DFI Lanparty UT P45-T2RS Banter starts here!!!

Printable View

Show 100 post(s) from this thread on one page

10-28-2008, 08:19 AM
C-N

DFI Lanparty UT P45-T2RS Banter starts here!!!!

Hi All,

I just got my board up & running & as there wasn't a thread already going I thought I'd make one.

Fell free to chip in :up:

CN :)

DFI Lanparty UT P45-T2RS

Click To Enlarge
http://i106.photobucket.com/albums/m...UTP45-T2RS.jpg

Code:

Specification: CPU LGA 775 socket for: - Intel® Core2 Quad and Intel® Core2 Duo Supports Intel Enhanced Memory 64 Technology (EMT64T) Supports Enhanced Intel SpeedStep Technology (EIST) Supports Intel Hyper-Threading Technology Supports 1333/1066/800MHz FSB Chipset Intel® chipset - Northbridge: Intel® P45 Express chipset Intel® Fast Memory Access technology - Southbridge: Intel® ICH10R System Memory Four 240-pin DDR2 DIMM sockets Supports DDR2 667/800/1066 MHz Delivers up to 12.8Gb/s bandwidth Supports dual channel (128-bit wide) memory interface Supports up to 8GB system memory Supports unbuffered x8 and x16 DIMMs Expansion Slots 2 PCI Express (Gen 2) x16 slots (PCIE 1 and PCIE 3) - 2-way CrossFire at x8/x8 bandwidth - 2-way CrossFire + Physics at x8/x8/x4 bandwidth 1 PCI Express x1 slot (PCIE 2) 1 PCI Express x4 slot (PCIE 4) 3 PCI slots BIOS Award BIOS 8Mbit SPI flash memory CMOS Reloaded Audio Bernstein audio module - Realtek ALC885 8-channel High Definition Audio CODEC - Center/subwoofer, rear R/L and side R/L jacks - Line-in, line-out (front R/L) and mic-in jacks - 2 coaxial RCA S/PDIF-in/out jacks - 1 optical S/PDIF connector - 1 CD-in connector - 1 front audio connector DAC SNR/ADC SNR of 106dB/101dB Full-rate lossless content protection technology LAN Marvell 88E8052 and Marvell 88E8053 PCIE Gigabit LAN controllers Fully compliant to IEEE 802.3 (10BASE-T), 802.3u (100BASE-TX) and 802.3ab (1000BASE-T) standards Storage Intel ICH10R chip - Intel Matrix Storage technology - Supports up to 6 SATA devices - SATA speed up to 3Gb/s - RAID 0, RAID 1, RAID 0+1 and RAID 5 JMicron JMB363 PCI Express to SATA and PATA host controller - Supports up to 2 UltraDMA 100Mbps IDE devices - Supports 2 SATA devices - SATA speed up to 3Gb/s - RAID 0 and RAID 1 IEEE 1394 VIA VT6307 Supports two 100/200/400 Mb/sec ports Rear Panel I/O 1 Mini-DIN-6 PS/2 mouse port 1 Mini-DIN-6 PS/2 keyboard port 1 IEEE 1394 port 6 USB 2.0/1.1 ports 2 RJ45 LAN ports Internal I/O 3 connectors for 6 additional external USB 2.0 ports 1 connector for an external COM port 1 connector for an IEEE 1394 port 1 connector for the Bernstein audio module 1 IrDA connector 1 CIR connector 8 Serial ATA connectors 1 40-pin IDE connector 1 floppy connector 1 24-pin ATX power connector 1 8-pin 12V power connector 2 4-pin 5V/12V power connectors (FDD type) 1 front panel connector 6 fan connectors 1 diagnostic LED EZ touch switches (power switch and reset switch) Power Management ACPI and OS Directed Power Management ACPI STR (Suspend to RAM) function Wake-On-PS/2 / Wake-On-USB Keyboard/Mouse Wake-On-LAN and Wake-On-Ring RTC timer to power-on the system AC power failure recovery Hardware Monitor Monitors CPU/system/Northbridge temperature and overheat alarm Monitors Vcore/Vdimm/Vnb/VCC5/12V/V5sb/Vbat voltages Monitors the speed of the cooling fans CPU Overheat Protection function monitors CPU temperature and fan during system boot-up - automatic shutdown upon system overheat PCB 6 layers, ATX form factor; 24.5cm (9.64") x 30.5cm (12")

BIOS screen shots [1007]

1: Overview CMOS Setup, 2: STD CMOS Features, 3: Advanced BIOS Features 1, 4: Advanced BIOS Features 2, 5: Advanced Chipset Features.

http://i106.photobucket.com/albums/m...wCMOSSetup.jpg http://i106.photobucket.com/albums/m...OSFeatures.jpg http://i106.photobucket.com/albums/m...SFeatures1.jpg http://i106.photobucket.com/albums/m...SFeatures2.jpg http://i106.photobucket.com/albums/m...etFeatures.jpg

6: Integrated Periferals, 7: Power Management Setup, 8: PnP & PCI Configuration1, 9: PC Health Status, 10: Genie BIOS Setting 1.

http://i106.photobucket.com/albums/m...Periferals.jpg http://i106.photobucket.com/albums/m...ementSetup.jpg http://i106.photobucket.com/albums/m...igurations.jpg http://i106.photobucket.com/albums/m...althStatus.jpg http://i106.photobucket.com/albums/m...OSSetting1.jpg

11: Genie BIOS Setting 2, 12: CPU Features, 13: DRAM Timing 1, 14: Clock Setting Fine Delay 1, 15: Clock Setting Fine Delay 2

http://i106.photobucket.com/albums/m...OSSetting2.jpg http://i106.photobucket.com/albums/m...CPUFeature.jpg http://i106.photobucket.com/albums/m...RAMTiming1.jpg http://i106.photobucket.com/albums/m...FineDelay1.jpg http://i106.photobucket.com/albums/m...FineDelay2.jpg

16: Dram Timing 2, 17: Voltage Setting

http://i106.photobucket.com/albums/m...RAMTiming2.jpg http://i106.photobucket.com/albums/m...ageSetting.jpg

Downloads

Manual

dfi.com.tw Click Here

BIOS

dfi.com.tw 1007 BIOS Click Here

Beta BIOS

Posted by namegt 1028 BIOS Click Here

dfi.com.tw 1212 BIOS Click Here

dfi.com.tw 0112 BIOS Click Here

Product Information, Recommended Memory, CPU Compatability,Drivers & Apps

dfi.com.tw Click Here

Reviews

Clunk.org Click Here

OCDB (Over Clock Data Base) Post up your stable clocks.

Kitfit: E8600 @ 5GHZ DDR1200 10H Prime Blend Stable Post 63 Click Here Link to Settings Click Here

CN: E8500 @ 4.5GHZ DDR1186 9.5H Prime Blend Stable Post 63 Click Here

CN: Q9650 @ 4350MHZ DDR1160 9.25H Prime Blend Stable Post 277 Click Here

CN: Q9650 @ 4.3GHZ DDR1150 9.5H Prime Blend Stable Post 257 Click Here

PolRoger: E8600 @ 4.25GHZ DDR1218 2H OCCT Stable Post 45 Click Here

SOXX: Q9550 @ 4.2GHZ 3H Prime Stable Post 395 Click Here

CN: Q9650 @ 4.2GHZ DDR1166 8H Prime Blend Stable Post 230 Click Here

Peter Burg: Q9550 @ 4.0GHZ 1H Prime Small Stable Post 194 Click Here

SOXX: Q9550 @ 4.0GHZ 2.5H Prime Stable Post 328 Click Here

prostoman: QX9650 @ 4.0GHZ 13H Prime Stable Post 278 Click Here

Code:

andrewmodus: Q9650 @ 4.0GHZ 10H Prime Blend Stable Post 370 Click Here Thule: Q9550 @ 3958MHZ 3H Prime Stable Post 276 Click Here

FSB Race Track

Dual Core

CN: 625 E8500 Click Here

namegt: 600 E8400 Click Here

kitfit1: 563 E8600 Click Here

PolRoger: 500 E8600 Click Here

Quad Core

Super PI Race Track

1M

namegt: E8400 556 X 9 9.390 seconds 1M Click Here

prostoman: E8600 500 X 9 9.499 seconds 1M Click Here

CN: E8500 600 X 8 9.687 seconds 1M Click Here

namegt: E8400 534 X 9 9.734 seconds 1M Click Here

prostoman: QX9650 392 X 12 9.953 seconds 1M Click Here

32M

namegt: E8400 556 X 9 10m 19.781 seconds 32M Click Here

roedzzz: E8600 600 X 7.5 10m 25.473 seconds 32M Click Here

Everest Cache & Memory Benchmarks

473 x 9.5, 592 mem Read: 10480 Latency: 48.5ns Click Here

520 x 8, 624 mem Read: 10814 Latency: 47.0ns Click Here

530 x 8, 636 mem Read: 11019 Latency: 46.2ns Click Here

540 x 8, 648 mem Read: 11219 Latency: 45.4ns Click Here

550 x 8, 660 mem Read: 11428 Latency: 44.4ns Click Here

560 x 8, 672 mem Read: 11662 Latency: 44.0ns Click Here

560 x 9.5, 672 mem Read: 11805 Latency: 43.4ns Click Here

562 x 9.5, 675 mem Read: 11925 Latency: 42.5ns Click Here

600 x 8 600 mem Read: 11204 Latency: 46.2ns Click Here

Smartguardian Skin (Use with DFI DK non plus Smartguardian) Thanks to DJ Sub for the Background

Dual Core SG Skin Click Here
10-28-2008, 08:41 AM
MacClipper

Is that an actual photo of your shipped mobo? Cos there is definitely no BIOS chip socket (only the mask) on the final retail mobo I am holding over here.

Anyway photos of the actual mobo can be viewed in my VRZ post.
http://forums.vr-zone.com/showpost.p...2&postcount=18
10-28-2008, 08:45 AM
Viss

Please test spi 1M with oldest bios :D
10-28-2008, 08:49 AM
Shiranui Gen-An

Nice to see someone who actually has one of these boards, I wonder how it will compare to the Maximus II Formula and EP45-Extreme.
10-28-2008, 08:56 AM
Kean

Yeah!
At the end somebody has it.
I'm waiting for scores ;)
10-28-2008, 09:18 AM
C-N

Quote:

Originally Posted by MacClipper

Is that an actual photo of your shipped mobo? Cos there is definitely no BIOS chip socket (only the mask) on the final retail mobo I am holding over here.

Anyway photos of the actual mobo can be viewed in my VRZ post.
http://forums.vr-zone.com/showpost.p...2&postcount=18

No I didn't see a need as you had already done the photos & I was hoping you might chip in with your link :D

My board is already hooked up, my board looks just like your actual photos with no BIOS holder & square illuminated power/reset buttons. I'll add a pic later gotta fix my Moto X bike first.
10-28-2008, 09:33 AM
MacClipper

heheh, do get cracking on clocking will you? :D

Cos I still don't have any spare test CPU around which can do justice to this mobo, hoping to get a E3110 or E8400 this weekend though. :)
10-28-2008, 09:34 AM
eva2000

nice i should have these boards to play with later too.. can you check what clock generator it uses ?
10-28-2008, 10:17 AM
MTP04

I've been waiting patiently for this board to come out. I hope OC is as good or better than the P35 version. Looking forward to some results.:)
10-28-2008, 10:41 AM
NapalmV5

nice.. just like the ut p35.. but

hope unlike ut p35 itll bios option more than just a measly 1.45vtt

if oscar bumps vtt to 2v ill surely get ut p45 aswell :up:
10-28-2008, 10:51 AM
nikk

seriously sweet mobo, can't wait for oc results:cool:
10-28-2008, 10:53 AM
kitfit1

I should have mine by the weekend, looking forward to being able to run at 600fsb 1:1. Did you get your's from Germany C-N ? ordered mine from there. If you did what sort of time did you have to wait for delivery ?
10-28-2008, 02:05 PM
C-N

Quote:

Originally Posted by eva2000

nice i should have these boards to play with later too.. can you check what clock generator it uses ?

Same as DK P45 9LPRS918JKLF

Quote:

Originally Posted by NapalmV5

nice.. just like the ut p35.. but

hope unlike ut p35 itll bios option more than just a measly 1.45vtt

if oscar bumps vtt to 2v ill surely get ut p45 aswell :up:

1.7V vtt here

Quote:

Originally Posted by kitfit1

I should have mine by the weekend, looking forward to being able to run at 600fsb 1:1. Did you get your's from Germany C-N ? ordered mine from there. If you did what sort of time did you have to wait for delivery ?

With the exception of my DK P45 I have always got my DFI boards from Germany (the service is ace). I ordered it Friday lunchtime.
10-28-2008, 02:15 PM
NapalmV5

1.7vtt is not enough :( oh well
10-28-2008, 02:38 PM
MTP04

C-N, can you see if setting pcie frequency to 135 or 140 mhz works on this board?
10-28-2008, 04:54 PM
Breogan

Where are you ordering them from? Alternate?
10-28-2008, 05:55 PM
zsamz_

i been dreamin of that board:rofl:
but i really wanna see if its as fast as the ut p35
cause x38 was a waste compared to the ut p35
10-28-2008, 07:04 PM
emoners

nice C-N! :up:

by the way, will there be a X48 JR?
10-28-2008, 07:53 PM
philbrown23

omg i love it!, I'm either getting this or the maximus 2 then ima sell my p35 or this biostar, prolly this board as it's a tad fishy with what ram it likes .
10-29-2008, 01:29 AM
C-N

Quote:

Originally Posted by MacClipper

I still don't have any spare test CPU around which can do justice to this mobo.

Apparently I don't either!!! E8500 that easily done 625fsb in my DK P45 on Monday night couldn't make 600 in the UT last night only made it to 590fsb. Not that I really go for fsb or anything but my P35 1 year on can still make 600fsb without breaking a sweat so it looks like I've got some work to do.

Quote:

Originally Posted by MTP04

C-N, can you see if setting pcie frequency to 135 or 140 mhz works on this board?

Without trying properly the answer is no, 115mhz is where it starts getting funky but having said that it really depends on a lot of things, if I really wanted every last mhz I am sure I could find another few. I suspect using the JMicron would get me into the 125mhz band without trying to hard.

Quote:

Originally Posted by Breogan

Where are you ordering them from? Alternate?

Ye they have them so do SLT/Trend but I usually use HPM.

Quote:

Originally Posted by zsamz_

i been dreamin of that board:rofl:
but i really wanna see if its as fast as the ut p35
cause x38 was a waste compared to the ut p35

Ye I know what you mean its a bit overdue!!!

I think its got its work cut out to match the P35's ability to enable every man & his dog (self included) to reach wild frequency's & speeds whilst running smooth, stable & cool. The P45 is a quick board it doesn't feel so free as the P35 but with the exception of fsb my P45 can do everything my P35 can/could.

The P45 makes Crossfire worth doing which is probably its best advantage over P35. I had both an X38 & an X48 & the boards were good all be it fsb limited which was made that much worse coming from a P35 basically the king of fsb at the time.

Quote:

Originally Posted by emoners

nice C-N! :up:

by the way, will there be a X48 JR?

I honestly don't know, I doubt it as the P45 is sufficient for Crossfire.
10-29-2008, 04:30 AM
MTP04

Quote:

Originally Posted by C-N

Without trying properly the answer is no, 115mhz is where it starts getting funky but having said that it really depends on a lot of things, if I really wanted every last mhz I am sure I could find another few. I suspect using the JMicron would get me into the 125mhz band without trying to hard.
.

I guess your using a sata hard drive? My Biostar Tpower P45 board is limited to just 106mhz before it gets unstable and thats with a pata drive. So 115mhz inst bad but I hope it gets better with bios updates. Thanks for trying.:)
10-29-2008, 10:49 AM
politenessman

came in stock at newegg about 30 minutes ago (as far as i can tell). in for 1. will report back here. if it ships from nj, i will have it tomorrow or friday, if not, then friday or sat.
10-29-2008, 01:50 PM
C-N

Super PI 1M

Quote:

Originally Posted by loc.o

Please test spi 1M with oldest bios :D

:D Found some fsb, me bad had way too much vtt :shrug:

Nothing world class but It'll give you an idea.

XP SP3/Dirty no tweaks just dialed in & run.

I only have the shipping BIOS.

600 X 6

http://i106.photobucket.com/albums/m...th_600x61M.jpg

600 X 7

http://i106.photobucket.com/albums/m...th_600x71M.jpg

600 X 8

http://i106.photobucket.com/albums/m...th_600x81M.jpg

BIOS / RAM primary's

http://i106.photobucket.com/albums/m...FSB/th_615.jpg
10-30-2008, 03:41 AM
chuchnit

I wanna see some more results out of this board. I've been waiting on this since I saw the press release on DFI's site.
10-30-2008, 04:06 AM
C-N

Quote:

Originally Posted by chuchnit

I wanna see some more results out of this board. I've been waiting on this since I saw the press release on DFI's site.

I haven't seen anything/anyone out there do anything with this board I think the imminent release of Nehalem may be overshadowing it somewhat. Its early days for the UT P45 & I'm sure someone else other than just me will buy it :D & so just hang fire.

On the plus side I think I've got it all sussed out now & should in a position to lay down a decent daily overclock with some 3D benches in the next few days I'll keep the thread posted.

In the mean time from a performance point of view it drives just like the DK P45 but the UT has a bigger PWM that should handle a quad getting raped, the layout although a bit tight is better & the board I suppose being 6 layer rather than 4 handles a fair bit more voltage & runs a bit smoother/stronger than the DK P45.

Is there a bench in particular that you would like me to run for you or are you just looking for results in general from other with this board?

CN :)
10-30-2008, 06:51 AM
chuchnit

Quote:

I haven't seen anything/anyone out there do anything with this board I think the imminent release of Nahelm may be overshadowing it somewhat. Its early days for the UT P45 & I'm sure someone else other than just me will buy it & so just hang fire.

On the plus side I think I've got it all sussed out now & should in a position to lay down a decent daily overclock with some 3D benches in the next few days I'll keep the thread posted.

In the mean time from a performance point of view it drives just like the DK P45 but the UT has a bigger PWM that should handle a quad getting raped, the layout although a bit tight is better & the board I suppose being 6 layer rather than 4 handles a fair bit more voltage & runs a bit smoother/stronger than the DK P45.

Is there a bench in particular that you would like me to run for you or are you just looking for results in general from other with this board?

CN

Thanks for the detailed response. I see that it already seems to be up to par with other high end P45's. As far as benches it would be nice to see some everest memory benches and of course the usual suspects of 3D benches as you stated you'll be doing.

Would it be to much to ask for some shots of the bios? I've wanted a DFI board for some time now and I'm pretty excited about this one! You are right though. It did just launch so I suspect in the coming days we will see more and more people come out of the woods with their take on this. I just hope this is liked as well as the UT-P35 boards.

BTW, do you know if there is any issues with the current bios and 4870x2 cards? Thanks again.:up:
10-30-2008, 07:09 AM
nugzo

Its out on the heels of gigabytes new EP45 UD3 series..Which is cheap and also does crazy FSB. What would be the advantages to going with the DFI over the UD3?
10-30-2008, 07:34 AM
chuchnit

Quote:

Originally Posted by nugzo

Its out on the heels of gigabytes new EP45 UD3 series..Which is cheap and also does crazy FSB. What would be the advantages to going with the DFI over the UD3?

Honestly I don't have a good answer for that. The UD3 boards seem to be amazing so far! I've wanted a DFI after hearing about the awesome overclocking and bios of the DFI's. I just wasn't that impressed with the X38/48 results. IMHO if money wasn't an issue I would either pick up this board or the P5Q-deluxe. In no way am I saying the UD3 boards are inferior though. I almost picked one up a couple of weeks ago from the egg.
10-30-2008, 07:58 AM
nugzo

Quote:

Originally Posted by chuchnit

Honestly I don't have a good answer for that. The UD3 boards seem to be amazing so far! I've wanted a DFI after hearing about the awesome overclocking and bios of the DFI's. I just wasn't that impressed with the X38/48 results. IMHO if money wasn't an issue I would either pick up this board or the P5Q-deluxe. In no way am I saying the UD3 boards are inferior though. I almost picked one up a couple of weeks ago from the egg.

I guess its gonna take time to tell if the UD3 is gonna be a good deal or not. I've already heard of dead boards and 3 dead Nice CPU's. Gigabyte cant stop putting out bios updates either when needed... That is probably where DFI will win out. Oscar normally keeps up with a new Bios when needed. I bet everyone will jump on the extra copper soon to though. I'll be keeping my eye on this DFI for some Quad clocks.
10-30-2008, 08:39 AM
C-N

Quote:

Originally Posted by chuchnit

Thanks for the detailed response. I see that it already seems to be up to par with other high end P45's. As far as benches it would be nice to see some everest memory benches and of course the usual suspects of 3D benches as you stated you'll be doing.

Would it be to much to ask for some shots of the bios? I've wanted a DFI board for some time now and I'm pretty excited about this one! You are right though. It did just launch so I suspect in the coming days we will see more and more people come out of the woods with their take on this. I just hope this is liked as well as the UT-P35 boards.

BTW, do you know if there is any issues with the current bios and 4870x2 cards? Thanks again.:up:

No trouble at all I got a bit carried away last night with other stuff & totally forgot to take some BIOS Screen shots, I'll do it tonight.

I have a Gecube 4870x2 in it right now & its running sweet.

Quote:

Originally Posted by nugzo

Its out on the heels of gigabytes new EP45 UD3 series..Which is cheap and also does crazy FSB. What would be the advantages to going with the DFI over the UD3?

I couldn't really tell you but as far as I have seen the Giga is a champ board. I would say perhaps the DFI DK P45 was more in its price band though.

The only other thing that I have seen & it caught my eye was the voltages the Giga pump out on auto. I have seen great things from the Giga but every single screen shot has made me cringe at the voltages. I don't know if the Giga would run the same sort of speed/performance on low/mild voltage or not but I can tell you the DFI UT P45 can easily do 600+fsb with 1.24v vtt, 1.4vnb & 1.5v pll (safe) which for me makes the DFI the Rolls Royce choice for me.
10-30-2008, 09:09 AM
C-N

Just noticed its in stock @ Scan here in the UK

Credit where credit is due :up: DFI for a decent UK launch, gone are the days when you had to wait 2 months after it was released in the USA :clap:

.
10-30-2008, 03:41 PM
C-N

2 Attachment(s)

Quote:

Originally Posted by chuchnit

It would be nice to see some everest memory benches

I put up some BIOS screen shots on the 1st page.

Here are a couple of Everest Cache & Memory benches, The first is just something I happened to run last night & the second is where I think I will be able to run daily & complete a loop of Prime.

http://i106.photobucket.com/albums/m...yBenchmark.jpg

http://i106.photobucket.com/albums/m...45266Strap.jpg

I have also attached a tweaked Smartguardian skin free for anyone that wants it.

CN :)
10-30-2008, 05:40 PM
PolRoger

I got a UD3P last Friday... and so far I'm having favorable first impressions. I'm still working on high fsb overclocks and I've seen some screenshots out there with some high voltages... more time and testing will tell if that is what the board really requires. I liked my LP JR enough that my new UT is scheduled to arrive tomorrow!
10-30-2008, 05:54 PM
MTP04

C-N, what was the PL set to with the 600mhz Everest run?
10-30-2008, 06:09 PM
chuchnit

Thanks C-N :clap::up:
10-30-2008, 11:54 PM
C-N

Quote:

Originally Posted by PolRoger

I got a UD3P last Friday... and so far I'm having favorable first impressions. I'm still working on high fsb overclocks and I've seen some screenshots out there with some high voltages... more time and testing will tell if that is what the board really requires. I liked my LP JR enough that my new UT is scheduled to arrive tomorrow!

He he you sound just as mad as me with buying all those new boards I love it. It would be nice to compare the the Giga keep us posted.

Quote:

Originally Posted by MTP04

C-N, what was the PL set to with the 600mhz Everest run?

Nothing special it was just PL10 default for 1:1 600/667.

The 2nd shot was PL7.
10-31-2008, 12:15 AM
zsamz_

C-N so the ut p45 is just as fast as the ut p35?
is it a worthy upgrade or they both about equal?
can you do a 510-525 fsb run with everest score 333/800 divider
ty
10-31-2008, 01:27 AM
C-N

Quote:

Originally Posted by zsamz_

C-N so the ut p45 is just as fast as the ut p35?
is it a worthy upgrade or they both about equal?
can you do a 510-525 fsb run with everest score 333/800 divider
ty

Yup the UT P45 is sweet imo, the difference between the P35 & P45 in daily use is nothing you will notice so its probably not worth the upgrade unless you are like me & just like new stuff. The advantage is Crossfire with PCI-E 2 & the nb voltage runs way lower than the P35.

I think the UT P45 is a real nice board however its just out & its on its 1st official BIOS & there is still some work to be done. Just quick observations the vcore you need to set in BIOS for example 1.5* set shows 1.43 in SG 1.44 in CPU-Z under load & the droop control thingy doesn't really make much difference. The 333/800 strap divider does not run properly I haven't played for long with it but I'm fairly sure there is a problem with it. I am also sure DFI will be able to pull a bit more bandwidth out of the memory once its matured a bit but thats just my feeling.

I wont have time to try the 333/800 510~525mhz everest run tonight (I'm doing Dracula tonight for Halloween lol) but I'll give it a go tomorrow for you.
10-31-2008, 05:48 AM
screwtech02

Anybody stuck a Q6600 in this board and pushed it yet???
10-31-2008, 06:17 AM
chuchnit

Quote:

Originally Posted by screwtech02

Anybody stuck a Q6600 in this board and pushed it yet???

It just hit newegg a couple of days ago. I suppose it will take a couple of weeks for more users to pop up.
11-01-2008, 01:04 PM
knopflerbruce

This board looks nice, maybe I can sell my lt x48 and buy this without paying too much extra:) Looks to be quite decent in terms of FSB (the 600+ numbers posted were on air...?) at least.

Not sure anyone noticed, but the PCB is nearly the exact same as the one used on the LT/UT X48-T2R. Except that DFI used 3 more capacitors on the UT P45 than on the LT X48 (2 near the memory slots and one close to the SB). I guess the memory freaks will love that:p:
11-01-2008, 02:39 PM
deadman'sclick

nice thread c-n :) hows it going m8 :up:

wish i had more spare cash & time atm :( i would get this board & a e8600 stright away.

sum proper nice clocks u got going.

regards

gm :D
11-01-2008, 04:19 PM
vws

Quote:

Originally Posted by MacClipper

Is that an actual photo of your shipped mobo? Cos there is definitely no BIOS chip socket (only the mask) on the final retail mobo I am holding over here.

Anyway photos of the actual mobo can be viewed in my VRZ post.
http://forums.vr-zone.com/showpost.p...2&postcount=18

So I take it DFI no longer supports replaceable BIOS chip on the UT P45? :confused:
11-01-2008, 09:20 PM
zsamz_

Quote:

Originally Posted by vws

So I take it DFI no longer supports replaceable BIOS chip on the UT P45? :confused:

thats bs for a high end board
wow they saved 50 cents:rofl:
11-01-2008, 09:26 PM
PolRoger

4 Attachment(s)

My board arrived on Friday and I've just started testing it on an open test bench. The Bios is quite similar to my LP JR except for the VTT/MCH GTL refs. The UT has four individual adjustments for VTT and two individual adjustments for MCH. Whereas the LP JR has just two for VTT and one for MCH.

There appears to be a clearance issue with the Northbridge using my Xigmatek S-1283 with it blowing towards the I/O sheild so I rotated it and I've got it mounted in a top to bottom orientation.

Here is my starting overclock 500x8.5 333/800 divider DDR2-1200 using a 2gb kit of OCZ Reaper PC2-9200. VDroop enabled, Fine Clock Delay: 0-0-1, VTT refs at 63 and MCH refs at 61.
11-02-2008, 02:26 AM
vws

Quote:

Originally Posted by zsamz_

thats bs for a high end board
wow they saved 50 cents:rofl:

Whoa... define "high end"? Isn't 'highly customizable' the major trait of a high-end motherboard? So customizable, when anything fails due to extreme customization there's always a fall-back way to save it? And since when that becomes a BS?

I, for one, can't see a mediocre implementation such as gigabyte's dual-bios as "high-end", where any simple mis-step may easily result in that dreadful reboot cycle which is never fixable. Don't assume DFI is able make an infallible microcode/bootchip that would never make any fault like that - we've all seen how sloppy they've become lately. In fact, the tried-and-true hotflash method may still be the saving grace when the time comes. Now if they are really getting rid of the BIOS chip I hope they at least elaborate their new fall-back plan when the BIOS gets corrupted. If there's none, it'd just be another indication that they are taking 0 pride in making their "high-end" product.
11-02-2008, 05:11 AM
C-N

@ VWS the new style tiny bios chips do come out of there plastic holder just pop the top open & easily lift the chip out.

I eventually got round to doing the 3D runs & it does look good :D

Stock 4870x2

CPU-Z

http://i106.photobucket.com/albums/m...tock/CPU-Z.jpg

Aquamark

http://i106.photobucket.com/albums/m...k/Aquamark.jpg

3DMARK01

http://i106.photobucket.com/albums/m...k/3DMARK01.jpg

3DMARK03

http://i106.photobucket.com/albums/m...k/3DMARK03.jpg

3DMARK05

http://i106.photobucket.com/albums/m...k/3DMARK05.jpg

3DMARK06

http://i106.photobucket.com/albums/m.../3dDMARK06.jpg

Quote:

Originally Posted by deadman'sclick

nice thread c-n :) hows it going m8 :up:

wish i had more spare cash & time atm :( i would get this board & a e8600 stright away.

sum proper nice clocks u got going.

regards

gm :D

Thanks mate & nice to hear from you.

I'm in the same boat as you no spare time right now either & I have a winter project (boat) sucking up all my spare cash.

The board clocks like a champ I'm well chuffed with it.

CN :)
11-02-2008, 08:04 AM
kitfit1

@ C-N, do you think you could post up a bios template of your settings for 600fsb. Although we all have different ram and setups, it would still be usefull to show peeps in the important bits that need to be worked on ?
11-02-2008, 08:31 AM
philbrown23

so why is this DFI so much more expensive and hard to find (cept at newegg) than say the DK P45 wich can hit amazin fsb's? is it just that damn good?
11-02-2008, 02:53 PM
vws

1 Attachment(s)

Quote:

Originally Posted by C-N

@ VWS the new style tiny bios chips do come out of there plastic holder just pop the top open & easily lift the chip out.

Cool! Is that the tiny one next to the south bridge as shown in this picture?
11-02-2008, 02:59 PM
C-N

Quote:

Originally Posted by kitfit1

@ C-N, do you think you could post up a bios template of your settings for 600fsb. Although we all have different ram and setups, it would still be usefull to show peeps in the important bits that need to be worked on ?

Sure here you go.

Code:

>CPU Feature: Thermal Management Control.......... - Disabled PPM(EIST) Mode...................... - Disabled Limit CPUID MaxVal.................. - Disabled CIE Function........................ - Disabled Execute Disable Bit................. - Disabled Virtualization Technology........... - Disabled Core Multi-Processing............... - Enabled >DRAM Timing: Enhance Data transmitting........... - Fast Enhance Addressing.................. - Fast T2 Dispatch......................... - Auto >Clock Setting Fine Delay Press Enter: DLL And RCOMP Settings.............. - Auto Ch1 Dram Defaul Skew................ - Model 3 Ch2 Dram Defaul Skew................ - Model 3 RCOMP Settings...................... - Model 1 Fine Delay Step Degree.............. - 70ps Ch1 Clock Crossing Setting.......... - Relaxed DIMM1 Clock Fine Delay.............. - Current[2396ps] DIMM2 Clock Fine Delay.............. - Current[2396ps] Ch1 Control0 Fine Delay............. - Current[268ps] Ch1 Control1 Fine Delay............. - Current[268ps] Ch1 Control2 Fine Delay............. - Current[268ps] Ch1 Control3 Fine Delay............. - Current[268ps] Ch1 Command Fine Delay.............. - Current[394ps] Ch2 Clock Crossing Setting.......... - Relaxed DIMM3 Clock Fine Delay.............. - Current[2066ps] DIMM4 Clock Fine Delay.............. - Current[2066ps] Ch2 Control0 Fine Delay............. - Current[48ps] Ch2 Control1 Fine Delay............. - Current[48ps] Ch2 Control2 Fine Delay............. - Current[48ps] Ch2 Control3 Fine Delay............. - Current[48ps] Ch2 Command Fine Delay.............. - Current[394ps] Ch1 Ch2 Common Clock Setting........ - Relaxed Ch1 RDCAS GNT-Chip Delay............ - Auto Ch1 WRCAS GNT-Chip Delay............ - Auto Ch1 Command To CS Delay............. - Auto . Ch2 RDCAS GNT-Chip Delay............ - Auto Ch2 WRCAS GNT-Chip Delay............ - Auto Ch2 Command To CS Delay............. - Auto Flex Memory Mode..................... - Auto CAS Latency Time (tCL)............... - 5 RAS# to CAS# Delay (tRCD)............ - 5 RAS# Precharge (tRP)................. - 5 Precharge Delay (tRAS)............... - 12 All Precharge to Act................. - 5 REF to ACT Delay (tRFC).............. - 30 Performance Level.................... - Auto >Read delay phase adjust Press Enter: Channel 1 Phase 0 Pull-In........... - Auto Channel 1 Phase 1 Pull-In........... - Auto Channel 1 Phase 2 Pull-In........... - Auto Channel 1 Phase 3 Pull-In........... - Auto Channel 1 Phase 4 Pull-In........... - Auto Channel 2 Phase 0 Pull-In........... - Auto Channel 2 Phase 1 Pull-In........... - Auto Channel 2 Phase 2 Pull-In........... - Auto Channel 2 Phase 3 Pull-In........... - Auto Channel 2 Phase 4 Pull-In........... - Auto Write to PRE Delay (tWR)............ - 13 Rank Write to Read (tWTR)........... - 12 ACT to ACT Delay (tRRD)............. - 3 Read to Write Delay (tRDWR)......... - 8 Ranks Write to Write (tWRWR)........ - Auto Ranks Read to Read (tRDRD).......... - Auto Ranks Write to Read (tWRRD)......... - Auto ALL PRE to Refresh.................. - Auto >Voltage Settings: CPU VID Control..................... - 1.33125V CPU VID Special Add................. - Enabled CPU VID Special Add................. - Auto DRAM Voltage Control................ - 2.27v SB Core/CPU PLL Voltage............. - 1.55v NB Core Voltage..................... - 1.455v CPU VTT Voltage..................... - 1.24v Vcore Droop Control................. - Enabled Clockgen Voltage Control............ - 3.60v GTL+ Buffer Strength................ - Strong CPU GTL 0 REF Volt.................. - 0.6225 CPU GTL 2 REF Volt.................. - 0.6225 CPU GTL 1 REF Volt.................. - 0.6225 CPU GTL 3 REF Volt.................. - 0.6225 North Bridge GTL 0 REF Volt......... - 0.6275 North Bridge GTL 1 REF Volt......... - 0.6275 FSB Vref............................ - Auto Genie BIOS Settings: Exist Setup Shutdown................ - Mode 2 Exist Shutdown After AC loss........ - Enabled AC Shutdown Free.................... - Enabled O.C Clock Fail Retry Counter........ - 0 O.C Clock Fail CMOS Reloaded........ - Disabled CPU Clock Ratio..................... - 6 Target CPU Clock.................... - 3303MHz CPU Clock........................... - 550 Boot Up Clock....................... - Auto CPU Clock Amplitude................. - 800mV CPU Clock0 Skew..................... - 200ps CPU Clock1 Skew..................... - 0ps DRAM Speed.......................... - 333/667 Target DRAM Speed................... - 1101MHz PCIE Clock.......................... - 100mhz PCIE Slot Config.................... - 1x 1x CPU Spread Spectrum................. - Disabled PCIE Spread Spectrum................ - Disabled
11-02-2008, 03:01 PM
C-N

Quote:

Originally Posted by vws

Cool! Is that the tiny one next to the south bridge as shown in this picture?

Yup thats it :up:
11-02-2008, 03:50 PM
C-N

Quote:

Originally Posted by zsamz_

can you do a 510-525 fsb run with everest score 333/800 divider
ty

333/800 running fine duno what I was doing wrong the other day :shrug:

Kinda makes you wonder what the DDR3 board would be like dont it :D

520 x 8

http://i106.photobucket.com/albums/m...ache/520x8.jpg

530 x 8

http://i106.photobucket.com/albums/m...ache/530x8.jpg

540 x 8

http://i106.photobucket.com/albums/m...ache/540x8.jpg

550 x 8

http://i106.photobucket.com/albums/m...ache/550x8.jpg

560 x 8

http://i106.photobucket.com/albums/m...ache/560x8.jpg
11-02-2008, 06:44 PM
emoners

@C-N: seems like you're enjoying this board :D
11-02-2008, 07:27 PM
zsamz_

Quote:

Originally Posted by C-N

333/800 running fine duno what I was doing wrong the other day :shrug:

Kinda makes you wonder what the DDR3 board would be like dont it :D

nice verry nice the scores are not far off the ut p35
it has the best bandwidth i seen in 45 if dfi doesnt drop the ball it can be better than the ut p35 in 6 months
tks C_N
:mad:you givin me the itch for another dfi board
11-02-2008, 09:04 PM
nugzo

Will a TRUE fit this board? That NB HS looks real tall.
11-02-2008, 09:30 PM
MacClipper

Quote:

Originally Posted by nugzo

Will a TRUE fit this board? That NB HS looks real tall.

Fits both directions with no problems at all.
11-02-2008, 11:58 PM
DJSUB

wow very nice result c-n :D
i'm gonna buy this board :up:
11-03-2008, 01:04 AM
radaja

@c-n, those everest scores look awesome! think i might get this board soon!
11-03-2008, 01:40 AM
C-N

Quote:

Originally Posted by emoners

@C-N: seems like you're enjoying this board :D

Oh yes its a nice piece of work 4 sure worth the wait to get everything so spot on.

Quote:

Originally Posted by zsamz_

nice verry nice the scores are not far off the ut p35
it has the best bandwidth i seen in 45 if dfi doesnt drop the ball it can be better than the ut p35 in 6 months
tks C_N

Its right up there with the P35 for me already, I just wish I had a q9650 to really give her some stick.

Quote:

:mad:you givin me the itch for another dfi board

:rolleyes: :hehe:

Quote:

Originally Posted by DJSUB

wow very nice result c-n :D
i'm gonna buy this board :up:

He he you don't mess about do ya, see you on the track mate :D

Quote:

Originally Posted by radaja

@c-n, those everest scores look awesome! think i might get this board soon!

You cant go wrong just dial it in & it works.

CN :)
11-03-2008, 06:44 AM
DJSUB

Quote:

He he you don't mess about do ya, see you on the track mate

i'm waiting for that ut p45 for a long time but unfortunately lanparty jr is the 1st one arrive. i already sell my p45 JR and now it's time for the UT P45 :D :up:
11-03-2008, 08:30 AM
bito

Looking forward to Q9650 on this 'board vs Maximus II :D
11-03-2008, 01:12 PM
C-N

E8500 @ 4.5GHZ DDR1186 9.5H Prime Blend Stable

Got round to running 1 loop of Prime blend today, same 3D, Everest as before.

CN :)

======

DFI LANPARTY UT P45-T2RS (BIOS 1007)

INTEL CORE 2 DUO E8500 WOLFDALE 3.16GHZ 6M L2 CACHE (Q807A273 / C0)

OCZ PC2-8500 SLI 2 x 1GB PN:OCZN1066SR2GK

GECUBE HD4870X2 1GB (8.11 BETA DRIVERS)

1 X HITACHI DJ 80GB HD'S

SONY DUAL LAYER DVD RW (DRU-820A)

OCZ GAMEXTREAM 700W PSU

WINDOWS XP PRO SP3

CPU COOLING: WATER 1/2" TUBING, D-TEK FUZION V1 (4.5MM NOZZLE), LAING D5 VARIO, PA130.3, 3 X 100CFM PANAFLO 120MM FANS

Code:

>CPU Feature: Thermal Management Control.......... - Disabled PPM(EIST) Mode...................... - Disabled Limit CPUID MaxVal.................. - Disabled CIE Function........................ - Disabled Execute Disable Bit................. - Disabled Virtualization Technology........... - Disabled Core Multi-Processing............... - Enabled >DRAM Timing: Enhance Data transmitting........... - Fast Enhance Addressing.................. - Fast T2 Dispatch......................... - Auto >Clock Setting Fine Delay Press Enter: DLL And RCOMP Settings.............. - Auto Ch1 Dram Defaul Skew................ - Model 3 Ch2 Dram Defaul Skew................ - Model 3 RCOMP Settings...................... - Model 1 Fine Delay Step Degree.............. - 70ps Ch1 Clock Crossing Setting.......... - Nominal DIMM1 Clock Fine Delay.............. - Current[2396ps] DIMM2 Clock Fine Delay.............. - Current[2396ps] Ch1 Control0 Fine Delay............. - Current[268ps] Ch1 Control1 Fine Delay............. - Current[268ps] Ch1 Control2 Fine Delay............. - Current[268ps] Ch1 Control3 Fine Delay............. - Current[268ps] Ch1 Command Fine Delay.............. - Current[394ps] Ch2 Clock Crossing Setting.......... - Nominal DIMM3 Clock Fine Delay.............. - Current[2066ps] DIMM4 Clock Fine Delay.............. - Current[2066ps] Ch2 Control0 Fine Delay............. - Current[48ps] Ch2 Control1 Fine Delay............. - Current[48ps] Ch2 Control2 Fine Delay............. - Current[48ps] Ch2 Control3 Fine Delay............. - Current[48ps] Ch2 Command Fine Delay.............. - Current[394ps] Ch1 Ch2 Common Clock Setting........ - More Aggressive Ch1 RDCAS GNT-Chip Delay............ - Auto Ch1 WRCAS GNT-Chip Delay............ - Auto Ch1 Command To CS Delay............. - Auto . Ch2 RDCAS GNT-Chip Delay............ - Auto Ch2 WRCAS GNT-Chip Delay............ - Auto Ch2 Command To CS Delay............. - Auto Flex Memory Mode..................... - Auto CAS Latency Time (tCL)............... - 5 RAS# to CAS# Delay (tRCD)............ - 5 RAS# Precharge (tRP)................. - 5 Precharge Delay (tRAS)............... - 10 All Precharge to Act................. - 5 REF to ACT Delay (tRFC).............. - 28 Performance Level.................... - Auto >Read delay phase adjust Press Enter: Channel 1 Phase 0 Pull-In........... - Auto Channel 1 Phase 1 Pull-In........... - Auto Channel 1 Phase 2 Pull-In........... - Auto Channel 1 Phase 3 Pull-In........... - Auto Channel 1 Phase 4 Pull-In........... - Auto Channel 2 Phase 0 Pull-In........... - Auto Channel 2 Phase 1 Pull-In........... - Auto Channel 2 Phase 2 Pull-In........... - Auto Channel 2 Phase 3 Pull-In........... - Auto Channel 2 Phase 4 Pull-In........... - Auto Write to PRE Delay (tWR)............ - 12 Rank Write to Read (tWTR)........... - 11 ACT to ACT Delay (tRRD)............. - 3 Read to Write Delay (tRDWR)......... - 8 Ranks Write to Write (tWRWR)........ - Auto Ranks Read to Read (tRDRD).......... - Auto Ranks Write to Read (tWRRD)......... - Auto ALL PRE to Refresh.................. - Auto >Voltage Settings: CPU VID Control..................... - 1.53125V CPU VID Special Add................. - Disabled CPU VID Special Add................. - Auto DRAM Voltage Control................ - 2.21v SB Core/CPU PLL Voltage............. - 1.55v NB Core Voltage..................... - 1.369v CPU VTT Voltage..................... - 1.24v Vcore Droop Control................. - Enabled Clockgen Voltage Control............ - 3.60v GTL+ Buffer Strength................ - Strong CPU GTL 0 REF Volt.................. - 0.6225 CPU GTL 2 REF Volt.................. - 0.6225 CPU GTL 1 REF Volt.................. - 0.6225 CPU GTL 3 REF Volt.................. - 0.6225 North Bridge GTL 0 REF Volt......... - 0.6275 North Bridge GTL 1 REF Volt......... - 0.6275 FSB Vref............................ - Auto Genie BIOS Settings: Exist Setup Shutdown................ - Mode 2 Exist Shutdown After AC loss........ - Enabled AC Shutdown Free.................... - Enabled O.C Clock Fail Retry Counter........ - 0 O.C Clock Fail CMOS Reloaded........ - Disabled CPU Clock Ratio..................... - 9.5 Target CPU Clock.................... - 4493MHz CPU Clock........................... - 473 Boot Up Clock....................... - Auto CPU Clock Amplitude................. - 800mV CPU Clock0 Skew..................... - 200ps CPU Clock1 Skew..................... - 0ps DRAM Speed.......................... - 266/667 Target DRAM Speed................... - 1186MHz PCIE Clock.......................... - 100mhz PCIE Slot Config.................... - 1x 1x CPU Spread Spectrum................. - Disabled PCIE Spread Spectrum................ - Disabled

PRIME95 + 3x CPU-Z

http://i106.photobucket.com/albums/m...86/95HStop.jpg

EVEREST CACHE & MEMORY:(READ 10480MBS LATENCY 48.5NS)

http://i106.photobucket.com/albums/m...45266Strap.jpg

3DMARK2001:(SCORE 87004)

http://i106.photobucket.com/albums/m...6/3DMARK01.jpg

3DMARK2003:(SCORE 82125)

http://i106.photobucket.com/albums/m...6/3DMARK03.jpg

3DMARK2005:(SCORE 30424)

http://i106.photobucket.com/albums/m...6/3DMARK05.jpg

3DMARK2006:(SCORE 21432)

http://i106.photobucket.com/albums/m.../3dDMARK06.jpg

AQUAMARK 3:(SCORE 268,526)

http://i106.photobucket.com/albums/m...6/Aquamark.jpg

SHORT DESCRIPTION:
473 x 9.5 = 4500MHz @ 1.45v
5-5-5-10 2T @ 2.21V DDR 1186
11-03-2008, 01:22 PM
Sumanji

Would this be a better board to get over the DFI X48?

It seems to be about £30 more and not sure why...
11-03-2008, 01:49 PM
politenessman

its more than the lp dk x48, but not the lt or ut. i had that board (dk x48) several months ago and was not impressed. i guess the extra cost is for the digital pwm, the extra pcie "16" slot and the extra bundle. i just got my ut p45 from newegg an hour ago, and had a little trouble getting it to run dual channel, but figured it out. had the tpower the last few months and it took a few minutes to get used to fine granulation on the voltage and working with a decent selection of straps/dividers. i ordered this board after newegg had it for sale less than an hour, and guess what, it had been used. scratches on the heat sinks and the metal frame that clamps on the socket, plastic bags openned and scotch taped(!!) shut, bios settings saved on the "cmos loaded" slots, etc. somebody in the warehouse must have taken it home for a day or 2 and/or set it up in the warehouse. i will check everything out and see if it worx before i decide to send it back or not. seems like a nice board, not as easy and flat out spectacular as the ut p35, but has potential. will start posting some results tonight with my average e8500 c0, another coming tomorrow, maybe e0, and a q9550 the day after that.

thanx for the bios settings, c-n.

edit i checked and this board is actually $10 less than the dk x48 t2rs, and $30 less than the dk t2rsb.
11-03-2008, 02:28 PM
SNiiPE_DoGG

I guess this is good because now I have a backup board if the Avenger is indeed not released :D

Is there going to be a ddr3 revision of this board??????? if so then CHA-CHING $$$ jackpot :D
11-03-2008, 03:36 PM
zsamz_

Quote:

Originally Posted by Sumanji

Would this be a better board to get over the DFI X48?

It seems to be about £30 more and not sure why...

actually the ut p35 is better than the dfi x38-x48
and this board lookin better than the x48 so far
in my book its worth more than the x48;)
11-03-2008, 06:04 PM
Clunk

Started a Living Review here, I'll update here with my findings tomorrow :)

Click image for full size, high resolution.

http://www.images.clunk.org.uk/revie...45-t2rs-sm.jpg

http://www.images.clunk.org.uk/revie...s/IMG_5912.jpg

:up:
11-04-2008, 12:51 AM
C-N

Quote:

Originally Posted by Clunk

Started a Living Review here, I'll update here with my findings tomorrow :)

Very very nice work Clunk :up:, looking forward to your results.

I'll add the link to the first post if thats ok.

CN :)

P.S I must go sign up at your place :D
11-04-2008, 06:59 AM
Clunk

Thanks mate, looks like a great board so far, I'm interested to know what it'll make of this E8600. :up:
11-04-2008, 08:25 AM
RNeon

Quote:

Originally Posted by C-N

I put up some BIOS screen shots on the 1st page.

Here are a couple of Everest Cache & Memory benches, The first is just something I happened to run last night & the second is where I think I will be able to run daily & complete a loop of Prime.

http://i106.photobucket.com/albums/m...yBenchmark.jpg

http://i106.photobucket.com/albums/m...45266Strap.jpg

I have also attached a tweaked Smartguardian skin free for anyone that wants it.

CN :)

Hello,

how can i get to work this smart guardian?
11-04-2008, 08:50 AM
BiTsCrEaM

Download the skin, unzip it (if it's zipped, IDRC), drag into proper Smartguardian folder (something along the lines of skins etc. will check for sure later as my main PC is down ATM).
11-04-2008, 08:51 AM
C-N

Quote:

Originally Posted by RNeon

Hello,

how can i get to work this smart guardian?

Download the RAR & unpack it, Close SG, Copy & paste the background & smart.ini into the ITE/SG folder then re open SG.

CN :)
11-04-2008, 09:00 AM
RNeon

there are 3 files alle the three i have to copy it in the sm folder? and wich version do you mean ? and how do coretemp run over smart guardian. im sorry io dont understand.
11-04-2008, 09:16 AM
RNeon

PLease help me i don´t understand how did you made it. i have copied the bachground and the smart.ini but i have a too small window and the coretemp window is not included. wich version of smart guardian i have to use?
11-04-2008, 09:22 AM
BiTsCrEaM

Copy them into the ITE/SG folder.
11-04-2008, 09:28 AM
RNeon

yes i´ve done it from the first time and it looks like this.

http://www.abload.de/thumb/smartohhq.jpg

it is not complete. wich version i need from smart guardian? and how can i input the coretemp in it?
11-04-2008, 09:34 AM
C-N

Quote:

Originally Posted by RNeon

there are 3 files alle the three i have to copy it in the sm folder? and wich version do you mean ? and how do coretemp run over smart guardian. im sorry io dont understand.

Quote:

Originally Posted by RNeon

PLease help me i don´t understand how did you made it. i have copied the bachground and the smart.ini but i have a too small window and the coretemp window is not included. wich version of smart guardian i have to use?

No just the background & the .ini file the other image is just to show you it was made the same size as core temp. Just run SG & put it next to SG.

What OS are you using I have tested it with XP 32bit SP2 & 3 AND Vista 32bit & SP1 & not had any problems.
11-04-2008, 09:38 AM
RNeon

im running vista 64bit but how can i make the window normal? you can see in the pic that it is not complete on the left side. In the SG folder there are 3 backgorund files at default should i let it so?
11-04-2008, 09:55 AM
RNeon

and wich rams 2x2gb do you prefer fpr this board and good overclocking? need rams that make 1200mhz stable
11-04-2008, 10:03 AM
RNeon

ok i solve the problem by myself. you need the SG Version from the DK P45 T2RS and not for the new. I installed it and it runs. but please answer my question about the rams. thank you:)
11-04-2008, 10:44 AM
C-N

Quote:

Originally Posted by RNeon

ok i solve the problem by myself. you need the SG Version from the DK P45 T2RS and not for the new. I installed it and it runs. but please answer my question about the rams. thank you:)

Oh I thought they were the same version but I'm glad you got it working :up:

Sorry I only have 2 OCZ Reaper 4GB sets one PC2-6400 that will do 1130 ish mhz in other boards & one PC2-8000 kit. I'm not sure how far the 8000 kit will go as I've never realy benched them all I do know is I don't have a 4GB kit that will do 1200mhz. Have you checked the memory list on the 1st post or the DFI site, perhaps that will help.
11-04-2008, 12:23 PM
MTP04

Bought this board earlier today, should arrive before the weekend.:D

I'll share some results once I have some.
11-04-2008, 03:14 PM
politenessman

i am unable to get either of my 2gb kits of ocz ddr2 1150 to post in this board in any way. single channel, dual channel, single stick, any dimm, gets me c1 error. my 2gb ddr2 1066 tracer runs fine, as does my 2gb adata 6400 and old g.skill hz. 4gb g.skill 1066 pi coming tomorrow with e0 q9550.
11-04-2008, 03:58 PM
kitfit1

Quote:

Originally Posted by politenessman

i am unable to get either of my 2gb kits of ocz ddr2 1150 to post in this board in any way. single channel, dual channel, single stick, any dimm, gets me c1 error. my 2gb ddr2 1066 tracer runs fine, as does my 2gb adata 6400 and old g.skill hz. 4gb g.skill 1066 pi coming tomorrow with e0 q9550.

I find that very odd. I have 4x1gb OCZ PC9600 Flex's in mine and they boot up fine, even from a straight Cmos clear. I would of thought 4 sticks are less likely to boot than anything.
11-04-2008, 04:34 PM
emoners

@C-N or Clunk: have you guys tried slapping a quad on this board?
11-04-2008, 04:59 PM
politenessman

i will have q9550 e0 in tomorrow (wed) and post results.
11-04-2008, 11:50 PM
C-N

Quote:

Originally Posted by emoners

@C-N or Clunk: have you guys tried slapping a quad on this board?

Sorry I haven't, I don't own one & its driving me nuts. I guess I'll will have to sell some stuff off & get one.

Quote:

Originally Posted by politenessman

i will have q9550 e0 in tomorrow (wed) and post results.

I Look forward to your results :up:
11-05-2008, 11:39 AM
C-N

I dusted of my old SS last night & gave her a bit more stick :D

560fsb is where all the action is on my board ;)

http://i106.photobucket.com/albums/m...ncy5625X95.jpg
11-05-2008, 03:49 PM
zsamz_

1 Attachment(s)

Quote:

Originally Posted by C-N

I dusted of my old SS last night & gave her a bit more stick :D

560fsb is where all the action is on my board ;)

http://i106.photobucket.com/albums/m...ncy5625X95.jpg

lookin good
this is best i did with ut p35
11-05-2008, 04:05 PM
C-N

Its pretty close, this is the closest bench I have to 565 x 8.5

http://i106.photobucket.com/albums/m...che/560x85.jpg

I also pulled a couple more fsb out, still a couple off my P35 but an improvement.

http://i106.photobucket.com/albums/m.../MaxFSB625.jpg
11-05-2008, 04:05 PM
SNiiPE_DoGG

Quote:

Originally Posted by zsamz_

lookin good
this is best i did with ut p35

his cache numbers are quite a bit higher than yours... is this a result of the p45?
11-05-2008, 04:09 PM
C-N

Quote:

Originally Posted by SNiiPE_DoGG

his cache numbers are quite a bit higher than yours... is this a result of the p45?

Core speed would be my guess, look at my closer nearly like for like bench.
11-05-2008, 04:11 PM
SNiiPE_DoGG

Quote:

Originally Posted by C-N

Core speed would be my guess, look at my closer nearly like for like bench.

:doh: lol I forgot to look at that :rofl::rofl::rofl::ROTF:
11-05-2008, 04:32 PM
zsamz_

Quote:

Originally Posted by SNiiPE_DoGG

his cache numbers are quite a bit higher than yours... is this a result of the p45?

i'm on air i cant go that high on cpu:rofl:
11-05-2008, 05:12 PM
namegt

nice "C-N"
DFI UT P45 T2RS
your settings for 600fsb?
11-05-2008, 05:35 PM
namegt

DFI Lanparty UT P45-T2RS 10/28 BIOS

http://namegt.tistory.com/attachment...13e76597BU.zip
11-05-2008, 05:38 PM
namegt

http://cfs12.tistory.com/image/18/ti.../491039c495615
http://cfs15.tistory.com/original/26.../49106a2d573ba
DFI UT P45 T2RS my first post

Unstable and difficult to raise the BIOS FSB
11-05-2008, 06:28 PM
BlazingArrow

OMG! That's not a glitch, it's running @ 1.2 vCore????
11-05-2008, 11:45 PM
politenessman

got my q9550 e0 today and stoked it up in the ut p45. absolute nightmare. unstable even at default, random power downs, bsod, black screens. checked cpu in another mainboard and it (q9550) is fine. checked my e8500 e0 in the p45 and it (lp ut p45) was fine. looks like these boards may ( or my board, at least) have issues with 45nm quads, or 45nm quad e0. its in the machine now and this is the third time i am trying to post this, it keeps on bsod'ing or random warm restarting. i ahve been over it and over it since 4pm. its about 2:40am now.
tried 4 types of ram, another psu, still ng. anybody else have a 45nm quad on this board?

Show 100 post(s) from this thread on one page