Guide Thread

Printable View

Show 100 post(s) from this thread on one page

03-06-2008, 02:48 PM
zanzabar

flex whats ur vtt set to, u should need about 1.5, and whats ur NB
03-06-2008, 02:51 PM
GrandMasterJ

Quote:

Originally Posted by GrandMasterJ

In Everest Ultimate 4.2 I'm seeing 56C Core 1 and 46C Core 2 under 30 minutes OCCT load. That Smart Guardian lies and reports 27C. I just reseated my CPU HSF and am using MX-2. HSF is a Xigmatek S963 (cause it would actually fit) mounted with a Thermalright backplate kit and some washers to add additional pressure. Ambient is about 22C.

Where'd I go wrong?

Oh right...that's at stock too on an E8400.

I switched back to my Tuniq Tower, still using MX-2. Still seeing 43C idle for both Cores, but under load Core 1(53C) is 10C higher than Core 2(43C). Uneven chip? What would account for the vast difference? :confused:

That seems Ridicu-High for 45nm. That's about 18 minutes OCCT load side of case closed:

http://farm3.static.flickr.com/2012/...9798b588_b.jpg

I BSOD around 63C-67C.
03-06-2008, 03:19 PM
C-N

Quote:

Originally Posted by GrandMasterJ

Does anyone know a place where the Diagnostic LED error codes are listed?

http://www.bioscentral.com/postcodes/awardbios.htm

Version 6 down the bottom.

CN :)
03-06-2008, 04:39 PM
GrandMasterJ

Quote:

Originally Posted by C-N

http://www.bioscentral.com/postcodes/awardbios.htm

Version 6 down the bottom.

CN :)

Exactly what I was looking for. Thank you.
03-06-2008, 05:22 PM
zsamz_

Quote:

Originally Posted by GrandMasterJ

Exactly what I was looking for. Thank you.

but those idiots need to update that page
03-06-2008, 05:29 PM
deadman'sclick

Quote:

Originally Posted by zanzabar

go to tools cash/mem benchmark

cheers. :up:
03-06-2008, 06:10 PM
GrandMasterJ

Quote:

Originally Posted by kberguy1

Just thought I would mention that my DFI LanParty P35-T2R MB shorted out when I switched to Thermalright Mosfet 9U cooler, even though I used thermal tape and had insulating washers between nut and bolt (had to modify mount/cut off ears for push pins).

Am now waiting for new DFI X38-T2R, but won't use the Thermalright cooler in future. However, I will add an extra fan to cool PWM area.

Mine shorted, but with no lasting damage. The PSU recognized the short and refused to supply power to the board until I fixed the issue, luckily.

The way I have set it up, (there's no room for pictures) is with a sliver of the thermal pad cut off to tilt it forward(towards CPU) off the diodes(?) behind the mosfets. MX-2 is applied to the Mosfets themselves. The Mosfets are actually the coolest component in the case under load, now, with no fan except the case exhaust fan pulling air off of them.
03-06-2008, 06:43 PM
240z

Grandmaster,
Yes would not go past c1 . Tried all remedies posted here no luck. So I grabbed some ddr2 from my dell jewel. Booted right up. Put the Crucial in the dell , hi fans no boot. Tried them again in the x38 no go. All slots one or two sticks. Sad those sticks ran 514 all day long in the 3200icfx at cas 4 :-( @ 2.1v RIP :horse: .Couldn't wait bought the corsair this afternoon. Happy it was ram not the board. :D
240z
03-06-2008, 08:42 PM
t_ski

Quote:

Originally Posted by GrandMasterJ

Were you able to re-mount so it worked properly? I removed it earlier today (ugh) and changed the orientation and added more MX-2 for the grooves. However, it appeared that the heatpipes were making better contact than the aluminum base. I'm less than pleased with this HSF after reading reviews...thinking of jumping on to the water cooling bandwagon.

Yea, the HDT-S1283 is the big brother of the HDT-S963. I went with the S963 for space reasons so I could close the side of my Wavemaster case. I came from a Tuniq Tower with which I couldn't close the side properly.

I noticed this when I unmounted it from my E6850 and was switching to the Noctua. When I got the DFI up and running I tried the Xigmatek again on the Q6600, trying to add some additional paste to account for the contact. When I took it off the Q6600, it looked like only the center pipe had thermal compound on it. :( Unfortunately, I did not have enought room in the case to mount it vertically so the pipes were one over the cores more. I think if I could have, it might have made some difference. All the heat from all four cores were going into one pipe. :(

If you are looking for another 92mm based fan, I had some good luck with the Zaward Vivo, especially with dual fans. It has direct-touch heatpipes and the fins look almost identical to the Xigmatek, but the shroud helps direct the air more I think.
03-07-2008, 05:17 AM
jimmyz

Just to let you all know the x-48 version with ddr2 will be in stock by the 20th. http://www.motherboardpro.com/DFI-LP...ard-p-540.html

I will be getting one as soon as possible. hopefully it will be at my home by my birthday on the 21st.:up:
03-07-2008, 05:20 AM
quake6

I almost bought x38,thank you for telling me this...I thought that there wont be ddr2 version :)
03-07-2008, 05:26 AM
jimmyz

Quote:

Originally Posted by quake6

I almost bought x38,thank you for telling me this...I thought that there wont be ddr2 version :)

Neither did I, Mike called me yesterday and told me about it. (that is customer service!!). not a bad price either. I'm thinking this will be the last good ddr2 board made and since I have lots of DDR2 and no DDR3 yet it is a no brainer. not gonna be hard to sell this x-38 either. so actually the switch won't cost much at all.:up:
03-07-2008, 05:35 AM
Underwater Mike

I finally popped for this board and a whole lot of other stuff, although I skipped the G.Skill and bought OCZ like I usually do. (This despite the fact that, to my surprise, I've received no help on the OCZ forum here.) Once I get everything together, I'll post screenies. Just wanted to say thanks to everyone for the informative comments and advice. :wave:
03-07-2008, 05:38 AM
jimmyz

Quote:

Originally Posted by Underwater Mike

I finally popped for this board and a whole lot of other stuff, although I skipped the G.Skill and bought OCZ like I usually do. (This despite the fact that, to my surprise, I've received no help on the OCZ forum here.) Once I get everything together, I'll post screenies. Just wanted to say thanks to everyone for the informative comments and advice. :wave:

good luck, I think you're going to like it. make sure to start a notebook to track changes. makes a huge difference in tracking gains and losses.
03-07-2008, 06:09 AM
quake6

What is main difference between x38 and x48? Only higher binned?
03-07-2008, 06:42 AM
zsamz_

Quote:

Originally Posted by quake6

What is main difference between x38 and x48? Only higher binned?

thats whats been said but if it is better i be gettin one too lol
03-07-2008, 06:50 AM
quake6

I only want 515-520 FSB for super pi with quad only that :p:
03-07-2008, 07:55 AM
Jor3lBR

Quote:

Originally Posted by zsamz_

thats whats been said but if it is better i be gettin one too lol

Just flash the X38 with the X48 bios! ;D

-make sure you have spare bios chip.
03-07-2008, 10:30 AM
flexy

Quote:

Originally Posted by Jor3lBR

Just flash the X38 with the X48 bios! ;D

-make sure you have spare bios chip.

isnt X48 a total diff chipset??? :) If someone flashes to this (or to the DK bios for that matter)..let us know...

Btw. i have a ANNYOING issue that my bios settings are often not kept. I have a OCCT stable setting now and sometimes resetting PC just reverts back to stock....or it just hangs. So i have to turn off (power button on back) the PC to be able to use the settings. Not always, but sometimes.

>>>
zanzabar:
flex whats ur vtt set to, u should need about 1.5, and whats ur NB
>>>

1.5VTT ??? I can try, its at 1.4 right now, NB is is 1.502 (Bios says 1.52).

btw. 1.5 VTT safe on air????

edit: zanzabar:

i increased VTT to 1.48 so it read 1.50 in bios, i also changed GTL Ref 69% and 68% accordingly to the new VTT voltage.

It lasted exactly ONE second in OCCT til i got a BSOD. Mind you, 60mhz less and i am OCCT stable. This CPU is EVIL.
03-07-2008, 10:43 AM
Jor3lBR

No you can't flash I was J/K.

Quote:

Originally Posted by flexy

isnt X48 a total diff chipset??? :) If someone flashes to this (or to the DK bios for that matter)..let us know...

Btw. i have a ANNYOING issue that my bios settings are often not kept. I have a OCCT stable setting now and sometimes resetting PC just reverts back to stock....or it just hangs. So i have to turn off (power button on back) the PC to be able to use the settings. Not always, but sometimes.

>>>
zanzabar:
flex whats ur vtt set to, u should need about 1.5, and whats ur NB
>>>

1.5VTT ??? I can try, its at 1.4 right now, NB is is 1.502 (Bios says 1.52).

btw. 1.5 VTT safe on air????

It is annoying and it's a motherboard or bios problem. Try raisin NB to see if it will help.

But I have my mobo stable to and every now and then - Bios Checksun Failure, almost like the board Cleared Cmos by itself...

This is a handful mobo.
03-07-2008, 10:51 AM
Praz

Quote:

Originally Posted by flexy

Btw. i have a ANNYOING issue that my bios settings are often not kept. I have a OCCT stable setting now and sometimes resetting PC just reverts back to stock....or it just hangs. So i have to turn off (power button on back) the PC to be able to use the settings. Not always, but sometimes.

Benchmark/gaming stable or not this issue is most always stability related. Causes in order of likelihood.

Northbridge voltage
Phase Delay change
Memory voltage
Memory timings
03-07-2008, 11:11 AM
flexy

praz, hm.

NB 1.5, SB 1.5, DRAM 2.22. i was testing with this setting using OCCT 40+ mins stable as well as memtest in Vista (2 threads) no errors w/ 100% coverage.
03-07-2008, 11:51 AM
Jor3lBR

Quote:

Originally Posted by Praz

Benchmark/gaming stable or not this issue is most always stability related. Causes in order of likelihood.

Northbridge voltage
Phase Delay change
Memory voltage
Memory timings

Praz this happens with stock settings also...

Looks like you have the only X38-tr2 that's perfect in here. What's your Rev. number?
03-07-2008, 11:56 AM
GrandMasterJ

Quote:

Originally Posted by flexy

Btw. i have a ANNYOING issue that my bios settings are often not kept. I have a OCCT stable setting now and sometimes resetting PC just reverts back to stock....or it just hangs. So i have to turn off (power button on back) the PC to be able to use the settings. Not always, but sometimes.

Same issue, kinda. Sometimes I just don't boot at stable settings. Power off the PSU, wait 10 seconds, power back on, and like magic I boot up.

Also, if someone could advise...

I can't get lower than Performance Level 7. Even with 1.6v on the Northbridge at 400FSB, it won't do it. I can get Performance Level 6 at 333FSB with 1.55v on the northbridge... Am I missing some setting that would make this possible? I see a lot of bench screenshots with 6. I haven't touched the GTL settings.
03-07-2008, 12:43 PM
Praz

Quote:

Originally Posted by Jor3lBR

Praz this happens with stock settings also...

Looks like you have the only X38-tr2 that's perfect in here. What's your Rev. number?

Sorry you feel that way. As far as I know there is no perfect board. However using settings that the board prefers rather then what I would like goes a long way toward solving most issues. I can duplicate these same issues with a slight change in any of the settings I posted. But it's no problem for me to not post in this thread. Good luck with your board.

Show 100 post(s) from this thread on one page