore, the lower the fsb i have to set. So this Board really suxx. I tried the KD7 only because I wanted to see the real Temperature. I believed on the NF7 that my project suxx until I tried the other Board. That was luck I think.I had also the same chip as the JCviggen 0308 XPMW but that was not so good. Max.Vcore on this chip 2,06 V and with this I reached 2860Mhz. Not more. I think generally that the AIUHB chip's can go higher with the Vcore.

So nun für die Deutschen:

Nene ich komm net aus Hamburg, sondern aus der nähe von Nürnberg. Ich und mein Kumpel saufen das Zeuch ohne Ende. Geh mal auf www.dichtistpflicht.com da siehst es. Habt ihr vielleicht nocheinpaar Becksdosen bei euch??? Das wär echt korrekt

What month/week/stepping on the 2000+ ?

Mines 0318 SPDW DUT3C Y... Can pull 2600mhz on air with the right setup.

0316 MPMW DUT3C

@sayaa
Bist nicht der einzige hamburger.....;)

@Diamonddog
Wow, great oc!!!:toast: But: you really went to a lan with that setup?

DD

i don't go to lan's because the where I am is computer club and there is a lan 24/7/365

SuperPI is only 43s. I think that is the low fsb.

http://people.freenet.de/benches/fullload_2920.jpg

Nice OC...lots of volts though.:)

very nice OC there!
you got PM diamonddog! :)

Nice overclock! And a nice chip :)
Now whoop up that FSB :D

yes it is the fsb. i did 37sec with an xp1700@2866mhz @220mhz fsb

ok. my dfi ultry infinity and msi kt6-delta is ordered. We will see who will make the run :D

LOL nice one!

Quote:

---

Originally posted by diamonddog
ok. my dfi ultry infinity and msi kt6-delta is ordered. We will see who will make the run :D

---

NOT the DFI.

esp. if you get a made in China.

crapstick for CPU o/c:(

Quote:

---

Originally posted by diamonddog
SuperPI is only 43s. I think that is the low fsb.

---

Definatly low bacause of the fsb... just got a desent mobo that can handle the speed an then you can run some killer superpi :cool:

my barton 2500+@ 2541 (231*11) does 38 sec ;)

Grüße aus Leipzig,
echt klasse OC von dir :), nun noch den FSB anheben :D !

Na servas, das nenn ich an Radiator :D

Und natürlich an Mords-oc. :toast:
Sauf net so viel. :p:

Very nice oc.
Defeinitely want to see what happens on the DFI with more FSB.:D

Very impressive overclock...
Indeed, the nf7-s can be a pos... :(

Aber meiner Deutsch ist nicht so gut, erschuldigung...

great oc :toast:

<- München :)


X