Printable View
Quote:
Originally Posted by karateo
I tried the above method, but it did not work for me.... at least not for the hard drives that are connected to the ICHR9 ports (I have the jmicron ports disabled). I also tried the registry method (http://forums.pcper.com/showthread.php?t=444831) and that did not work either. Did you do anything else to get hot-swapping working on the ICHR9 ports?Quote:
Originally Posted by Justintoxicated
i have tried both a 8800gt by xfx and a 8800gts 320 by evga and neither workQuote:
Originally Posted by Justintoxicated
edit: also my keyboard and mouse dont light up, there usb.
yeah it disables itself at 1.2 but if I set my vcore setting to 1.35 NO POST, if i leave it to 1.3 and add 102.59% i boot at 1.376, LMAOQuote:
Originally Posted by 64dragon
also anyone help me post at 500? this board does 494 at stock volts but i cant post at 500 no matter what I try and I know the cpu is good for it.
I'm having this kind of issue - with other than first bios, no matter what Vcore I set above 1,25V (in bios), I have no-boot situation... "Funny" thing is, that first official bios works great and I can use full range of Vcore voltage and it's rock stable (sig) :ROTF:Quote:
Originally Posted by Rattle
Take a look at this:Quote:
Originally Posted by Rattle
http://www.anandtech.com/mb/showdoc.aspx?i=3294&p=14
Maybe its defective? I'm sure yu tried clearning the Cmos :( That would be really lame...Quote:
Originally Posted by freaksavior
i tried 2 newest bios and both the same, i figured with an e8600 i might need a newer bios, i will keep going back till i find a good one.Quote:
Originally Posted by Dimek
thanks for the link
Sorry guys another 4870x2 question. What is the first bios that supports the 4870x2 or should I just get the newest bios out? What happens if I try my current bios and it does not work, just a blank screen (no damage or anything right)? I'm guessing that I need to return everything back to stock speeds, now if I have the profile saved will it still be there after the bios update? I like the way it is now, e8500 @ 4.6 (maybe 1.35v don't remember), is that going to be easy to get with the nwer bios? Thank you for any help you can give me.
Well i e-mailed dfi but i need the receipt. i dont have it though, i boght this board second hand.Quote:
Originally Posted by Justintoxicated
im going to try the E7300 in the biostar i have i guess...
try puttin in an old pci card reset cmosQuote:
Originally Posted by freaksavior
its a bios quirk happened to me sometimes with my 8800gt n never happened with 4870
You mean pci video?Quote:
Originally Posted by zsamz_
i do have one OLD ASS pci video card, although i dont know if it works.
:yepp:OLD ASS pci video card:rofl:Quote:
Originally Posted by freaksavior
ha ha, ok. i got a ancient machine with a socket a amd also so i'll try it.
Hey guys. Can help me with my LT X48? I made a thread with my issue here. Thank you all.
What is mean "8.8" error - enybody know?
dieing cpu or dead ram, or power problemsQuote:
Originally Posted by Blackwhite
i get that when i use setfsb n i pushed it too farQuote:
Originally Posted by Blackwhite
just power off the back reset cmos n ...
i need some help. I have 4x1gb of patriot 1066 ram (kept crashing) and ran memtest, it said that it had alot of errors. I put the system all back to stock settings and got 4x1gb of ocz 1066 ram. I put it in (I tired every combnation with the number of sticks and the slots) and it post C1. Put the patriot in, starts just fine, put ocz back in C1. I cleared cmos, C1. The one time it did load and went through the bois, it stopped at the end and said no operating system installed, restarted C1. Put the patriot back in, started right up. I don't know what to do, I've worked on this for a few hours. Any ideas? I'd like to oc again, but anything above 800 and the patriot will crap out. Could the ocz be doa from factory? Appericate any help, thanks.
test each stick individuallyQuote:
Originally Posted by Shalamay
n you need 1.5v on nb for 4 sticks
what ocz kit do u have, and is it single or double sided and what are the voltages, same with the patriotQuote:
Originally Posted by Shalamay
Thank you for the replies. I tried each stick on its own in each slot, no go. I will check the nb voltage, not sure what it is now since I set it at stock (on my oc setting it was 1.55v), but I do have all four sticks of patriot in now. I have these: ozc and patriot. I did set the ram to its correct voltages. I can't even get the ocz to run at 800 (or anything for that matter) and anything over that is a crash for the patriot.
whats memory voltage did you try 2.2-2.3vQuote:
Originally Posted by Shalamay
set timings manually to 5-5-5-15-4-42
if these are d9gkx you can use the settings praz used in dfi forums
thats not what i wanted exactly, i need the voltages on your sticks, the timings on your sticks and if they are single or double sided (are there chips on both sides or just one side)Quote:
Originally Posted by Shalamay
So after CMOS was everything ok yes?Quote:
Originally Posted by zsamz_
yesQuote:
Originally Posted by Blackwhite
i had to turn off power from the back if powersupply for a 1 minute first then if 88 clear cmos
Sorry, the ocz is 2.1v and the patriot is 2.3v with the timings for both at 5-5-5-15. I think they are both double sided. I'm going to try again today, I'll set the nb voltage, ram timings, and ram voltage. I've never had this problem before, just put in the memory and it worked. I don't understand why its this hard? Thank you guys for the help and I'll post back with what I find out.