How to overclock FSB to 550MHz on P5B-Deluxe

Test Configuration:

CPU: Intel Conroe Core 2 Duo E6300 1.86G
Memory: CORSAIR CMX1024-9600C5
GeIL PC2-6400 GX22GB6400PDC

H/W changes: High FSB needs high Chipset core voltage

http://www.iamxtreme.net/andre/P5B-Mod/01.jpg


Decrease the resistor value will increase Chipset core voltage.
For example:

http://www.iamxtreme.net/andre/P5B-Mod/06.JPG

To get above voltages, you should select the “NB Vcore� item to “1.65V� in BIOS Setup Utility.



BIOS setting recommendation :

http://www.iamxtreme.net/andre/P5B-Mod/02.jpg

Over-Voltage Recommendation

http://www.iamxtreme.net/andre/P5B-Mod/03.jpg

CPU-Z information

http://www.iamxtreme.net/andre/P5B-Mod/04.jpg

Super PI 2M finished

http://www.iamxtreme.net/andre/P5B-Mod/05.jpg




Thanks your reading.:)

Sweet! So we put a 5k VR on that resistor and lower the resistance to get more vNB?

Good tip, Andre. And very nice results.:slobber:

Quote:

---

Originally Posted by 5-Clicks

Sweet! So we put a 5k VR on that resistor and lower the resistance to get more vNB?

---

Maybe change SMD ohm is perfect.:)

:banana::banana::banana::banana: man that's very good

anyone else aside from you and sierra with these results or what

very nice, I may be trying this out tonight:p:

what is the FSB limit without doing the mod?

Quote:

---

Originally Posted by 5-Clicks

Sweet! So we put a 5k VR on that resistor and lower the resistance to get more vNB?

---

I ask my friend, you are right. You can put 5K VR on that resistor.:)

Quote:

---

Memory: CORSAIR CMX1024-9600C5

---

huh?

Quote:

---

Originally Posted by Kunaak

huh?

---

ES:D

Quote:

---

Originally Posted by AndreYang

ES:D

---

nice mod andre. Sure beats the heck out of the gigabyte with bios voltage options that dont do anything.


DQ6-

1.6+ VCORE, fail to post

.25+MCH, fail to get past 475FSB wall. System loses total stability.

Quote:

---

Originally Posted by AndreYang

ES:D

---

well that may have something to do with it. :D

Cool, but what is safe 24/7 voltage?

wow nice find m8... :)

May have to get one now... ordered a DS3 if its a "crapper" i'll go for the P5B dlux...

TY...

Quote:

---

Originally Posted by Kallenator

Cool, but what is safe 24/7 voltage?

---

Dual Prime 95 5 hours is no problems , but I am not sure 7/24 in the case.

This mod should be available on any 965P board, yes? Including the DS3?

Quote:

---

Originally Posted by 5-Clicks

This mod should be available on any 965P board, yes? Including the DS3?

---

Maybe it's different because layout is different.

Quote:

---

Originally Posted by AndreYang

http://www.iamxtreme.net/andre/P5B-Mod/06.JPG

---

Are these inline measurements or desoldered components?

Thx Andre!
I think change asus p5w dh..

Quote:

---

Originally Posted by AndreYang

Test Configuration:
Memory: CORSAIR CMX1024-9600C5

---

How do you get such memory ?

any validation link andre ?

Quote:

---

Originally Posted by AndreYang

Maybe it's different because layout is different.

---

Yeah, I didn't mean to say that you can do this exact mod on a DS3, but the resistor in the pic that you circled above is probably on a DS3 or any other 965P board...we just have to find it :D

Is this pencil moddable? Where's the read point? 550 fsb would be PERFECT with an E6400 on dry ice and in my price range :D

Incredible...

:slobber:

Nice work AndreYang!:clap:
This mobo is very interesting...What do you think of these mobo?

Marco:)

Follow Andre's Over-Voltage Recommendation, I got FSB552:D

Quote:

---

Originally Posted by tanghiro

Follow Andre's Over-Voltage Recommendation, I got FSB552:D

---

:woot: now up the multi and let's see some results!!! please please:D

The king is dead, long live the king ?

The fsb has now been overclocked by over 100% :guitar:

this mod is NOT for the faint hearted...you will need a huge magnifying glass, steady hand, low power soldering gun and a LOT of courage:D

So a bit of conductive paint/pen isnt going to work out then :D

Quote:

---

Originally Posted by Ace-a-Rue

this mod is NOT for the faint hearted...you will need a huge magnifying glass, steady hand, low power soldering gun and a LOT of courage:D

---

Plz this mod is not so hard. All you need is to solder a wire to the resistor. Now if you would need to solder a wire to a small pin it could be chalenging. I only solder to the pin if there is no alternative. Usualy i try to search for continiuty from the pin to resistor and solder to resistor instead. Anyone with basic soldering skills and $8 low power soldering iron can do this mod;)

you are a better man than me...i am not a good solderer

lol get a junk MB and start to practice. I could not solder before ether.... In 2-3 days you will get comftible with iron and this mod will not scare you anymore :)

AndreYang, can you post results for vMCH 1.65(unmodded, maximum in BIOS) on this board?

Hi AndreYang & tanghiro

I'm still waiting on my P5B Dlx.

Two quick questions please

( i ) Can you please post a picture of the completed mod ?

( ii ) Can you please advise the highest FSB you can get when using
just 1.65v for the MCH ?

[ Reason I ask is that BIOS 0507 allows MCHv up to 1.65, so for those of us that are poor / shaky solderer's, I'm wondering how high a FSB 1.65v will get us ? ]

Many thx,
Ben.

Are the OC-abilities with a “Asus P5B Deluxe WiFi� limited? Because of the WiFi?

Quote:

---

Originally Posted by tanghiro

Follow Andre's Over-Voltage Recommendation, I got FSB552:D

---

Please try higher multi!
Thx

This looks better and better people but I got to ask again, What is 24/7 safe MCHv?

I haven't done the mod yet but 6x500 is benchable, but 7x500 is not :( even though 3500MHz is fine at lower FSB.

P5B-Deluxe
TT Blue Orb
Gskill64002GBHZ
MCH = 1.45v

http://www.users.on.net/~bugeyes/ind...20copy%202.jpg

Is it any difrence in max FSB on Asus P5B and the deluxe version ??
Is this mod working on Asus P5B ?

Nice Andre and tanghiro :), I'm sure it's possible to reach 550 and more with no mods and 24/7 rock stable around 510-520 ;)

soon... :D

Quote:

---

Originally Posted by tanghiro

Follow Andre's Over-Voltage Recommendation, I got FSB552:D

---

AGP x1? :hm:

Nice info! :)

Quote:

---

Originally Posted by cpulloverclock

Nice Andre and tanghiro :), I'm sure it's possible to reach 550 and more with no mods and 24/7 rock stable around 510-520 ;)

soon... :D

---

agree with you cpull :D

Do these mods work on P5B non deluxe too ??

Quote:

---

Originally Posted by bugeyes

I haven't done the mod yet but 6x500 is benchable, but 7x500 is not :( even though 3500MHz is fine at lower FSB.

---

I dont get it .You have retail 6600 and you can change multy downwards to 7? Didnt know its possible i thought only ES have lower multy option.

I'm not at all good at hard-mods, and now 0507 supports up to 650mhz BIOS NOW!

http://img123.imageshack.us/img123/2759/image1li8.jpg

Quote:

---

Originally Posted by Moonraker™

I'm not at all good at hard-mods, and now 0507 supports up to 650mhz BIOS NOW!

---

LOL I got that board to my server multimedia station :rolleyes: .

I've just ordered it. Can't be arsed waiting for 590 SLi and this board looks far too good to turn down.

Quote:

---

Originally Posted by railer

I dont get it .You have retail 6600 and you can change multy downwards to 7? Didnt know its possible i thought only ES have lower multy option.

---

It is possible with retail, too. You just can't change it upwards; and even downwards, it's just a step or two.

Quote:

---

Originally Posted by railer

I dont get it .You have retail 6600 and you can change multy downwards to 7? Didnt know its possible i thought only ES have lower multy option.

---

Only with the later bioses, I think it has to do with Intels speedstep tech (cool-n-quiet)

Quote:

---

Originally Posted by bugeyes

Only with the later bioses, I think it has to do with Intels speedstep tech (cool-n-quiet)

---

what was your board max withprevious bioses

you on E6600 yeah?

Quote:

---

Originally Posted by dinos22

what was your board max withprevious bioses

you on E6600 yeah?

---

bios 0405 multies locked FSB to 500MHz
bios 0507 multies unlocked FSB to 650MHz ( bit of a joke that..505 is the max I could get unmodded)

http://www.users.on.net/~bugeyes/ind...505%20copy.jpg

i'm asking you how much your max OC changed from first bioses to the latest ones

Quote:

---

Originally Posted by dinos22

i'm asking you how much your max OC changed from first bioses to the latest ones

---

Max OC for that retail E6600 has not changed from 3.6GHz using later bioses, however when approaching 500MHz FSB max cpu clocks do reduce, as to what level I have not determinded.

Can I see a pic of the motherboard after the mod is done

Quote:

---

Originally Posted by bugeyes

Max OC for that retail E6600 has not changed from 3.6GHz using later bioses, however when approaching 500MHz FSB max cpu clocks do reduce, as to what level I have not determinded.

---

max FSB OC i should say sorry

Quote:

---

Originally Posted by dinos22

max FSB OC i should say sorry

---

shipping bios I could max out at 400MHz, 0405 I could max out at 400MHz (limited by locked multies), 0507 will only give me 505MHz though I'm sure it will go higher if I get rid of the N/B passive heatpipe.

I change my order from ds4 to p5b-dlx . :D Nice thread - info

TAKE TWO

Hi AndreYang & tanghiro - re-posting as a few of us here are asking / awaiting this info

( i ) Can either of you please post a picture of the completed mod ?

( ii ) Can you please advise the highest FSB you can get when using
just 1.65v for the MCH ?

Many thx,
Ben.

Quote:

---

Originally Posted by bugeyes

shipping bios I could max out at 400MHz, 0405 I could max out at 400MHz (limited by locked multies), 0507 will only give me 505MHz though I'm sure it will go higher if I get rid of the N/B passive heatpipe.

---

You reckon that the NB is that bad then?

I was thinking of replacing it with the TT Extreme Spirit II. and leaving the voltage heaty's on. Using silver as the compound. on both. Sawing the bar off in between them.

Quote:

---

Originally Posted by bugeyes

shipping bios I could max out at 400MHz, 0405 I could max out at 400MHz (limited by locked multies), 0507 will only give me 505MHz though I'm sure it will go higher if I get rid of the N/B passive heatpipe.

---

yeah that's what i was getting at

hmmmmmmmmmmmmmm what to do now heheheh get an asus as well me thinks heh

Quote:

---

Originally Posted by dinos22

yeah that's what i was getting at

hmmmmmmmmmmmmmm what to do now heheheh get an asus as well me thinks heh

---

ah the sickness :D

Quote:

---

Originally Posted by ben ifin

TAKE TWO

Hi AndreYang & tanghiro - re-posting as a few of us here are asking / awaiting this info

( i ) Can either of you please post a picture of the completed mod ?

( ii ) Can you please advise the highest FSB you can get when using
just 1.65v for the MCH ?

Many thx,
Ben.

---

Could you plz post the info requested above as im about to order two of these bords for new setups paired with E6400's and TEAMgroup DDR2 5300 kits, but still don't see how exactly to do the mod.

-What voltage for MCH did you guys use to get 550fsb ?
- could you please post pics of a more general (zoomed) out view, as the only pics i have seen show a wire or two attached to the resistor, not an overall view of the completed circuit?

Here is my elite image manipulation for 1.65V :banana:, is it right at all ?

http://img413.imageshack.us/img413/4527/modil4.jpg

My soldering skills are good but im not sure exactly what to do yet, and i think some other people need help understanding too.

Thanks very much lads :toast:

Quote:

---

Originally Posted by adfinni

Could you plz post the info requested above as im about to order two of these bords for new setups paired with E6400's and TEAMgroup DDR2 5300 kits, but still don't see how exactly to do the mod.

-What voltage for MCH did you guys use to get 550fsb ?
- could you please post pics of a more general (zoomed) out view, as the only pics i have seen show a wire or two attached to the resistor, not an overall view of the completed circuit?

Here is my elite image manipulation for 1.65V :banana:, is it right at all ?

http://img413.imageshack.us/img413/4527/modil4.jpg

My soldering skills are good but im not sure exactly what to do yet, and i think some other people need help understanding too.

Thanks very much lads :toast:

---

CAL930 posted another way to mod the vMCH in a thread about the Asus P5B Deluxe

http://home.hccnet.nl/J_Bongers/P5B/P5BVMCHMOD.jpg
20kΩ～50kΩVR

Maybe easier to do this version of the mod

click to view CAL930's post

Quote:

---

Originally Posted by Jmax_oc

Quote:

---

Originally Posted by AndreYang

Test Configuration:
Memory: CORSAIR CMX1024-9600C5

---

How do you get such memory ?

---

Can we have some informations about it ?

Quote:

---

Originally Posted by Moonraker™

You reckon that the NB is that bad then?

I was thinking of replacing it with the TT Extreme Spirit II. and leaving the voltage heaty's on. Using silver as the compound. on both. Sawing the bar off in between them.

---

No I don't think it's bad at all... 266MHz out to 500MHz thats pretty good, I'm just trying to make the point that as I got to 500MHz @ 1.45v to the N/B any more volts gained nil mhz, that could and I stress the word could mean heat is a factor.

I wouldn't be sawing anything in half, particularly your mobos heatpipe, leave it be, but if your a compulsive tinkerer, remove it and replace with whatever, buy some ram sinks for power mosfets.

another VMCH modded.

http://www.iamxtreme.net/andre/P5BD-MCH.jpg

Hi AndreYang

How high a FSB were you getting with just 1.65v in the MCH ?

Ben

I presume this resistor is suitable:

http://www.maplin.co.uk/Module.aspx?...=SEO&U=strat15

Then solder the relevent pins (leaving the top one unconnected ?)

Once installed do you incease its resistance to max then turn it down until the voltage measured goes up to 1.65V ????

thanks

Hi AndreYang :)

P5B-Deluxe
The ClockGen Tools use it is possible.?

Quote:

---

Originally Posted by jmax_oc

Quote:

---

Originally Posted by Jmax_oc

Quote:

---

Originally Posted by AndreYang

Test Configuration:
Memory: CORSAIR CMX1024-9600C5

---

How do you get such memory ?

---

Can we have some informations about it ?

---

Is it possible to know how to you get such sample memory ? :stick:

Does this board allow for high ratios like 4:3 ?

Quote:

---

Originally Posted by OC_Windforce

Hi AndreYang :)

P5B-Deluxe
The ClockGen Tools use it is possible.?

---

P5B Deluxe didn't support ClcokGen and setFSB yet.

Quote:

---

Originally Posted by 775911

Does this board allow for high ratios like 4:3 ?

---

P5B Deluxe 4:5 has some problems. You need to use 1:1 or 2:3.:)

Quote:

---

Originally Posted by ben ifin

Hi AndreYang

How high a FSB were you getting with just 1.65v in the MCH ?

Ben

---

My ES modded mobo is about FSB 560 1.65V in BIOS, but I don't know retail box how high did it get.

Quote:

---

Originally Posted by AndreYang

My ES modded mobo is about FSB 560 1.65V in BIOS, but I don't know retail box how high did it get.

---

My retail board is hitting 540FSB at 1.65V, 525FSB at 1.45V. I have a modded ES board arriving that is suppose to do up to 600 although it will require a heck of a Northbridge cooler. ;)

A new tool (SetFSB) was introduced to the public.
Thank you. abo.
New SetFSB : for P5B Deluxe
http://www13.plala.or.jp/setfsb/

http://happy.ap.teacup.com/7193/img/1157504120.jpg

CPU：Core 2 Duo E6700 (L623A549)
M/B：ASUS P5B Deluxe WiFi-AP（BIOS：0609）Nomal
MEM：PC-6400 Micron D9GMH 1024MBx2
VGA：Fire GL1000pro PCI
HDD：Western Digital　WD740GD
CPU Cooling：handmade cooling device(Vapor Phase Change Cooling)
Chipset Cooler：Nomal
Power suplly：Zippy-600(Remodeling)
OS：Win XP SP1

CPU/Memory：4：5
DRAM Timing：4-4-4-4-4-25
PCI Clock：33.33Mhz
FSB Termination Voltage：1.45V
ICH Chipset Voltage：1.215V
NBVcore：1.65V
SBVcore：1.70V
Vcore：1.700V
Vdimm：2.40V
Vio：3.35V

Quote:

---

Originally Posted by bugeyes

I haven't done the mod yet but 6x500 is benchable, but 7x500 is not :( even though 3500MHz is fine at lower FSB.

P5B-Deluxe
TT Blue Orb
Gskill64002GBHZ
MCH = 1.45v

http://www.users.on.net/~bugeyes/ind...20copy%202.jpg

---

Well yeah that seems to be the issue- total frequency still matters. Still it is nice to know this mobo can max out a E6300 chip with 7x multi. My DS3 will likely need the 8x multi of the e6400 to reach the true potential of the allendale core.

Quote:

---

Originally Posted by Phosphate

Well yeah that seems to be the issue- total frequency still matters. Still it is nice to know this mobo can max out a E6300 chip with 7x multi. My DS3 will likely need the 8x multi of the e6400 to reach the true potential of the allendale core.

---

nah man even this board is not even close maxing out really good E6300 CPUs....... well at least not my mobo...the chip is priming happily at 1.38v on 3.6GHz.......this chip would most certainly go to 4Ghz but my mobo is not even close to 571MHz FSB :(

My best FSB on an unmodded P5B Deluxe = 520FSB X 7 for 3.64:

http://img206.imageshack.us/img206/6...b520fsbqy5.jpg

http://valid.x86-secret.com/show_oc?id=114761

522 is where instability starts to crop up and 529 will freeze my system in the BIOS. The board will actually do a flat 500 x 7 with just a slight bump to the vcore, 2.25 on the memory and auto on the NB.

Dividers are terrible with the 0507 BIOS. I am pretty much required to stay 1:1.