Custom system work's

Just like thennvols 9 a building a simple phase -change system by reading thi's forum over and over agean.
De old metal man provided my black star (danfoss)fr6bxt2 unit
A couple of old compressors for vacuum also ,and a gif it a tray filled
with propane.

http://users.pandora.be/smolly/Phase...opstelling.JPG
The block
http://users.pandora.be/smolly/Phase...nge/slang3.JPG
The temp W O heatloud
http://users.pandora.be/smolly/Phase%20change/-50.JPG
Later on a filled the system again with de cpu on it,and do -24° on te block on my barton 2500+@ 2700 mhz
http://users.pandora.be/smolly/Phase...nge/pcrun1.JPG

Now a take it apart and try to make a better blok and integrade de captube in the suckline and a case and al the stuf .

Thank's for al the info provide'd here.and the warnings for the use of propane ,a tray to be extreme careful whi't this stuf and duble check al my brazzing and do nothing in the house untill am sure it is OK.

Sory for my bad englich also :(

Looks good :D How do you get the cap tube into the suction line?

looks like you need to work on your tuning of the system...your load/unloaded temps are a little distant from each other.

Quote:

---

Originally posted by afireinside
Looks good :D How do you get the cap tube into the suction line?

---

A make a new blok and insert de captube like bowman learn us;)

Insert it via a sea flair angle (don't know the name of it )

Nice system you have there. and a nice clock on the cpu too.

Quote:

---

Originally posted by bigpoppa
looks like you need to work on your tuning of the system...your load/unloaded temps are a little distant from each other.

---

Load temp = -22°C
unload temp = -30° (litle time idle)

The picture of -50 is not acurate ,bud de lowest temp a just had during the filling whi't to litle gas in it :D
The - 50° temp not stand any load ,it just was cool to take a pic of it ;)

Quote:

---

Originally posted by Pandrone
Nice system you have there. and a nice clock on the cpu too.

---

Yep ,my cpu is just fine ,a just play a litle and let the system idle down to -32°C and see hu fast it boot ,
Wel sundenly a had this schreen on my monitor :cool:

http://users.pandora.be/smolly/barton/cpuid3018.JPG

Bud the system could not hold the heat and shut of after 10 min or so.:mad:
Need to inprove the cooling a litle a think ;)

Grats :)

Nice work Smolly;)

nice job you need som r290 or r404 or r22 like i used:) but good job man

hey man i wanna say thanks for mention my system

Quote:

---

Originally posted by MickeyMouse
look slike sh*t dude ;)


nice stuff I likes It alot my man and that screen shot with r12 only "WOW" no words!! :)

---

Lol
The unit is an old R12 unit ,bud a filled it whith R290 (propane)
A think there is som confusion on this :p:

Made a new blok .
Ful handtool made and 1 long(40 cm) channel inside , going up en down in 9 channels a 9 mm .
Captube enters via the suction line ;)
archhh , lets tray :p:

http://users.pandora.be/smolly/Evap/evap1.JPG
http://users.pandora.be/smolly/Evap/evap2.JPG

Looks good, keep it up!

Evap working.

http://users.pandora.be/smolly/Evap/evap6.JPG

insulation

http://users.pandora.be/smolly/Evap/evap8.JPG

results: koper bar in water of 50°C blok hold -30 °C

http://users.pandora.be/smolly/Evap/evap9.JPG

no loud temp -52°C

http://users.pandora.be/smolly/Evap/evap7.JPG

Excellent work, congratulations. -52C even unloaded is quite an achievement. If you want to improve your loaded temps you should look for Armaflex insulation, it is denser than the insulation you have on now. Remember, insulate insulate insulate!

Do you have any more pictures of the inside of your block? I'm interested in how you made it.

Txs,Gkiing .

Oeps ice al over, 30 min later , water 12 °C blok -41°
Looks ok for now , time to play on cpu :slobber:

http://users.pandora.be/smolly/Evap/evap10.JPG





Paint , pfffff :D

http://users.pandora.be/smolly/Evap/evap%20plan.JPG

t'is is the principe. gas goes up en down and swits in up en down block ;)

Channel is D 9 mm +/- 40 CM long t'his way .

I take the danfos 1/5 hp compressor out and an embraco 1/3 hp LBP in .

http://users.pandora.be/smolly/Evap/evap11.JPG

after 7 min temp = -61 °C .
W'hat is wrong ? -61°C is not posible a think .( R290 )
It is a new temp probe , but it is not acurate i think .

if the vaccum is deep enough the boiling point can do that.

that would be a pretty strong vacuum

post what ur guages say on the suction line by the compressor

Quote:

---

Originally Posted by blinky

that would be a pretty strong vacuum

post what ur guages say on the suction line by the compressor

---

Big problem . I don't have a set or guages .
I don't know :(

very beautiful ^^

u dont have guages smolly?...lol, you should, i dunno seems like you dont need it, you tuned it pretty well!

I have gauges but no thermometer.. well I have a thermometer on my fluke voltmeter but it goes to -50 then goes blank.

Test a fluke thermometer on it , m meter is -60 °C and the fluke on -55.4 °C.

conclusion =+/-5 °C diferance .


An old LCD broken tempmeter has -54.7°C on it, so a use that in the future .

So a'm hapy for the moment , gona test on cpu ;)

very good work mate. I really like your system. Keep up the good work.