Printable View
What is you HT x multi, Dani? 260x10 or 290x9 @ 1.45v?Quote:
My CAA2C 0506BPMW can do 24h StressPrime @ 2605MHz 1.45V
I get 45C idle and 55C load @ 1.275 x 126% (1.552v CPUz) is it normal
or should I reinstall my AMD HSF. I'm using AS5 and Tambient is at 21C.
Thanks
try 10x260 with lower voltages, sometimes you'll be surprised that the lower voltage works better cause of less heat... some people are hitting 2.6 with 1.5v. Your temps sound reasonable...
I will do it right away bud. ;)
Yep Kawaii, SuperPi 2M and 3Dmark03 1 pass stable @ 260 x 10 1.45v (stock voltage) 2.5-3-3-7 2.8v 1T:woot:
Ambient 21C idle 42C load 52C can't wait for my water setup to be completed and test higher Vcore! :banana:
I needed 1.648v with my 3500+ winnie CBBID to get stable at 2.6 Ghz :slapass:
My CAA2C 0509 FPMW looks to be a good one.
good to hear kos, now slowly increase the HTT 3mhz at a time keeping the volts steady... I wouldn't be surprised if you could hit 2.7 at stock volts...Quote:
Originally Posted by Kosmic71
Low HTT for testing 24h StressPrime, ambient temp around 24ºC and boxed cooler=:slapass: with tempsQuote:
Originally Posted by Kosmic71
With DryIce 3363MHz SuperPi8M :toast:
http://koti.mbnet.fi/dani69/DFI%20nF....45V%2024H.gif
http://koti.mbnet.fi/dani69/DFI%20nF...0Validator.gif
Nice OC Dani :toast: I saw your pics, Finland looks just like Quebec province Beautiful !!! Outdoor OCing must be fun lol!
Update: 260 x 10 @ 1.45v 2.5-3-3-7 2.8v SuperPi 32M completed. :toast:
My CPU just crap Prime95 after 2 min tho :confused: I'm no fan of Prime. :slapass:
Magnum PCQuote:
Originally Posted by Enigma422
We've been selling them, but I haven't had a chance to bench any yet.
I broke 300 FSB for the first time woooWOOOOO! :toast:
300 x 9 @ 1.536v 2.5-3-3-7 tRC 7 @ 2.9v
I tested SuperPi 1M & 2M and Sisoft so far. I'm at 55C under load with
stock AMD HSF, getting hot.
Quote:
Originally Posted by Kosmic71
Coming along nicely, Kosmic71. :)
I have no clue what my temps are, but am running a DC
program ( D2OL, 100% load ) at 255 x 11 @2-2-2-11.
Got the CAAXC chip installed.....it's not a clawhammer core.....it's a Newcastle. Newegg must have fouled up & shipped the wrong boxed processor. CPU-Z plainly ID's it as Newcastle. I was abit suspicious when everyone ordering these chips got the CAA2C. Now I know. I will RMA it back to Newegg monday.
are u using the latest version of cpuz?Quote:
Originally Posted by joe111
Thanks SOnic I was using 1.27...identified Newcastle. Downloaded 1.28....now it's Clawhammer. I'll do some testing. By the way what bios you using?
I'm using the official 310 bios, I tried pretty much every single one out there and decided to stick with this one for now..
I just got my xp-90 and used ac5 on it. I played doom 3 for 2 hours at 2651 mhz with occational lags my idle temps so far are 38c and load is 52 with sp2004 (it seems to create the most heat). I was only able to play doom 3 at ~2600mhz max b4 a crash. None today! Had my PNY 6800gt maxed out to 1150/442 with a Zalman 700 cooler and ac5. For those of you I see speaking japanese: 3500 caa2c ga daisuki!
Just finnished a 3dmark 2001se run with my CAA2C @ 3224Mhzs and X850XT PE stock cooled :D
http://service.futuremark.com/compare?2k1=8545388
scwam and silence, could you please tell us the voltage you needed and Silence, what did ur load temps look like? Great clock btw :)
1.85v to bench @ 3224Mhzs. Load temp arround 6ºc (very very hot cpu :S)Quote:
Originally Posted by kryptobs2000
@ 3100Mhzs 1.69v load temp is -2ºc
Nice CPU you got there, mine is max out at 3140MHz @1.85v (3dmark benchable) with Vapochill LS.Quote:
Originally Posted by [_Silence_]
Temps are -35C evap under load and temps 10C.
My voltage I believe was left at 1.5, may have, but doubt i increased it on that game, if so it would have been 1.525. My system seems to require upping the volts starting at 2685. At 2760 windows ussually does not boot with higher volts, really depend how cold it is. I can not run anything stable other than winodws at around 2700 so far. ~2730 windows tends to shut down in the middle of pulling up apps.
The rest of you guys got some crazy ass equipment out there with those chillers! Cool stuff.
I don't want to test stability with sp2004 or prime yet since I don't trust this temp sensor always changing when I put new paste on. I had to reapply ac5 correctly and the temp is way off again. Once it gets acurrate Ill find out if stress tests can last more than 15 minutes past 2610 or so.
Just tried my best one under single stage phase. (-43c evap load)
CAA2C 0506BPMW 00569
Never mind the super-pi score. Im using a crappy Neo2 which wont let me run RAM over 215-220 with divider.
Super-pi stable @ 3200Mhz - 1.86vcore
I have a question for you guys with these Chips, preferably with Z's. Would I be better off going to a mid range water setup or just getting an XP-90C with some AS5, I thought I read that water wasnt doing much for you guys but I'm looking at about 80$ for a Air setup and a water setup would cost about 300$.
Basicaly i'm wondering how wel lthese respond to water compared to a nice Air setup.
BTW. right now i'm ram limited to about 227 x 11. Not too bad on box cooler?
Interesting thread I started....damn...loook at the size 33 pages!
I'll shutup now .. :)
I'm up to 300 x 9 @ 1.536v 2.5-3-3-7 tRC 7 2.9v 1:1 1T with stock AMD cooling.
ambient: 22C
Idle: 45C
load: 55C-57C
I'm going water this week. I will let u know Magnj. I'm sure that my home
made water cooling setup will be way better than any air cooling.
Swiftech 6002-64, MCP650, Black Ice Xtreme-2 (120 x 2) radiator, 1/2" ID
PromoFlex tubings.
Edit: ambient temp should of been around 18C-19C that day. 22C is the
house temp not the computer room temp, duh!! :p:
Nice thread indeed, informative.
If you get air then go to svc.com
I got their non copper version for $29. If you do water you might want to consider that winter time your whole house might be cooler and this would keep your water volume colder thus keeping temps colder for a longer time.
those temps are way too good for stock heat sink with a clawhammer, my XP-120 gives me higher temps than those at that voltage and speed, but I can't get it prime stable at that speed, can you?Quote:
Originally Posted by Kosmic71
No S0nic I'm not Prime stable, and about the temps I was telling the truth,
mostly lol!. When I'm trying to OC my system to the limit I remove the
computer side panel, I open the computer room window and use a house fan
to blow fresh air into the room. That day the exterior temp was low around
8C to 10C. The Tambient of 22C is not exact, it was the temp in the house
not in the computer room, it must of been around 18C-19C.
I used the same settings today, just for you :rolleyes: and the exterior temp
is warmer today, around 16C. My system is nowhere near stable, it just that I
was excited to hit 300FSB for the first time.
300 x 9 @ 1.400 x 113% (1.536v CPU-Z) 2.5-3-3-7 tRC 7 @ 2.9v 1:1 1T
Tambient: 21C
Tidle: 45C
Tload: 57-60C
Memtest86: stable 4 passes no errors
SuperPi 1M: 31.422 sec
SuperPi 2M: 1m 12.266 sec
SuperPi 4M: fails
SiSoft Sandra Memory bandwidth Int Buff': 7868
SiSoft Sandra Memory bandwidth Float Buff': 7780
SiSoft Sandra CPU arithmetic Dhrystone ALU: 12381
SiSoft Sandra CPU arithmetic Whetstone FPU: 4257/5505
3Dmark03: fails
3Dmark05: fails
Prime95: fails
I hope that can help.
Sorry wasn't implying that you're lying, thought maybe ur sensors were messed or something, right now this is what I'm running..Quote:
Originally Posted by Kosmic71
http://www.xtremesystems.org/forums/...id=29347&stc=1 http://www.xtremesystems.org/forums/...id=29348&stc=1
http://www.xtremesystems.org/forums/...id=29350&stc=1
my idle is 41C and load is 54C, this is inside a closed case in a warm room, I was expecting lower temps with that vcore though, maybe I need to reseat my heatsink and reapply some AS5..
but I guess 2700 isn't reachable with this processor, for some reason I was so sure that I'll reach it with ease :(
I hope I won't have trouble selling it in order to get a venice/san diego..
My temps don't really seem to increase when overclocking 20%. Their is a slight increase of around 5c overclocking at peak cpu output. Now I believe that my cpu temps are being reported to low. Shows ~34c, 2 degrees lower than my system temps. Where the hell are these probes located anyway! I tell you what, you can touch the leading edge of the xp-90 base and it doesn't even feel lukewarm??!! Feels like touching your table at room temp. Odd. Put on ac5 4 days ago. Was showing 54c idle then. 2 days ago the temp probe bounces down a few degrees lower than the stock hsf to the now 34c. I wish there was a cheap ribbon temp sensor i could stick between the cpu and heatsink safely.
Oke, I can pick a Amd 3500+ Clawhammer with one of these codes CAA2C 0504GPMW, CAA2C 0506BPMW, CAA2C 0505DPMW.
Which one should i take?
my CAA2C 0504GPMW does 2.8ghz at 1.65voltsQuote:
Originally Posted by Glitch
Got one of those: 0504GPMW, well all i can say is 3224Mhzs through 3DMark 2001SE with r404a Mach I, 3224Mhzs for SuperPi 1M, 3450Mhzs screenshot, well not a bad cpu :PQuote:
Originally Posted by Glitch
ya, the 0504 GPMW is probably ur best bet..
got 3 of these at a local retailer, the 1st ive tried to oc is doing extremly well
250X11@2750 1.6v Stock HS w.tornado attached, 55-56C at 100%load after about 12 hours. atm my ram is the problem, doesnt go past 250 very well at all. Hopefully ill be picking something a little better up pretty quicky =)
Going to test my mate's config that he just ordered.
Amd 3500+ Caa2c (boxed)
MSI K8N SLI
2*512MB Gskill 4400
MSI x850xt
7700Cu didn't arrive at time so I have to do it with boxcooling.
Will be testing saterday and I hope the config does 260*10 at stock voltage or 1.55V. Then we are satisfied for running this config 24/7.
If I got more time I'll try to see how far this proc goes.
:slap:
I don't want to see that!!!Quote:
Going to test my mate
Maybe its a girl :p :banana:Quote:
Originally Posted by Kosmic71
I just got my Hammer from ZZF and its a CAA2C 0509CPMW. Still waiting for my PCP&C PSU, will post results soon as I get my PSU. Hopefully this will give me a good enough OC that I won't regret having not waited for Venice.
isn't it too late to buy clawhammer now? some stores already have venice in stock..
I ordered my Hammer last Friday. I couldn't wait anymore and wanted to get my system built. I had it sitting for a months waiting to get everything together and I saw that Monarch kept pushing the date back on the 3500+ Venice so I decided to get the Hammer instead.
lets hope u got a good one, mine wouldn't do 2.7 stable on air so I'm already thinking of replacing it with a venice/san diego..
2.7 (300 x 9) is all I'm asking for
I probably would have waited for Venice if I had known that the Egg was going to start selling them the day I get my chip and that my PSU is on backorder so I had to wait anyway :(. Oh well, I'll probably end up going with a Diego this summer, for the extra cache at the minimum, and play around with my Hammer for now. It's going to be WCed so hopefully I get better results.
alright get this one. I have a Caa2C 0506FPMW. I am running 255x11 at 1.66v With my SLI-DR and good watercooling I am at 40°c idle and hit's over 65°c load! I have seated and re seated my waterblock about 7 times and the temps don't change. Now I went from my winny at 245x11 at 1.66v doing 28°c idle and 38°c load. My temps can't go up that much from winny to CH? When I had my 3200+ S754 CH it wasn't that hot.
So an ideas except getting phase change?
try lowering volts, you may still be stable on lower volts.
I tried lowering down to stock and it was only a diff of 1-2°c. Just to experiment I stuck my winny back in and I dropped 10°c at idle and 20-25°c at load. This CH is fricken hot, but does real pretty well. It's just the temps that seem to be holding me back. Once it get's over 60°c is where I start to get unstable. Looks like I may have to put away my 2.8ghz 24/7 goal again. I need to be able to game. Guess this may be going to the FS section and find a home with someone with phase change.
with some tweaking i got mine running 2.85ghz air now =)
i can do 2.9 but not very stable :( although i have a feeling my ram is the problem the cpu is @ 56C full load
mmmh! yeah your Claw is getting dang hot. I will go water next week, I hopeQuote:
I am running 255x11 at 1.66v With my SLI-DR and good watercooling I am at 40°c idle and hit's over 65°c load!
that my temp won't limit my OC. What water cooling system are you using?
yup, these are the hottest running A64's, even with low volts u'll still get crazy high temps, look at my post above (if you haven't already)
yeah they are very hot. I just wish I could get 2.8ghz stable then I wouldn't care about temps.
Kosmic I have a swiftec 6002 WB, AquaXtreme 50z pump, BIX radiator, Delta 85cfm 30db 120mm fan.
I am going to try and load this claw up again and have a go at it. High temps within reason aren't a big deal if you are stable, and my winny is only stable at 1.65 while the CH is stable at almost 2.8ghz I still might just sell it though as I'll prolly get more for the CH than the winny, then I'll just pick up a venice.
Well, I have a CAA2C APMW... I have it under water (cool by corsair), at 2700@1.6v, I'm getting around 47-48c under load, 24 hours prime stable. 1msuperpi@31s 5m46s@8m superpi, I'll try to get some pics up, as I've only seen one other person reference the APMW. Can't wait for the San Diego I ordered!!!!
Glitch:
Mine is caa2c 0508APMW FYI. It will do a 2650 overclock running games fine.
Likwidkewl: There is no way your temps are accurate with that watercooled system. Your sensor is wrong like mine was. Let your system cool down overnight. Turn it on, immediately go into bios and check your system and power mgmt test against your cpu temps. Your cpu temps should only be a few degrees higher than the other 2. If All three read anything above 27c immediate then you know the probe is messed up. This way you can rule that out. If your cpu temps is more than 5c higher than the other 2 then: your reading is still not accurate. I get a 2-3c higher reading on the cpu at first boot:
system 23c
power 23c
cpu 26 c
after 5 minutes cpu is @ 31c
you can even downclock to 1000mhz to give it the benefit of the doubt. Try reflashing your bios with an older version and see if that corrects it. If not relash back to the new bios and check again. I found out my initial reading of 80c throttle with a warm stock cpu was at least some 20c higher than actual.
Av8 + 3500 (xp-90)
PNY 6800 GT (Zalman Cu700)
(2)Maxtor Diamond Sata (Raid0)
played with my caa2c some more. 1.52vcore and stock HSF, it does 2640mhz all day long. Found out my gig of BH-5 doesnt like to run above 245fsb yet :stick: so i threw in a divider, and the cpu will run up to 2755mhz. Have a Xp-120/panaflo on the way to test more :banana:
just did a quick test on my friends caa2c 0503MPMW.
Did 2.6ghz@1.55V and load temps were 42°C on a 7700CU so the temps here are good.
Didn't try higher
My CAAZC 0442 does 2.75Ghz stable. I cant seem to go above 250Mhz though which is a pity.
so it looks to me like these clawhammer's aren't as good as they were supposed to be.
the clocks are similar to mine with th oldcastle on s754! an this chip is about 1 year old......
well......nice clocks anyway.
mfg
I'd like to know just how accurate my temps are. Does anyone have experinence in making one of those thermisters that you can build from radio shack parts? Where would they be plugged into on the MB? I've been downloading some 25 files on winmx and defragging and playing a small portion of games all night and MB monitor shows my high was 50c and is now running at 46c. Ambient is 26.
Would the power supply always be above the rest?
Readings now:
PWM 52c
CPU 46c
Case 41c
Highs were:
PWM 55c
CPU 52c
Case 42c
MB monitor does not show support for an Abit Av8 or any of the new motherboards, even with an online update??? I had to select Some other abit motherboard.
Well, I'm at 260x10 @ 1.472v, 24/7 and gaming stable with AMD HSF. I think that it's an excellent processor.Quote:
so it looks to me like these clawhammer's aren't as good as they were supposed to be.
the clocks are similar to mine with th oldcastle on s754! an this chip is about 1 year old......
I think that PWM or PWMIC on my DFI is for the mosfets temp!!Quote:
Would the power supply always be above the rest?
ha that's the exactly same v-core i need to archieve 2,6ghz!Quote:
Originally Posted by Kosmic71
i designed a little graphic to show the volt/mhz-relation.
i'll post it the next few days!
mfg
Nice, I can get one from a local store :)
THe only issue is, is it worth it with San Diego comming out?
I just love this processor, but wait for Venice/SanDiego.
I will test it with water first and maybe put it for sale to get a 3700+
SD.
I'm curious to see it, but, it will be related to your processor only.Quote:
i designed a little graphic to show the volt/mhz-relation.
Just an update. http://valid.x86-secret.com/show_oc?id=15506 On stock cooling. Not prime stable by any means. But 3d01 stable. max prime stable is currently 228 x 11 @ 2-3-2-5
I have a plan on check the accuracy of my cpu temps:
I am going to buy this part from svc:
http://www.svc.com/hsc-u01-e1.html
schematics, (see pdf) http://www.100y.com.tw/product/19717.htm (PDF)
http://www.shrs-ic.com/e_new/e_new6.htm
What I plan on doing is obtaining a pure copper metal sheeting/shim such as:
http://www.ksmetals.com/HobbyMerchan...ural_sheet.asp or
http://www.jewelrysupply.com/EJS/sssheet.htm
other possibilities are:
CuAg alloy (copper 28% + Silver~78%, Ive found very little about this alloy and from what i've read it has better thermal characteristic than pure silver)
Sterling Silver (but I havn't found what the thermal properties of this are yet)
Pure Silver
I will dremmel a 7mm x 2mm cut-out from the edge of a 2 sq inch sheet of the above. The thickness of the sheet/shim will be ~0.5mm. The sheet is placed on top of the cpu with ac5, thermistor added, and heat sink above it.
The thermister will only extend ~7mm into the cpu. Based on memory I think this would be about 1/4 into the core area.
The only problem I see is the sheet/shim not being finely sanded enough and the correct height of the shim.
Hopefully this way, the cpu temps will read more accurately and reduce constantly swinging misreads.
up to 2805mhz (255x11) 3d01 and SPi 8M stable with 2-2-2-6 timings. :banana: i have reached my goal and now just have to burn this stuff in to make it 32M stable. 1.63vcore and 3.61vdimm FWIW.
Nice :D this is my goal also, are u running on water?
I'm presently at 260 x 10 @ stock voltage 2.5-3-3-7 @ 2.8v 1T
ouppsss! just saw it in your sig!! he! he! :rolleyes:
havent updated the sig yet. Running an XP-120 with a 38mm high speed panaflo. 1.63vcore, 3.61vdimm :)
CAA2C 0509 DPMW
2.7ghz prime stable 7hours
1.275x126% = 1.60vcore
i smell 2.8-2.9 coming..
watercooling coming soon.. :D
San Diego ???? whay so special about it....minimal
Nice speeds man! Our DPMW's rock! :toast:Quote:
Originally Posted by babyelf
What kind of ram are you running? if its BH-5/UTT, care to post a shot of your settings? Having some issues with my BH-5 atm
i have some 3200LLv1.1
260 prime stable memtest passed 15 loops (quick test) at 3.3V
3.2V up to 240mhz
3.3V up to 260mhz at the moment
A64 tweaker settings.. (i set all in bios not in the tweaker)
http://img.photobucket.com/albums/v3...260mhz2225.jpg
SuperPi 32mb (28m 18.703s) the superpi window not long enough lol
http://img.photobucket.com/albums/v394/babyelf/pi.jpg
Sandra bandwidth
http://img.photobucket.com/albums/v3.../260sandra.jpg
my proc 2700mhz prime
http://img.photobucket.com/albums/v3.../2700prime.jpg
going to burn in tonight 260 3.3V with memtest.. hopefully everything goes well
will wait for watercooling to come before i push higher on the processor
I've got mine running at 260 x 10 atm with stock voltage (1.456v cpuz) prime
stable, SPi 32M 3DMark03,05 and my temp is pretty high Idle: 43C load: 53C
ambient: 19C, stock HSF.
I tought that temp was directly proportonal with voltage. It seams that temp
goes up with faster speed even tho the voltage is at stock. can someone
give me more info this? thanks
the more clock cycles the more heat you produce, simple.
Working on my CAA2C 0509CPMW. Had it running at 2.4GHz (300MHz x 8.0) at 1.367V (1.40V BIOS). Right now testing at 2.7GHz at 1.48V (1.50V BIOS). Thinks are looking good. Will post bench pics as soon as I get to my final speed and certify it stable.
Late to the party as usual but I just got a hold of one today as I'm upgrading my brother's rig for him...
Changing from 3.2"C"/IC7-Max3 to 3500+/K8N Neo2 for him so I get the chance to test this baby out on either the DFI or MSI boards to see which one OC's better...
Maybe my luck will change & I'll get past 2.5GHz...
Good thing is, whichever is the better OCer I get to keep as my brother's a bit boring.... Likes to run things at stock unless I OC it for him...
Back with some good results hopefully...
Damn shame I can't get a hold of a Venice/San Diego from our supplier down here in Melbourne, Australia...
Minh
screeny of my setup. 255x11 (2805mhz) finally got my BH-5 to comply a little bit. 8M stable atm...going for 16M after some burn-in. :)
That is exactly where I'm at with my "0508", but with an XP-90C.Quote:
Originally Posted by boostdfd3s
Using a Vdimm modded Epox NF3, with Mushkin PC3500.
32M SuperPi passes.
Any reason to get one of these over a Venice/diego now really? Other than maybe if you plan on putting it under a cascade.
Mushkin PC3500 BH5? 2x512mb? post your settings :toast:Quote:
Originally Posted by serlv
i made this whit the stock coller...
it´s a 09 week ...
http://img55.echo.cx/img55/39/screenhunter0045ev.th.jpg
http://img55.echo.cx/img55/7217/scre...r0031zz.th.jpg
i´m waiting for my r404a prommy to tested it.
2700mhz undervolted, nice :) How stable is that though?
No, 256x2.Quote:
Originally Posted by boostdfd3s
Using 3.41 VDimm, 1.63 VCore
BIOS/A64 settings shown below.
I'm still trying to learn A64 tweaking. Any suggestions or hints?
http://www.xtremesystems.org/forums/...id=30026&stc=1
in bios set ur us rating to 3120 set it to 15.6 us in a64 tweaker, it's more efficient
Huh? Which setting? Not getting you.Quote:
Originally Posted by i found nemo
I'm not using an NF4 w this chip, so I don't think of seen that setting in my BIOS. Or in A64 tweaker. Which setting?
he means the refresh rate (tref), might not have it in you rbios or it could be caleld something else, what mobo?
Epox 9NDA3+
Serlv, identical vcore here at 1.63v....nice on the vdimm though. I had to use 3.5v and burn in extensively to get it half stable! :toast:
Probably related to the fact they're 512s... Maybe.Quote:
Originally Posted by boostdfd3s
I had 'em up to 274 @ 3.6, but, of course, I can't run the 11 multiplier with that FSB. So, I can't get the overall clock as high. It didn't seem to make a difference as far as SPi went either, at least as far as 1M. So, I figured let me back off the volts a touch and run them a little slower. A program I run 24/7 seems to benefit from total mHz, and as you know, the system doesn't seem slow where its' at. ;)
Just want to add this to the thread, stock voltage and HSF.
http://img268.echo.cx/img268/4913/26...vspi32m4jz.png
I'm up to this on water. My personal record. :p:
Do you guys think I can go higher than 1.7v Vcore without danger to the CPU?
http://img284.echo.cx/img284/9340/29...esized704n.jpg
I know it's old but that printed out motherboard is just classic.Quote:
Originally Posted by s7e9h3n
:rofl:
default
http://img52.echo.cx/my.php?image=defaut5rp.jpg
and whit 1.84v
http://valid.x86-secret.com/show_oc?id=19977
WoW! :eek: babyelf and MadMog :toast:
Can you guys show me your BIOS settings for getting stable at those speeds?
Hardware and cooling also?
Thanks
u want a picture or just the settings?
260x11 = 2860
vcore
1.4 x 123% = 1.722
bios shows 1.67
ram at 2-2-2-5 3.5v
LDT multiplier at x3
Vldt 1.3
Vchipset 1.7
same for the below picture
cooling
http://img.photobucket.com/albums/v3...f/DSCN2444.jpg
XP120 & sunon 108CFM on CPU
Vantec Fan Card blowing on Dimms
The more informations the best! :p:
Thanks for your help. :toast:
Kos
erm.. what other info do you need?Quote:
Originally Posted by Kosmic71
bios is 331-2
Yep, I run my 3500+ 130nm with 1.9VQuote:
Originally Posted by Kosmic71
- SP8M @ 1.9V
- SP1M 1.77V :D
now that is sick....Quote:
Originally Posted by Dani
Everything looks to be there :p: Vcore, Vchipset, VLTD, FSB, multi, LDT/FSB ratio, BIOS etc thank you much.
The 32M at 2860 MHz impressed me!! :woot:
I think I've got a good cpu, 3 things prevent me to be SPi 32M stable @ 2.9.
1. I don't have active cooling on my RAM, Panaflo high RPM 90mm just arrived so I should be good now! :D
2. I'm still with 310 bios, I will try 331 414 and 510 I'm looking forward to 510
3. I'm running a SLI setup, I don't think its good for OCing.