Printable View
Hiya guys,
You can have a look at the whole project at coolercases... http://coolercasesuk.co.uk/showthread.php?t=3575
I will post the whole project here soon.
just finished cleaning all the paste off my nb/sb, so i thought i's see what it'll look like with all the EK blocks on, so here u go......
Looks awesome.....:party:
When did that SB cooler come out?
Looks good. Yes that SB? looks like, much longer than the others..
Also i see you run a qx6700
Looking ,when you are finished with your build, forward to have your bios settings here
http://www.xtremesystems.org/forums/....php?p=2727832
Thanks :)
And thanks to Eddy :)
I think Eddy released it last week sometime, i only saw it by luck - and ordered there and then
Very sexy. I admit EK blocks always look great and I have 4 on mine (FB8800, NB Asus 3, 2x Mosfets Asus 3). If the EK Supreme isn't restrictive, I would have a full EK setup for sure.
this build will have the same 8800GTX KO with an EK block as my sig - and it has a black PCB so it'll all look great in the end. Which is why i sprayed the Fuzion mounting plate black.
but this will only have an e6850, coz i'm going to build another quad in another silverstone TJ07.For sure if the supreme wasn't so restrictive i would have gone EK all round too.
Very nice..
How is the fit on your block?
Were you able to fit a screw through the middle hole from underneath?
Did you use a TIM pad or paste for the SB chip?
they're not actually mounted yet - just placed on to make sure the sb block fitted right. But i'll be using MX-2
But the fit is perfect from what i can tell atm
I found that the two mounting holes in the acrylic were good, but that the threaded hole in the copper underneath was not aligned.
Please check yours to see if the screw hole in the bottom is aligned or if it's off.. Thanks.
no, mine doesn't line up, but i'm not sure if it'll make alot of difference as there wasn't a screw there anyway (on the original block).
But i'll re-check it all tomorrow or monday when i actuall mount it all.
Yeah, the original block had tension at 4 different points.
EK put the middle screw hole there for tension across the SB chip.. not sure how critical that really is.
I did notice a gap about the thickness of a paper business card between the block and the SB chip.
Gap is a few tenths of a mm, so I'm thinking paste or TIM should do.
I'll ask Eddy about it when he gets back from Cebit.
from what i can tell, so far mine sits perfectly, no gap or anything
Cut a strip of paper or card stock and try to fit it in like this:
http://www.moschini.org/EK-SBMaxExGa...Test-large.JPG
I cut a strip of a business card paper, which was 0.3 mm thick.
I can fit it in just over the left side of the SB chip, but it's a tight fit on the right side.
I'm not sure if 0.3 to 0.5 mm of gap is really all that critical or not, but it would be good to see.
I wasn't able to fit the strip on the left hand side of the block where the silver Crosslinx chip is, so that's a good fit there.
Huhmm looking at the block with the acrylic top it appears the lower left and upper right corners are not covered. I wonder how that will effect performance.
Probably not enough to matter.. there's quite a lot of copper mass on top.
Yes, it doesn't matter a lot since there is still enough surface to cool it.
Are u or have u ran that with that gap? Giuliano?
If so what temps were u getting?
Thanks
Haven't run it yet. :)
Using the longer screws with the spring mounts seems to be a bit better.. less of a gap.
Once EK fixes the alignment of the screw hole underneath - either by a different top or a fixed bottom - then the gap should be eliminated.
For now, I just put on a glob of AS5 to make sure it spreads out.
Hiya Guys,
i just thought i'd post a couple of pics now i have mounted all the blocks...
Gawd, i just dont like those big thumbscrews-nut-or-watherver-you-call-em thingys that EK uses...
also, i wish they move away from that puke green washers too...
just some personal OCD kickin in...
where did you find the mosfets
I went straight to source....
http://ekwaterblocks.com/shop/index....013f54428b8c2c
On most of the latest nb/sb blocks they're underneath the mobo so u don't see them.Quote:
Originally Posted by kinghong1970
As for the green washers - surely there must be black ones?
the SB and mosfet does not put out much heat right? does it really need to be water cooled or are you doing this just because this is XS?
Very nice. I have all the exact same blocks and board...lol. I was wondering if anyone had any trouble fitting video cards around the south bridge block. I am still modding the case and did not fit a video card in yet but by the looks of it the top video slot is going to have trouble if I try to stick a 9800Gx2 in there. Should I just go with a water cooled 3870X2?
I could not mount my 3870X2 with the stock cooler on it because of the sb block, but with the EK X2 block it works great! (hey thats marketing for ya)Quote:
Originally Posted by Sadasius
also yes my screwlines up with the hole underneath, be there are 2 holes on my sb max ex. and it fits in the one closer to the sb chip, but it does work, I had to fiddle with it, and now there is no gap what so ever.Quote:
Originally Posted by Giuliano
Okay I guess it is the 3870X2 then with a waterblock. I will go with EK for that for sure. Might as well keep it consistent huh! I think I am going to try out the new koolance 45 degree swivel to see if I can have all 1/2" compression fittings as well to keep kinks out of the way. I tried it all with the supplied barbs and have only one slight kink but that's not good enough for me so back to the drawing board.
Here is the swivel linky;
http://www.performance-pcs.com/catal...ducts_id=23846
I wonder if these will hamper flow too much. These things look to be a life saver in many areas for my loop especially if I can use compression fittings on the Fuzion, SB and NB blocks. Not to mention less likelihood of kinks.