new bios for x1800xt

Any program wich would rec temps so I could check them later?

Quote:

---

Originally Posted by RistoEe

Any program wich would rec temps so I could check them later?

---

the ati tool temp monitor is "recording" your core and envoirment temps, and shows you lowest-highest and avarage :)

Quite some difference between cards and temps on stock HSF it seems. Mine idles at about 45 degrees (stock volts/bios, amb 20 degrees, 40% fanspeed). Highest temp atitool reports while gaming for hours or looping 3D is 65 degrees. Fan is set to run @ 60% above 60 degrees. It wil do 700/800 on stock volts and bios without a problem. I did not remount the hsf but this might be a good idea for the "hot" cards.

Hmmm...this is very interesting with the Memory clocks...might have to try this out and see what I can get out of it.

Quote:

---

Originally Posted by cantankerous

hmmm weird, never heard of this till now and I thought I was actively following all these threads. Strange how ATI would set the voltage higher than needed. The only thing I can think of is the core intelligently adjusts for voltage under load but perhaps the ram doesn't so they gave it a little extra bit just to be sure it would be stable under load or an average overclock.

Give this a try eva and let us know how it goes. If that is the case I will lower mine as I don't plan on going over 792 anyways until I get better cooling/lower temps. I hope a slight drop in voltage will lower pcb/ambient temps some on the card.

BTW, I emailed Arctic Cooling last night about an aftermarket cooler for the X1800XT and they said they have one in design now and should be out in the next 2 months. It does cool better than stock apparently. I hope so! Cooler temps and quieter fan is #1 on my list. I would buy this new cooler asap. If I could even keep temps at 75c full load with much quieter fan I would be happy.

---

well today i installed my 1HP portable air con unit in my room so might change my max cpu and video card clocks and temps so what hehe

According to FedEx I will have my Opteron 148 tomorrow. Time to have some fun for me.

Quote:

---

Originally Posted by ugp

According to FedEx I will have my Opteron 148 tomorrow. Time to have some fun for me.

---

hahaha good luck:toast:

Quote:

---

Originally Posted by thelostrican

hahaha good luck:toast:

---

Thank you, Thank you.

Quote:

---

Originally Posted by FUGGER

ALWAYS downclock your X1800 video card before you flash to at least 500/500 to prevent corruption and failed bios flash.

---

YES!

Finally worked for me after doing this.

Thanks FUGGER!!

BL

According to this hole thread, which card should i buy now to get some "positive" :D results ?

new bios
cpu fx55 san diego 3020mhz ram vitesta 600 timing 2.5/3/3/6 232x13
scheda sapphire x1800xt
freq 762/918
watercooling cpu/vga

http://img395.imageshack.us/img395/6591/100441tf.jpg

Those are amazing clocks maxxpt, but system mem bandiwth is holding you back there. SHould be getting at least 11500 with those clocks. Is that with a divider or 1:1 on your fx?

Perkam

Ok... now I've checked temps while playing and it was 80... put the coller max and temps were 57 :)

Does anyone use RivaTuner?
If so what are your volt readings with stock and XTPE bios?
Im at 1,3V in 2D and 1,4 with stock and 1,48 XTPE in 3D mode.
And what would be the max safe voltage?

Quote:

---

Originally Posted by RistoEe

There's been "a few" problems with these mobos around the world :D This is my second one, 1st one wasn't even stable on stock clocks.

Maybe I have to start looking for other mobos... kind of liked DFIs until I got my hands on these RDX200.

---

hmmm not good, dont lose hope fella, they not all bad...
This RDX is pretty smooth paired with GeCubeXT not flashed...yet :slap:

http://img488.imageshack.us/img488/2...ckxt0xa.th.jpg

I decided to be stupid tonight and flash my XL with an XT bios. I did not use the PE bios floating in this thread. Here were the not so good results.

Upon reboot the screen went black - nothing. I ended up turning the system completely off and rebooting. That worked - system booted into windows and it began displaying that it found new hardware. It did not find acceptable drivers and prompted me for them. I selected to let it find them - it did not. I then re-installed the 5.12 drivers - no luck. Loading ATItool confirmed the bios was different - clocks were now at 600/700 except ATItool did not recognize the card. So, I could not check the voltages. Windows was still using the base VGA driver so things were a little clunky. I did not do any benching because of this.

Under the control panel/system/hardware it showed unkown ? hardware.

I reloaded the bios flashing tool - it said I had an ATI 520 installed. I forced a reflash to my saved XL bios. That worked and a reboot put me back to normal. A little risky - but worth the try.

At least I am back to normal. Not sure what I was thinking. I would have tried to XT PE bios in this thread, but I know the card can't touch 800 mem with those stock volts.

Thanks for trying. Took a lot of balls to do what you did. I know I would have freaked out getting a black screen after a flash. I am glad you got it all working again though.

So you flashed a 256DDR XL card to a 512DDR XTOC Version? That is nuts!! LoL

X1800XT 700/1600 oc 750/1750

3DMark 2005 - 10182

Quote:

---

Originally Posted by aleko28

X1800XT 700/1600 oc 750/1750

3DMark 2005 - 10182

---

bit of a low score for the high overclock. i got 10284 729/1620 with standard bios..

Quote:

---

Originally Posted by aleko28

X1800XT 700/1600 oc 750/1750

3DMark 2005 - 10182

---

PSU probs??? :confused:

I´ve got 10486 at 750/810 with BBA X1800XT standard bios...
CPU fx55 san diego 2900MHz
GEIL ONE S
watercooling cpu/vga

<a href="http://imageshack.us"><img src="http://img203.imageshack.us/img203/8462/2k5cpu2900mhzvga7501620mhz1xr.jpg" border="0" width="1024" alt="Image Hosted by ImageShack.us" /></a>

Quote:

---

Originally Posted by cantankerous

Thanks for trying. Took a lot of balls to do what you did. I know I would have freaked out getting a black screen after a flash. I am glad you got it all working again though.

---

Not sure what I was thinking (maybe my thought was I could explain it to my wife that my card simply died and that I needed to buy a new XT to replace it). I went in there to simply back up my current bios. I could not resist trying. Funny thing is I held my mouse over the proceed button for a minute - finally said what the hell. Black screen made me sick. Not sure why it did not work. I have a Sapphire card - but it merely has the sticker slapped on it.

One other interesting point. There is mention that you have to set your card to 500/500 before flashing - after flashing to the XT bios, I tried that. Teh screen went bright orange and the system froze. Not a good feeling. Luckily it booted and I left the clocks at 600/700 and the reflash worked.

Quote:

---

Originally Posted by Quigs

Not sure what I was thinking (maybe my thought was I could explain it to my wife that my card simply died and that I needed to buy a new XT to replace it). I went in there to simply back up my current bios. I could not resist trying. Funny thing is I held my mouse over the proceed button for a minute - finally said what the hell. Black screen made me sick. Not sure why it did not work. I have a Sapphire card - but it merely has the sticker slapped on it.

One other interesting point. There is mention that you have to set your card to 500/500 before flashing - after flashing to the XT bios, I tried that. Teh screen went bright orange and the system froze. Not a good feeling. Luckily it booted and I left the clocks at 600/700 and the reflash worked.

---

did you use atitool or overclock, to underclock. as overclock won't work for everyone.

Flashed sapphire to PE, done 3dmark05 at 9451 at 760/800 my CPU is holding me back though.
2400mhz sigh.

Seems stable though but me on watercooling mcw50 and temp now is 41c, and goes to around 52 or so when benching.