My solid container is finally here...cool cnc mpeg

Printable View

Show 100 post(s) from this thread on one page

12-30-2005, 06:18 PM
k|ngp|n

Sooooo close tonight.....
Still only around -30c to -40c on the cards. 175 points from 05' WR with only 3860mhz lol:
http://pic8.picturetrail.com/VOL256/.../123601748.jpg

50 points from 03' WR. 44k soon :)
Run was at 740/2144. 800+ on the cores should give around 44.5k
http://pic8.picturetrail.com/VOL256/.../123601745.jpg
12-31-2005, 01:37 AM
Dumo

Almost there KP:toast:
12-31-2005, 04:55 AM
k|ngp|n

Quote:

Originally Posted by LucusScott

KP>
Set PCIX Freq at 118mhz in the bios ;)
This will give you 50points in 2k5 and 90-100 in 2k3 right off the bat guart. :D

Thanx for the tip...."Lucus" ;) Effect on clockability?
12-31-2005, 07:33 AM
k|ngp|n

Quote:

Originally Posted by LucusScott

No effect at all on overclocking. Its just above 118mhz your scores start to go down not up as you saturate the bus. :)

test it on air run 2 2k5's with it at 100mhz and 2 at 118mhz to rule out a lucky run. :)

Thx again. I'll try it in a bit. 123-125pci-x freq was cool on the intel board with 512mb gtx, wasn't sure about the DFI.
12-31-2005, 12:56 PM
Cpt Twitchy

You don't even lok like your pushing the cards in 03 :toast: Keep up the nice work.
12-31-2005, 02:49 PM
k|ngp|n

Got shamino :D
http://pic8.picturetrail.com/VOL256/.../123716972.jpg
Next up Kinc and Overklokk. Only 60 points more and I got it. Had some minor problems with the cards last session, but I think I got it sorted now. Cards are now bench stable through 05' at 2171+ on the mem. GPU temps were about -45c to -50c or so today. Mother nature is giving me fits again, otherwise I think I would be sitting here at 44k right now. 118 pci-e did help a littlebit, but not great in 05'. I got about 70 points xtra in 03' and maybe 10 in 05' I can take 05' WR with around 3870 on the chip I think. I am bailing on partying later to try for these two WR's tonight. I just cant stop.
12-31-2005, 05:30 PM
gocchin

You're the man Vince.... It's going to be a smashing new year for you! All the best!!
12-31-2005, 06:00 PM
Jort

That all wishes may come true!!!;)
12-31-2005, 08:01 PM
G H Z

Quote:

Originally Posted by k|ngp|n

I am bailing on partying later to try for these two WR's tonight. I just cant stop.

WTF :confused: ;)

Good luck KP :)
01-01-2006, 04:05 AM
k|ngp|n

Happy new year guys! :toast:

Quote:

Originally Posted by G H Z

WTF :confused: ;)

Good luck KP :)

Well G...I couldnt seem to convince my girlfriend that orb domination was worthy of cancelling our dinner and pary plans..lol.
Will be benching later today ;)
01-01-2006, 03:09 PM
k|ngp|n

A little CPU testing with def single card. Getting real close to 3900mhz with 15x for 3d stable. I think this will be good enough for now :O
-92c held for whole run:
http://pic8.picturetrail.com/VOL256/.../123878288.jpg
01-01-2006, 03:18 PM
k|ngp|n

Good call. I should grab some up tommorrow....why not. Last tccd I used was gskill long time ago. WHats my best bet for getting some good ones?
01-01-2006, 03:27 PM
Overklokk

Dam nice Kingpin :)

Looks like Kinc and i must start upp the rigg again soon :) My FX57 did 01 with singel GTX today @ 3906mhz with -105c load temp on evap . But my w2k instal was bad so only godt about 48473p :(

http://service.futuremark.com/compare?2k1=8847154

Wil reinstall OS and get som better cooling on the GTX in a few days. Think my fx can do about 3930mhz under my 3 stager 3d stable :)
01-01-2006, 03:28 PM
gocchin

Nice work V, I see you're almost there in 05 on the HoF.... :)
01-01-2006, 03:33 PM
k|ngp|n

Quote:

Originally Posted by Overklokk

Dam nice Kingpin :)

Looks like Kinc and i must start upp the rigg again soon :) My FX57 did 01 with singel GTX today @ 3906mhz with -105c load temp on evap . But my w2k instal was bad so only godt about 48473p :(

http://service.futuremark.com/compare?2k1=8847154

Wil reinstall OS and get som better cooling on the GTX in a few days. Think my fx can do about 3930mhz under my 3 stager 3d stable :)

3930 would be very nice. I prolly won't run 01 with the SLI setup.
Sounds like a battle is coming.... GL with your hardware. You guys are tops on your own...as a team just awsome :) :toast:
01-01-2006, 03:41 PM
k|ngp|n

He got me on gt2 by a little too.
2gb scores how much better than 1gb clock for clock?
2gb good clockers on average?
01-01-2006, 04:07 PM
k|ngp|n

Quote:

Originally Posted by LucusScott

If you order one of the UCCC kits you should be good for 285-295mhz at low 2.6-2.8v.

Lard. at vr-zone did a UCCC 1024x2 Corsair pc4000 review and he got almsot 300mhz at 3-4-4-8-1t as for how much you gain from 2048 over 1024 at low multi high htt thats unknow as Denny was the only one going that route. :(

Also Im sure a 3400-3500mhz dualcore would push you up a few points. :)

Sucks when your off by under 100 points in a tens of thousands benchmark.

2x512 for now sounds good, thanx for the link. Dual core will be next thing for sure. The numbers look great. If these cards survive the next week, I will run them with a dc chip eventually :) I have some pretty tight solid gpu containers that should be done in the next day or two. I was going to wait till they were finished to bench these cards really hard, thats why the low core clocks. I only needed enough gpu power for the top spots, think I am good now. THis goofy container I made for the middle card has 0 capacity ;) and I dont want to take the volts up to higher than 1.8 on it.
01-01-2006, 04:31 PM
s7e9h3n

Quote:

Originally Posted by LucusScott

Nice CPu power. A 13x300 with TCCD combo would give you 100-200points over the 15x 250-260mhz bh-5 combo in 2k5. It would also but less stressful on the CPU becasue of ram voltage/timings so the lower multi should be able to work then.

Denny ran 3800mhz 13x29xmhz and his system power with 2048meg of 3-4-4-8 uccc ram was like 2-3fps faster in gt1 over kinc at 3900mhz+.

Not sure if you have any tccd/uccc sammy there, but something to add to your list of things to try if it comes down to it.

A couple of issues with this though....
1. Can the cpu run 300FSB @ those temps? I have a funny feeling that the cpu's gonna freak out at that speed @ those temps.... :p:

2. If k|ngp|n's using an expert board, there may be some issues running TCCD.

3. That G.Skill TCCD is G.Skill LA's - IIRC, those run @ guaranteed rated timings @ 2t. 1t if you're lucky ;)
01-01-2006, 04:53 PM
s7e9h3n

Quote:

Originally Posted by LucusScott

A couple of issues with this though....
1. Can the cpu run 300FSB @ those temps? I have a funny feeling that the cpu's gonna freak out at that speed @ those temps....
A:I say no in the sense that less VDD ram voltage which ties into the on chip ddr controller on the chip thus less stress than 2-2-2-5@3.6v.

2. If k|ngp|n's using an expert board, there may be some issues running TCCD.
A:Again this isn't 100% true. Some Experts have issues, but only with select CPU's which are mostly dualcore chips and select Multi's.

3. That G.Skill TCCD is G.Skill LA's - IIRC, those run @ guaranteed rated timings @ 2t. 1t if you're lucky
Almost all the FX pc3200 can hit 285-295mhz at 2.5-3-3-5-1t 5 users here on XS alone got this high .
Sorry I posted the wrong newegg link before you want this stuff.
http://www.newegg.com/Product/Produc...82E16820231035

1. So you're saying that less VDD = higher FSB achievable in the cold?

2. I have issues with my expert @ 300+ FSB, TCCD, and my 57 :( (Then again I didn't try the x13 mult:p: )

3. OK, that's better...Didn't think that LA's were the new "have-to-get" TCCD's ;)
01-01-2006, 04:56 PM
Cpt Twitchy

The best TCCD out there atm is G.Skill FF and The best 2gig kit is Crucial ballistix pc4000. Then again for the best TCCD ever I'm sure there are some individuals around here who have access to the best around ;) i think you know who I'm talking about hehe.

Tim
01-01-2006, 05:05 PM
s7e9h3n

Quote:

Originally Posted by LucusScott

A couple of issues with this though....
1. Can the cpu run 300FSB @ those temps? I have a funny feeling that the cpu's gonna freak out at that speed @ those temps....
A:I say no in the sense that less VDD ram voltage which ties into the on chip ddr controller on the chip thus less stress than 2-2-2-5@3.6v.[/B]

Wait a sec, just re-read and did you mean to say VTT not VDD?
01-01-2006, 05:22 PM
s7e9h3n

Quote:

Originally Posted by LucusScott

The voltage on the ram that tracks with the on die controller exactly.

Might be VTT I thought It was a VDD voltage. :confused:

VDD = Vdimm, VTT = what you're talking about :p: - 1/2 of VDD....
01-01-2006, 07:03 PM
[XC] moddolicous

The best TCCD I've seen were the new Geil One S. SPI32mb stable @ ddr 644 2.5-3-3-7. Seems pretty good to me.
01-01-2006, 08:27 PM
Cpt Twitchy

Quote:

Originally Posted by moddolicous

The best TCCD I've seen were the new Geil One S. SPI32mb stable @ ddr 644 2.5-3-3-7. Seems pretty good to me.

Was that OPB? If so I don't think it was Geil:cool:
01-01-2006, 08:32 PM
vapb400

Quote:

Originally Posted by Cpt Twitchy

Was that OPB? If so I don't think it was Geil:cool:

I think it was AndreYang, I think he beat out OPB a couple days after OPB grabbed the record.

Show 100 post(s) from this thread on one page