Custom Wood Case IV- Antique Zenith Radio Build - 24Nov2010
1930s Zenith 5-s-29
Here is a list of links that will take you directly to the threads where I have posted pictures in case you want to skip straight to the pics.
http://www.xtremesystems.org/forums/...8&postcount=22
http://www.xtremesystems.org/forums/...0&postcount=27
http://www.xtremesystems.org/forums/...1&postcount=32
http://www.xtremesystems.org/forums/...4&postcount=49
http://www.xtremesystems.org/forums/...3&postcount=61
http://www.xtremesystems.org/forums/...8&postcount=65
http://www.xtremesystems.org/forums/...8&postcount=88
http://www.xtremesystems.org/forums/...&postcount=102
http://www.xtremesystems.org/forums/...&postcount=107
http://www.xtremesystems.org/forums/...&postcount=114
Completed Pics
http://www.xtremesystems.org/forums/...&postcount=159
http://i5.photobucket.com/albums/y16...p/outside2.jpg
Introduction
As I enjoy the design and building process, I find myself again working on another custom wood case design. A few years ago, I became so disgruntled with cases not designed for watercooling that I decided to make my own case. Since I like to work with wood, this material was my natural choice. This case is my 4th custom case build.
There was a time in particular during the early 20th century when for several decades there was an emphasis on aesthetic quality and workmanship in furniture made for the home. This extended to the central electronic device of the era, namely the radio. My last case I modeled after many of the furniture and architectural designs of the early 20th century with the idea of building a custom watercooled case that would have fit the time period had it been built then.
For this build, I wanted to take things one step further by designing this case directly after a particular model of antique radio. Many radio collectors frequently collect radios built during the 1920s and 1930s because of their stylish appearances. I am not a radio collector in any way, but I do have an appreciation for the styling of many of these radios.
My plan is to build a performance minded system with a regular ATX MB with mid-sized tower dimensions. I want to reuse my current parts since they are only about 6 months old, and I currently don't want to spend the money yet on an I7 setup. I considered changing to a micro ATX MB, but given the proportions of the radios that I have researched, using a micro ATX MB offers me no real benefit as far as size goes.
I spent a lot of time researching and looking around at literally hundreds of antique radio pictures online. Many radios do not have a shape that can reasonably be replicated for use as a computer due to the space and placement constraints of components. It is also necessary to find really good pictures of a radio in order to be able to build a case after it. There are a number of radios that I could build after and like, but there simply aren't enough detailed photos of them to come up with a fairly accurate design.
MODELING
I have spent the last two months almost every day working in Sketchup modeling to the tune of probably 200+ hours (fortunately I have a lot of down time at work where I can use my laptop). This includes time I spent modeling several of the Bitspower rotary fittings
http://i5.photobucket.com/albums/y16...erFittings.jpg
which have been posted on the Sketchup Components Collection website. I was dealing a couple of pretty tight areas and wanted to have the fittings modeled to get an exact placement of components. I messed with every combination of placement using triple radiators I could think of.
http://i5.photobucket.com/albums/y16...ay09/ideas.jpg
I prefer using dual triple rads as I like a system to be as quiet as possible as well as being future proof. I also wanted the dimensions of this build to be smaller than my current case due to the way that it fits inside of my desk.
I spent a lot of time hashing out the placement of each component and the loop order of the setup down to every last detail I could think of. For example, I designed at least 5 different hard drive mounts alone. I do not like T-lines. I designed and redesigned the res to make it easily accessible for filling with the pump directly beneath it for good water supply to the pump. I have never spent anywhere near the amount of time designing a setup as I have this one.
DESIGN OPTIONS
The first radio design that I settled on was a 1935 Grunow 650 Tombstone radio.
http://i5.photobucket.com/albums/y16...w_650_1935.jpg
The dimensions and size fit what I was looking for. This model would require quite a bit of time and detailed routing due to the design. I completely modeled a design for this radio, and may build this in the future. However, in researching some more, I ran across the 1934-36 Zenith 5-S-29.
http://i5.photobucket.com/albums/y16...enith5s029.jpg
My daughter really likes the look of this radio (she likes the Grunow as well), which was one vote for sure in its favor, but I also found that I could get a replica radio dial, dial glass, escutcheon (dial bezel), and knobs for it. Since the Grunow wasn't as popular of a radio, parts are not available, so I drew the radio dial from a picture, would have to make my own knobs, and would have to make my own escutcheon (dial bezel). Buying the replica parts is costing me about $120, but it will add a very genuine look and feel to the case. My consultation team (wife and daughter) think that I should build them both, and I am entertaining the idea in the back of my mind. For the moment however I am just working on the Zenith design.
Base, DVD Mount, Dial Needles, Reservoir
Base
I added some cleats and mounted the base trim to the bottom piece. I screwed the base on instead of gluing as I want to be able to remove it should I need to make any adjustments to the DVD area later. My concern here is how well the slot loading DVD drive itself will hold up as I read mixed reports as to their reliability. I figure if I ever need to switch to a tray loading drive instead, I would want to be able to remove the base trim to adjust the front slot dimensions.
http://i5.photobucket.com/albums/y16...un09/base1.jpg
I made the mount for the DVD drive. This is made of one piece of 18 gauge aluminum that I bent using a bench vise, muscle, and hammering. I frankly wasn't expecting it to turn out the first time around, but it did. The drive is screwed into the mount.
http://i5.photobucket.com/albums/y16...un09/base2.jpg
http://i5.photobucket.com/albums/y16...un09/base3.jpg
In my design, I left an open area above the drive for the cables to come through. I cut two cleats, and cut a piece of smoked acrylic (still has paper on in pic) into which I will cut slots for the cables. I want to use the SATA drive adapter board for the DVD drive that I bought, but it extends about 1/4" below the drive which makes it stick out below the bottom trim. The IDE drive adapter sits flush with the drive bottom, so I may be stuck using the IDE adapter board that came with the drive instead.
http://i5.photobucket.com/albums/y16...un09/base4.jpg
http://i5.photobucket.com/albums/y16...un09/base5.jpg
Dial Needles and Mounting
I wasn't able to get original needles for the dial, so I made my own ones. I am very pleased with the way this has turned out. It took quite a bit of fiddling with this to make it work. I had a good front pic of the dial area of the case that I resized in Photoshop to the actual dial dimensions. I traced the "Z" needle onto a new layer in PS, printed that layer out, taped it onto carbon paper with blue painter's tape, and traced and cut out the pattern on some 1/8" smoked acrylic. I mistakenly painted the needles first before drilling the center hole, so I had to sand them back down and after fitting later repaint them. I also used a dremel and thinned out one of the needles to be less than 1/8" so that they would easily under the dial glass.
http://i5.photobucket.com/albums/y16...un09/dial1.jpg
I cut a circle larger than the hole area, mounted it to the backside, and drilled holes for 2 metal LCD mounts.
http://i5.photobucket.com/albums/y16...un09/dial3.jpg
There is a short piece of 3/8" dowel going between the back mount and the dial and needles so that the needles can be tightened into place without pulling back on the dial. I will fill in the slot on the screw with a bit of caulk and put a drop of white paint on it after it is mounted permanently so that the brass and screw slot aren't visible.
http://i5.photobucket.com/albums/y16...un09/dial2.jpg
This is with the hole dial in place to give you an idea of how it will look. The needles will of course be painted their respective white and red.
http://i5.photobucket.com/albums/y16...un09/dial4.jpg
Reservoir- Making One and a Guide
I haven't been very impressed with most of the commercially available reservoirs in my time watercooling. There are a few good ones, but with those of course you are limited to their layout and design. Especially since I have gotten into making my own cases the last few years, making my own reservoir to my own size/layout has worked well for me. I have tried and used T-lines before, and frankly I don't like them. I like the ease of bleeding and filling associated with my reservoir designs much better. So if you happen to hate reservoirs, I just say to each his own!
I wanted to take a bit of time to explain a bit more in depth how to make a reservoir should others be interested. I have yet to find a guide that tells how to do this. There are many ways to make reservoirs. Mine is only one way. But this way is what I have come up with over several years of trial and error that works for me and has proven 100% reliable. I capillary solvent weld cast acrylic together with no o-rings to keep the res watertight. This is a means of making a res that most do-it-yourselfers can manage with just plain hand power tools. If you have a better way to do this, by all means share your input as this is by no means an infallible guide.
Making your own res will probably cost you a bit more up front, and takes some time to get used to, but it gives you a flexibility in design and options that you simply cannot buy. Usually when I buy materials to make a res, I can make 2-3 identical reservoirs for the same cost it takes to buy a commercially made one.
--Reservoir Design
I have found so far that in deciding how exactly to design the reservoir, I first decide how to best fit a reservoir into the case/loop I am working on. One of the reasons for making a custom res in the first place is to tailor it to the loop/case, not vice versa. Once I get the barb placement figured out, then I design the internals. I like the top of my res to go directly to a top mounted fillport for easy filling. I also need a bottom barb to go to the pump inlet. In general, I try to place my reservoirs as close to the top of the loop as possible.
When it comes to how to design the internals, this is generally how I go about designing the res. I want the water to have to change directions, and not have an easy, direct path to the outlet/pump inlet. If it is very easy for water to go from one barb internally to the next, it will take air with it and the loop will be slower to bleed. I also allow a place for air to trap at the top of the res.
Here are a few pics of the last res that I made that I have been using for over a year. I used 4" cast acrylic tube mounted horizontally. There is a 1/4" gap between the divider and the front of the res, so that water has to go through the res from one barb to another to exit. This design has worked very well in bleeding quickly since the water has to travel which gives air time to easily rise to the top. The globe etching in the front was courtesy of Dennis at Dangerden. He responded to a forum post request and did this for me.
http://i5.photobucket.com/albums/y16...Dimensions.jpg
http://i5.photobucket.com/albums/y16...feb08/res2.jpg
This is the way it is mounted.
http://i5.photobucket.com/albums/y16...08/resBack.jpg
On the current res I am making for this case project, I decided on a narrow 2 1/4"OD 1 3/4"ID cylindrical tube 5 1/2" long total, or 5" minus end caps. The barb going into the res is placed high in the res due to the line going from the CPU to it. If possible, I want the res inlet to be above the CPU block so that air doesn't get trapped in the CPU block. I am making an internal divider that the water will hit before it goes anywhere else. This hopefully will draw bubbles to the top and fillport. I also placed a few holes further down in the divider that are 3/8" dia to let water through but hopefully help keep air from heading straight to the outlet. The divider doesn't quite go all the way down to the bottom. There is about a 1/32" gap between it and the bottom so that both sides will drain. I sure don't say that I have "the word" on res design, but hopefully this will help you work through the design if you make one.
http://i5.photobucket.com/albums/y16.../reservoir.jpg
--Starters
Rectangular reservoirs are harder to make since the cuts on the rectangular pieces have to be absolutely square. I have found it much easier to make cylindrical reservoirs. When getting acrylic to work with, get CAST acrylic only. DO NOT USE extruded acrylic for any of the pieces. If acrylic doesn't say what it is, it is extruded. You specifically need to buy acrylic that is cast. Without going into too much detail, cast acrylic is much harder and machines much better. Acrylic is a great material, but somewhat quirky, and heat is a major problem with acrylic. Cast acrylic doesn't heat up anywhere near as much as extruded does, and when machining extruded acrylic for a project like this, it is very easy to end up with problems.
Here is what can happen if you try to cut out, drill, and tap extruded acrylic. The small cracks that can be seen are called crazing, and basically are the result of the acrylic heating up too much when machining (too much stress on the material).
http://i5.photobucket.com/albums/y16...sExtruded1.jpg
http://i5.photobucket.com/albums/y16...sExtruded2.jpg
The only place so far that I have found cylindrical cast acrylic in 1' lengths is mcmaster-carr (mcmaster.com). They also have sheet cast acrylic, and round laser cut dials for the ends in 1" increments made out of cast acrylic. If you can make your res so that you can use precut round laser ends, do it. Cutting the ends can be a bit of a pain to get them round. The cast acrylic for the ends and divider that I used for this I got off of Ebay. I had to cut my own ends as I can't find precut cast ends for the 2 1/4" dia of my res. I buy cast cylindrical pieces only that are no less than 1/4" thick. The ends can be 3/16" thick, but no less as this gives adequate depth for threads for barbs. 1/4" thick for the cylinder gives a good large surface to work with when solvent welding.
--Solvent Weld
The best stuff for solvent welding the ends on is either IPS Weld-On #3, or TAP Acrylic cement (same thing) from tapplastics.com. A 4oz jar will do several reservoirs. You also want to get the needle type gauge applicator (16 gauge hypo). The needle applicator gives you very good control of how much solvent you use, whereas the bottles don't. You'll get solvent everywhere if you use them. While you are there, if you solvent weld acrylic for other purposes, you can pick up a tube of IPS Weld-On 16. It is a lot thicker and is handy for gluing together acrylic in general, but for this reservoir purpose, it leaves far too many bubbles in the seam. If properly used, this solvent weld will hold all day long at 10 times the pressure that we have in our watercooling systems.
In order to get solvent from one end to the other, I use a piece of small brass tubing that I bought locally for about a $1 at an ACE hardware store. I bent the end to make it easier to get into the bottom seams.
http://i5.photobucket.com/albums/y16...09/resGlue.jpg
--Begin the Res Build
The first thing you want to do in building a res is to cut out all of your parts, sand whatever needs sanding, drill whatever needs drilling, and tap any thread holes. You want to do all of this first so that you don't get any debris stuck in the res once its together, and you will need the barb holes to feed through to get solvent into at least one end. It took me < 1 1/2 hours to cut all of the pieces, sand all of the edges, and drill and tap the holes. If you can use laser precut ends, it would save probably 30min.
The first thing you want to do in building a res is to cut out all of your parts, sand whatever needs sanding, drill whatever needs drilling, and tap any thread holes. You want to do all of this first so that you don't get any debris stuck in the res once its together, and you will need the barb holes to feed through to get solvent into at least one end. It took me < 1 1/2 hours to cut all of the pieces, sand all of the edges, and drill and tap the holes. If you can use laser precut ends, it would save probably 30 min.
To cut the cylindrical piece of cast acrylic, I used a compound miter saw with a plywood blade. You can cut this also by hand with a simple $15 miter box. The cut however needs to be perfectly straight. If cutting with a power miter saw, don't try to cut straight through the acrylic. Use an up and down motion with the saw to cut a bit at a time. Remember, acrylic doesn't like heat so cutting in an up and down quick chopping fashion a bit at a time doesn't heat up the acrylic as much. I probably used 20-30 small up and down chops to cut the end.
Once cut, you need to get rid of all of the saw marks. I do not recommend using any power sanders for this. They tend to heat up the acrylic too much and can cause crazing when solvent welding. I sand the ends smooth by hand using a flat surface and some elbow grease. I slowly rotate the tube as I sand. I recommend sanding all the way to 400 grit (100, 150, 220, 400). It took me about 30 minutes to sand smooth both ends.
http://i5.photobucket.com/albums/y16...resSanding.jpg
--Barbs
As for what barbs to use, on every other res I have made, I used 3/8"NPT - 1/2" (3/8"threads x 1/2" barb) plastic barbs that I bought from ACE hardware. A 3/8"NPT tap to cut the thread holes can be had for about $5. NPT are tapered threads, so you would want to use plastic barbs to minimize the stress placed on the acrylic by the tapered holes with barbs tightened in them. If you try to put a brass tapered barb in a tapered hole in acrylic, you will probably cause it to craze. A bit of RTV silicone sealant is all that is needed to seal them up.
On this res, I bought a G1/4" thread tap from mcmaster. It is item no 8328A22 (search for it- G1/4"-19 BSPP thread tap) and sells for $17 + shipping. The metal barbs used for watercooling as most of us know use G1/4" British Standard Parallel threads. This really is an even better solution for using with acrylic as putting a parallel threaded barb into a parallel threaded hole causes virtually no stress on the acrylic surrounding the hole.
--Tapping Holes
If you have tapped holes before, just skip this paragraph. In case you never have, when tapping the holes, you first drill a hole with the required size. G1/4" technically call for a ll.8mm (.46") hole, but a 7/16" (.44") bit works fine. I recommend using a wood spade bit over a forstner type bit. Wood spade bits don't heat up the acrylic nearly as much as forstner bits do. You then insert the thread tap, spray it with some kind of lubricant (I use spray silicone), and keeping the tap perpendicular to the hole work the tap back and forth into the hole, cutting a bit more thread each time with each turn. I take about a 1/4 clockwise, then counterclockwise just a bit, the 1/4 turn clockwise, back a bit, and so forth. Make sure to spray more lube a few times onto your tap and in the hole. Once the thread tap stops cutting, thread it all the way through and back out of the hole, and then thread it through the other side to clean up the threads.
http://i5.photobucket.com/albums/y16...resTapping.jpg
I had to use a bit of a different approach on the side inlet, as I am using a Bitspower 45 elbow which needs a flat surface for the o-ring to seal to. I took a regular 3/4" wood spade bit and using a grinder ground the side cutting surfaces to be flat. This way the hole would be flat and wouldn't go any deeper than I wanted.
http://i5.photobucket.com/albums/y16...sDrillBits.jpg
I clamped the tube onto a piece of 2" x 4" wood to keep it steady, and drilled the 3/4" hole in just deep enough until the entire 3/4" dia of the drill bit could be seen. This way I have a flat 3/4" area. I then used a regular 7/16" spade bit to finish drilling out the middle for the threads.
http://i5.photobucket.com/albums/y16...esSideHole.jpg
--Solvent Welding
http://i5.photobucket.com/albums/y16...9/resParts.jpg
How that everything is cut and ready to use, it is time to put it all together. IPS Weld-On #3 and/or TAP plastics acrylic cement melt the edges and hence "weld" them together. This stuff is a thin as water. Welding with it is called capillary welding in case you want to Google it. I put one end on and hold it in place with blue painters tape. This way. when I put the solvent into the joint, it doesn't run all over the place on the outside.
http://i5.photobucket.com/albums/y16...09/resTape.jpg
I use the brass tube from one end to reach the seam of the other end. You want to minimize getting solvent onto the acrylic as it clouds up whatever it hits. This is why i recommend the use of the syringe type applicator to put just a bit of solvent at a time into the joint (I took the tape off here just to show better how it works-I had already done this end).
http://i5.photobucket.com/albums/y16.../resGluing.jpg
You just squirt a bit of the solvent down the hole into the joint, working it all of the way around. It will go into the joint until it pools up on the inside. Once the joint won't take anymore, pull off the tape and gently squirt solvent into the seam from the outside all the way around. You can look from the bottom to see it going into the joint. Once you have gotten as much solvent as will go into all of the joint, press down on the entire tube and end hard for about a minute or so. This is to help minimize air bubbles. Holding the tube horizontally, I then put the middle insert where I wanted, ran solvent down the sides to attach it in place, and repeated the process for the other end.
If you end up with some small bubbles in the joint, it is nothing to worry about. I have never had a res leak yet. The one I have been using now I have had in my current case for over a year.
Here is what the res looks like with all of the barbs in place.
http://i5.photobucket.com/albums/y16.../resWhole2.jpg
--Other Thoughts
I didn't build a mount into the res itself, as I will be making a separate piece for that, but you could easily modify the bottom piece to incorporate a mount. In the res I've been using for over a year, I did incorporate a mount into one end. It however has the tube laying horizontally instead of vertically.
Once done, I will let it sit for a few days before doing anything with it. Although the solvent dries quickly, it takes days for the joint to form maximum strength. I will then pressure test it with air pressure to about 30psi or so to make sure it is solid. If it holds 30psi for an hour, it isn't going to leak.
I'm sure there is more detail that I could put into this, but seeing as I have spent the last 2 hours on this, I think I've said enough. Others I'm sure can chime in with more information and clarification, but hopefully this will help someone looking to make their own res. Without the use of a lathe or something to cut channels for o-rings on the ends, this is a workable method for making a dependable, leak-free res with just a few basic hand power tools.
Trim Pieces and Edge Cutouts
Front Trim
I took my router and a 3/4" slot cutting bit and routed out the backside of the front grill to reduce the front depth from the full thickness of the wood (3/4") to 3/8". I also allowed enough room to put in trim pieces to hold the front grill cloth in place. It doesn't matter that the edges aren't straight as they will be covered with trim.
http://i5.photobucket.com/albums/y16...deRouteout.jpg
Getting the front and top trim pieces cut out was a real pain. The trim strips are only 5/16" wide x 1/4" thick, and the cutouts are only 1/16" wide. It took me several different bits and tries. I first tried a 1/16" slot cutting router bit, but it snapped in two after just the first try. I tried several Dremel bits also. Finally it was this little cutting wheel bit that did the trick. I set up a jig so that I could evenly and at the rigth depth pass the cutting wheel over the trim pieces to cut the grooves.
http://i5.photobucket.com/albums/y16...9/trimJig1.jpg
http://i5.photobucket.com/albums/y16...9/trimJig2.jpg
I then spent quite a bit of time rounding over all of the corners to give the trim a fluted appearance.
Edge Cutouts
The cutouts on the top edges were something that concerned me from the start as I wasn't sure how I was going to do them given the curve of the edge. The Dremel cuttting wheel again did the trick. I again set up a jig so that I could cut the grooves consistently across the sides and front and get them straight. I would get the depth on my Black and Decker Dremel clone, and cut the slots on all three sides so that they would match. I started with the bottom slot and worked my way up.
http://i5.photobucket.com/albums/y16...eCutoutJig.jpg
http://i5.photobucket.com/albums/y16...CutoutJig2.jpg
With a little careful marking and freehanding on the corners, here is the result:
http://i5.photobucket.com/albums/y16...un09/edge1.jpg
http://i5.photobucket.com/albums/y16...un09/edge2.jpg
Gluing
I drilled out all of the holes for dowel rods on the ends, and glued the main pieces together. It takes this step to realize why you need all of those different sizes and numbers of clamps.
http://i5.photobucket.com/albums/y16...09/gluing1.jpg
http://i5.photobucket.com/albums/y16...09/gluing2.jpg
I next have to drill the hole for the fillport, do more sanding, and glue on the top and top/front edge trim. I have to go out of town for a couple of weeks in a few days, so unfortunately I won't get the case done before I have to leave. I guess It will be waiting for me when I get back.
One last pic for this update- my security detail guarding my project. She smartly positions herself in front of the fan. She is an Australian Shepherd, and really is a very smart, quick to learn, and great guard dog. This dog also is great with kids as she is gentle as can be yet guards them tenaciously.
http://i5.photobucket.com/albums/y16...5Jun09/dog.jpg
Reservoir Mounts and Dual Pumps
Time for a few updates after my 2+ weeks out of town. This is a small update, but there should be more to follow next week.
Here is a pic of the case all glued together right now.
http://i5.photobucket.com/albums/y16...Jul09/case.jpg
I spent a good bit of time bending, adjusting, etc. to get the MB tray mounted to the rad mount/air chamber and it all mounted into the case as intended. I used an old MB and GPU to test mount with to make sure the MB tray and back panel line up right. It of course isn't staying there yet since there is more sanding to do and it has to still be stained, etc., but these had to be placed to make sure it is all fitting as planned, and so that I could make the reservoir mounts.
Reservoir Mounts
I made two mounts out of 3/16" cast acrylic to support the res so that there is no weight on the top fittings but on the mounts. Granted this is not a big reservoir (2 1/4"dia x 5"L), but I still want to make sure it is properly supported and secured.
http://i5.photobucket.com/albums/y16...res-Mounts.jpg
This is what the res looks like mounted.
http://i5.photobucket.com/albums/y16...9Jul09/res.jpg
I've next got some sanding to do on the top of the case, and then get the top and front edge trim pieces glued down.
Dual Pumps
I've made a slight change in how I think I am going to do my watercooling loop. I have been running a DDC1 now for 2yrs and 3 months, so I bought a new DDC3.1 with XSPC top. However for the sake of redundancy should my faithful DDC1 die, I think I am going to use both pumps in the loop. There is a slight difference in the head pressure between these two (the DDC1 has about 1'-2' higher head pressure), but I don't think that it is enough to matter. The way I plan on routing them both, if one should fail, it would be very easy to remove and bypass.
This is the new routing with both pumps. The bottom pump will be on some foam, and I will have to make a mount for the top pump, probably out of acrylic.
http://i5.photobucket.com/albums/y16...l09/case1F.jpg
This is how it will look still with the hard drive cage installed.
http://i5.photobucket.com/albums/y16...9/case1F-2.jpg
Top Trim, Front Trim, Side Panels and Mounts
MB Tray Mounted
I mentioned in the last post that I got the MB tray mounted to the air chamber. Here is a better pic. The MB tray mounts directly to the radiator air chamber. This way it is stable. I originally didn't plan on the air chamber idea, so I was going to be leaving some room behind the MB tray for wiring. With the air chamber however, that space is gone. I however am not too worried about it though as I think it won't be a big deal as far as wiring goes, and the benefit of having the rad air isolated far outweighs this.
http://i5.photobucket.com/albums/y16...rayMounted.jpg
Top Trim
I got the top sanded the way I wanted and have glued down the front curve and top trim pieces.
http://i5.photobucket.com/albums/y16...09/TopTrim.jpg
Front Grillcloth Mount
I made a piece to fit inside of the front grill to use to mount the grillcloth with. It completely hides the area where I routed the thickness down. I spent too much time on this piece as it really was a pain to make.
http://i5.photobucket.com/albums/y16...lothMount1.jpg
http://i5.photobucket.com/albums/y16...lothMount2.jpg
This is how it will look in place.
http://i5.photobucket.com/albums/y16...lothMount3.jpg
Front Oval Trim
I made the front oval trimpiece. This is made out of 3 pieces so that I could route the edges of the curves. I used a 1/8" cove router bit to cut the edges of the curved pieces, and then glued them to the center trim piece.
http://i5.photobucket.com/albums/y16...FrontPiece.jpg
http://i5.photobucket.com/albums/y16...rontPiece2.jpg
Since taking this photo I've gone ahead and glued the oval piece on the front and used 2 small screws on the backside for extra reinforcement.
Side Panels Mount Strips
I cut and glued in all of the 1/2" x 1/2" strips that the side panels mount to. I had to do some cutting and measuring to make sure that the metal air chamber would still properly mount with them in place. I was thinking about just having the side panels stick on with magnetic strips, but I decided against it and am using threaded inserts to screw the sides on instead.
http://i5.photobucket.com/albums/y16...SideMounts.jpg
I've cut both side panels. Here is a pic of the panel partially mounted. Instead of using the round head brass screws on the panel, I've got brass flat head screws in the mail coming my way so that the screws will sit flush with the sides.
http://i5.photobucket.com/albums/y16...ul09/Side1.jpg
Rads and Fans Mounted
In order to know exactly where the holes need to be cut into the side panel for the radiators, I needed to mount the radiators and fans onto the mount. I took both rads, cleaned them with hot soapy water, then DOW Scrubbing Bubbles, then more soapy water, then lots of rinsing, then distilled water rinses, and baked them both at 170f for a few hours to dry them out. I cut and soldered in wires for the fans, cut a hole and mounted a grommet in the air chamber, and mounted the fans and rads.
While I was screwing in the Bitspower fittings, I noticed that the metal on the fittings was going all the way down against the rads. The o-rings are too thin to seal properly on the MCR rads. So I took a trip to ACE hardware and got some thicker o-rings. I'm really glad I noticed this as I am pretty sure it would otherwise end up leaking, and taking this back apart later would be a real pain.
http://i5.photobucket.com/albums/y16...dsMounted1.jpg
http://i5.photobucket.com/albums/y16...dsMounted2.jpg
http://i5.photobucket.com/albums/y16...dsMounted3.jpg
I plan on cutting out the grills for the rads and fan on both sides tomorrow. I have a few more knick knacks still to do, but I should be ready to start staining soon. :)
Stain and Finish Done, Almost Ready for Parts
Recut the Rad Side Panel
As I mentioned, I wasn't satisfied with the radiator side panel. So I took one morning and remade it. I am much more pleased with the remade panel. I still had to drill the holes and cut the rest out with the scroll saw, but I used a spade bit which worked out much better. I left 3/8" between each cutout which made all the difference.
http://i5.photobucket.com/albums/y16...09/radSide.jpg
Stained, Urethaned, and Starting to Put It All Together
I put the dial together with the mock radio acrylic radio needles.
http://i5.photobucket.com/albums/y16...Jul09/dial.jpg
Here are some shots of how it looks at the moment. I am very pleased with how the finish came out. The stain is Ace hardware walnut. Their stains cost a bit less than Miniwax or the like and work fine. I put on two coats of stain. I used General Finishes Urethane for the top coat which was recommended to me on my last project. This stuff is great to work with as it goes on very smooth and doesn't easily run like polyurethane does which is a huge plus when working with so many small detailed areas.
http://i5.photobucket.com/albums/y16...9/urethane.jpg
I used semi-gloss and gave everything 3 coats, making sure to lightly sand out any rough spots between each coat of stain and each coat of finish. I followed up with a good wipe down with furniture polish. The finish is literally baby-butt smooth.
http://i5.photobucket.com/albums/y16...ul09/front.jpg
http://i5.photobucket.com/albums/y16...l09/front1.jpg
http://i5.photobucket.com/albums/y16...l09/front2.jpg
http://i5.photobucket.com/albums/y16...l09/front3.jpg
http://i5.photobucket.com/albums/y16...Jul09/back.jpg
Bottom
I mounted the two bottom intake fans and the DVD drive. I bought some brown strip furniture felt to line the bottom of the case with so that the bottom of the case doesn't scratch or get scratched.
http://i5.photobucket.com/albums/y16...l09/bottom.jpg
New Reservoir Mounts
For whatever reason, I just haven't liked the look of the reservoir mounts that I made. I saw this idea on another case online and kind of borrowed the idea. I took my measuring tape and picked up a piece of 2" schedule 80 PVC coupler. The inside measures 2 3/8", and the OD of my res is 2 1/4". I cut the pieces at a 10 degree angle using a miter saw, drilled countersunk holes, painted them, lined it all up, and mounted them to the air chamber using #4 bolts and nuts. I drilled and tapped holes for the #6-32 x 3/8" set screws to hold the res. I found this idea of set screws instead of normal screws while looking for something to mount the front grill cloth. They just have a thread with a small regular screwdriver slot to tighten them. I used some small rubber foam pads between the screws and the res and on the backside between the res and mounts so that the mounts grip the res well and don't scratch it.
http://i5.photobucket.com/albums/y16...Jul09/pads.jpg
http://i5.photobucket.com/albums/y16...voirMounts.jpg
http://i5.photobucket.com/albums/y16...resMounted.jpg
I just got the front grill clothe attached this morning, and have cut out and painted the grills for the other openings. I used small carpet tacks to nail it to the mounting frame, and then screwed that to the case. I thought about gluing on the cloth, but I want it to be removable if necessary.
http://i5.photobucket.com/albums/y16...grillCloth.jpg
I am almost ready to tear down my system and start moving the guts into the new case!
