K32A You can only change the multiplier if you have only ONE Stick of ram in your dimm slots
Printable View
K32A You can only change the multiplier if you have only ONE Stick of ram in your dimm slots
I do only have ONE stick! Maybe i should try another slot. Right now it's in slot 3. I will try to set it in slot 1. But thanks for the information anyway ;)
with clockgen mine changes with two sticks... just doesnt retain the setting after reboot, goes back to 10.Quote:
Originally posted by EmineM
K32A You can only change the multiplier if you have only ONE Stick of ram in your dimm slots
edit: I have SMD grabbers, gotta pick up that variable resistor though.
If I set my MP lower with clockgen, my PC locks.Quote:
Originally posted by SupaMan
with clockgen mine changes with two sticks... just doesnt retain the setting after reboot, goes back to 10.
edit: I have SMD grabbers, gotta pick up that variable resistor though.
But is remember the setting until I turn my PC off.
SupaMan GlockGen is designed to restore your bios defaults at the next boot. So if your bios is 200FSB and you have 3200+(10x) and you set GlockGen to 250 x 9.5 then it WILL reboot at 200 x10 (default).
My system will also change with two sticks in either of the three slots BUT the Gigabyte boards love the mem in the 3rd slot for some reason. Give it a try, I did and got over 10FSB higher just by doing that!
3rd slot eh? ok I'll give it a go. I tried with just one stick (in slot 1) and it didnt really help with anything at all.Quote:
Originally posted by andyddr
SupaMan GlockGen is designed to restore your bios defaults at the next boot. So if your bios is 200FSB and you have 3200+(10x) and you set GlockGen to 250 x 9.5 then it WILL reboot at 200 x10 (default).
My system will also change with two sticks in either of the three slots BUT the Gigabyte boards love the mem in the 3rd slot for some reason. Give it a try, I did and got over 10FSB higher just by doing that!
I figured clockgen wasnt supposed to keep the setting... would really screw people over if they picked a bad one if it did
I was wondering how you guys can get such a high FSB, when the PCI/AGP lock don't seem to work proberly....?
Are you just lucky that it works on that time, when you are clocking, or does it have something to do with a newer BIOS..? :confused:
Mostly luck, and using PCI devices that happen to tolerate such speeds.Quote:
Originally posted by Matshui
I was wondering how you guys can get such a high FSB, when the PCI/AGP lock don't seem to work proberly....?
Are you just lucky that it works on that time, when you are clocking, or does it have something to do with a newer BIOS..? :confused:
I have recently discovered that it sometimes work adjusting your AGP speed throug ClockGen, atleast when I tried another time earlier, the AGP speed stayed and even went down when I clocked my CPU back to the stocj settings again...
Also before my AGP speed had no trouble staying at 66/33Mhz, without adjusting it, and then suddently it won't lock anymore... :confused:
But if that thing with ClockGen works, then it is no problem anymore... :banana:
when you guys say the pci/agp lock doesnt work? what speeds does it stop working at? so far mine has stayed working but ive only got it as high as 240 so i probly havent got to the point where it stops working yet?
peace perc,
they dont work at any speed :)Quote:
Originally posted by Perc
when you guys say the pci/agp lock doesnt work? what speeds does it stop working at? so far mine has stayed working but ive only got it as high as 240 so i probly havent got to the point where it stops working yet?
peace perc,
your software isnt accurately reporting the speeds, to really see them you need a hardware PCI device tha measures them. Look at the anandtech article about this for some good information.
Quote:
Originally posted by SupaMan
they dont work at any speed :)
your software isnt accurately reporting the speeds, to really see them you need a hardware PCI device tha measures them. Look at the anandtech article about this for some good information.
what's the max frequency that you can hit with this cg core supaman? passing burn tests i mean..
crappy... 2.3GHz @ 1.7VQuote:
Originally posted by eviLRuLeZ
what's the max frequency that you can hit with this cg core supaman? passing burn tests i mean..
I'd love to think it's the motherboard, or the memory, but I've managed to rule out both as the issue. The core just wants more juice. Isnt overheating either.
erm ok .. :/
maybe that cpu isnt that good.. i mean the cpu that you received from amd.. but others core cg may be good probably
we'll see that in a little while i hope ;)
ok guys i have had my 64 3200 system now for a week and i think i got the hang of it? right now i can run the system at 230x10 @ 2300mhz v-core 1.55v memory 2.9v everything else auto. now i am ocing thri the bios cause it seems more stable this way? also i had a question about the LDT settings? i had it set to 2x and it ran prime stable so i tired 2.5x and for some reason it shows up in sandra like its still set at 2x plus the memory scores stayed the same? i run the an50r with the an50s00y bios can anyone shed some light on this? also is 2300mhx at 1.55v decent for the 3200 chip?
thx guys perc,
yes
but did you try to hit a higher frequency? higher than 2300..?
1.520 is original voltage for the cpu isn't it?
try to determine where your cpu is stable without changing his voltage and tell us :D
and then tell us what max freq that you can hit with that beast plz :)
yes that soud good Perc. 2300mhs for 1.55vcore is better than any chip i've run before. did you get the stepping before mounting it?
see thats the thing guys when i first got this thing it wouldnt do 2400mhz stable infact im not even sure if it will now? i did have a suicide shot of it at 2400mhz but it rebooted like seconds after i finshed getting the screen shot!! i have been running it at 220x10 for the last week then i decided to oc thru the bios since i wasnt getting all the great of ocs. thats when i tried 225x10 and finaly 230x10 and so far its prime stable and seems rock solid so im just going to leave it at 230x10 for a few weeks to let it burn in real nice :D my voltages are v-core 1.55v (*in the bios windows reports them as 1.52v) memory 2.9v agp 1.60v chipset 1.9v and my LDT auto set to 2.5 (i see no differance from 2x?) here is the stepping of the chip....ADA3200AEP5AP CAAAC 0345RPMW 9457135K 30810 i have only see this stepping once or twice before in this thread. infact when i first got it i thought i had a dud cause 2250-2300 was all i could get and that was using 1.7v on the v-core then i got mad and just set the v-core back to 1.55v and ran it at 220x10! thats how i found out i could run 2300mhz at 1.55v. i had no idea this was good kinda why i asked.... ok guys once again thx for your help you guys rock :D oh one more thing? LDT 2 or 2.5? im running 2.5x now and it doesnt seem any faster then 2x? thx...
peace perc,
2.5 is good except around 300fsb maybe go 2x
edit: actually that's what gigabyte does. i havn't ever had a shuttle that fast
Perc
push that cpu to the limit now ! :D
oh i will not to worry man im not afriad :D just rember guys im on air....Quote:
Originally posted by eviLRuLeZ
Perc
push that cpu to the limit now ! :D
peace perc,
:(
you're on air... i thought you were on watercooling or phase change :(
cya ;)
edit: i can't put an avatar in my signature, why? i mean i can't import a picture..
can you help me?
WOWWW
361.13 and an 8 multiplier
impressive!!!!
TimeF0•ª30•b
Clock(MHz)F2889.02MHz(361.13x8.0”{j
CPUiƒƒbƒgî•ñjFAthlon64 3200+@CAAMC0343WPMW
—â‹pF“º“’“Û•ƒhƒ‰ƒCƒAƒC ƒX+ƒGƒ^ƒm[ƒ‹
VcoreF1.89V
VddrF3.36V
VioF3.70V
M/B(Chip Set)FGIGABYTE K8Npro (nForce3)
MemoryFSanmax BH-5 256MB
HDDFDeskster IC35L080
OSFWin2k SP4
http://www10.ocn.ne.jp/~leader/3200_11.jpg
Just got my 3400+ setup.
Stepping is ADA3400AEP5AP
CAAOC 0351UPMW
9835134L30351 - Malaysia.
Anyone know if this is a nice stepping or will i just have to find out for myself;-)
find out yourself :) the week 0351 chips seem to perform well
Hey im running the Gigabyte k8n (non PRO and non XP).
Im still running with the "stock" BIOS, because i haven't read about them too much. Is there a BIOS availeble wich improves performance?
Pejsen you can use lower multis and chaneg them in the bios instead of crappy clockgen and doing it time you boot by flashing the gigabyte ga-k8nnxp-940 bios :) it works without a hitch!
hey can someone link me to the k8npro vmod
Hey PhyroxQuote:
Originally posted by Phyrox
hey can someone link me to the k8npro vmod
thx for the help, i will defenently load new BIOS tomorrow :)
As for the Vcore mod: http://www.xtremesystems.org/forums/...threadid=20190
Very easy mod, indeed. I used a grabber on the IC pin10 and used the one of the motherboard "mountingholes" as GND (ground).
Notice that u should set Vcore at AUTO in BIOS or else u will risk loosing your CPU. Set the VR @ 50K ohms and turn slowly too increase the Vcore, please note that you should be carefull, at a certain point voltage grows ekstremly fast, so first time i tried i ended at 2.05Vcore HEHE. :e
However the K8N has an internal safety-thing that automaticly shuts down the board when Vcore is over 2.1V - been there, done that :p:
Ps. sorry for bad english
cpulloverclock...
You are one wild and crazy guy with those voltages. Even
with a Vapo.
You have the Fire Department standing by with a Hook &
Ladder crew?
I read somewhere a while back.... that if a guy will leave the
FSB set at 201 in BIOS the AGP/PCI will remain locked while
using Clock/Gen. At least above 200 which is default.
I found out this works for me as the first time I tried Clock/Gen
I had to go back into BIOS and make the change to get a lock.
This is with a Shuttle AN50R but I don't see why it wouldn't
be the same for any nForce3 150 board.
;)
Did I do good :D
andyddr how much voltage is going to that memory? I take its KHX3200 BH-5?
Bennah there`s a mere 2.95v flowing thru these babies...want to guess again?
Err okay no-one wants to play `guess the ram` with me?
It`s A-Data Vitesta.
And no : look my config...geil is good ram?
ldlc
Processeur AMD Athlon 64 3200 229,93 €
Disque dur Hitachi 160 Go 7200 RPM 8 Mo Serial ATA 98,62 €
Alimentation Fortron 350W 44,27 €
Zalman CNPS7000A-Alcu 30€
o/c.UK
Sapphire ATI Radeon 9800 Pro 128MB DDR TV-Out/DVI - Lite Retail (GX-017-SP)
£131.25 £131.25
Arctic Cooling VGA Silencer (SY-000-AR)
£6.50 £6.50
GeIL 512MB (2x256MB) PC4200 Ultra Series CAS3 (GL5124200DC) (MY-022-GL)
£96.12 £96.12
GeIL is not bad.. I personally prefer the Geil PC 3700 but personally I would rather buy some Kingston bh5 sticks
http://www.overclockers.co.uk/acatalog/GeIL_memory.html
...what is the best?
Please dont spam.. theres an EDIT option that allows you to edit your previous post
GeIL 512MB (2x256MB) PC3500 Ultra Series CAS2
eminem, sorry:stick:
Guys what you think of this overclock? It`s done on air with a TT Venus 12 @ 3500RPM and 19C ambient air temp. No-matter what I do I can`t get over 2500 out of it even at 1.95v. Do you think if I phase change it`ll be a good clocker?
See steppings in my sig!
Is that board voltmodded at all?
Yip Vmodded on CPU only.
Very nice oc then! :)
My 3200+ won't go anywhere near 2400mhz, could you tell me what psu your using and what volts the rails are reading?
According to the manufacturers of MB, the Socket 939 (MB and Proc) would be available at the end of may or at the beginning of june :mad: = ESTIMATE
lil old me I`m running a VERY crappy 350Watt PSU and MB5 says my rails are around 3.1v.
Guess i got a bad chip and you got a good one then! Our rigs are very similar but i cannot get past 2300mhz at 1.7v :(
Well post your steppings so we can have a look. May be that your cooling, RAM or even PSU is holding you back and not the chip...always the optemist
I cant get any higher than 10x230 at 1.65 vcore, 1:1 2-2-2-5 2.7v - Is that good or bad?
Unfortunatly i didnt write it down and cant look until sat.Quote:
Originally posted by andyddr
Well post your steppings so we can have a look. May be that your cooling, RAM or even PSU is holding you back and not the chip...always the optemist
However my cooling stock hs with 120mm ys tech 45C full load, ram kingston pc3000, psu is hiper 350watt, it seems to fluctuate and i thought that might be what it was but if yours is ok with a bad psu it might not be the problem.
i think it's bad because you'd better decrease mutiplier ; and increase FSB , if your sticks don't support 255mhz, increase vddr to 3,3v (easy with AN50R) and pump up the FSB !!Quote:
Originally posted by K32A
I cant get any higher than 10x230 at 1.65 vcore, 1:1 2-2-2-5 2.7v - Is that good or bad?
9X255 FSB 1:1 would be very easy and much better.
8X287 FSB 1:1 a little higher , i think ; but if you'll do it ; i'll applause you ;)
I can't change my damn multiplier :( Every time i change it from BIOS it's set back to x10 when i come into Windows :( And with clockgen my computer freeze :(
What is the problem ?
set your LDT to 2,5X
Make sure you click on `get values` before you change your multiplier settings. Once you change it click `apply FID` and then `set values` and your system should`nt freeze anymore.
Hey!
I've just tried that in clockgen, it seems to work fine if i set the multi to x9 and apply it, but when i want to run 2000MHz it freeze's x(
It is really p*ss*ng me off :(
try to clearcmos and retry. :/
or try to set to 230X10 and set multiplier to 9.
LDT to 2,5X or 500MHZ
Take it up SLOWLY....don`t jump from say 200FSB to 230FSB in one jump, rather do it in 15MhZ intervals. Also (VERY IMPORTANT) set your FSB to 210 in the bios and then play in ClockGen. For some reason it like the system a bit overclocked before you push it further.
Also your Mem voltage may be too low. Try more juice...say 2.9v and see if it helps.
i'd buy a 3000+ Today , an 0350 XPMW CAATC
http://pageperso.aol.fr/misteroadster/3000MAX.JPG
i think i can do better.
french touch
3ghz now ^^
Nice CPU man! :thumbsup:Quote:
Originally posted by misteroadster
i'd buy a 3000+ Today , an 0350 XPMW CAATC
http://pageperso.aol.fr/misteroadster/3000MAX.JPG
i think i can do better.
What cooling? Chilled water?
yes, watterchilled
I just got my D-tek Pro-core and a Hydor L20 home today, now i'm just waiting for my homemade waterblocks for cpu and gfx, and my little Biostar IDEQ200P Barebone :P It's goig to be fun ;) How high do you think i can get my cpu?
Do some benches, or is this a critical shot???Quote:
Originally posted by neo.life
yes, watterchilled
nice thing btw... I have a CAATC 0404XPWM and I can take a shot from 2800Mhz.
These are nice chips :cool: 2550Mhz stable with 1.68v (Asetek water) :banana:
Humm les xpmw are good ^^
I buy too in 3000+ mister shop ( e-soph ) and i send a mail for stepping...
waiting responses et after gogogo ( adata4000 +an50rand tm 948U )
you mean extreem good.Quote:
Originally posted by neo.life
Humm les xpmw are good ^^
I buy too in 3000+ mister shop ( e-soph ) and i send a mail for stepping...
waiting responses et after gogogo ( adata4000 +an50rand tm 948U )
Most XPMW can do 2500MHz stable in air/water and 2600MHz with chilled water.
I had a:
CAAMC 0449RPMW = 2250MHz max @1.8v:mad:
CAAOC 0350XPMW = 2550MHz max stable @1.79v
CAATC 0404XPMW = 2550MHz @1.70v still OCing
Lucky XPMW can do 2700MHz.:)
All with WATER and AIR.
I can get a 3000+ CBAPC 0404UPMW (CG stepping) :D
For me this
CAATC 0404XPMW = 2550MHz @1.70v still OCing
lovely !!!!
I buy thrusday my computer :D
Core cg is not very good for o/c
2.3ghz ( reviews of 3000+ in english site )
i think, i prefer good C0 of bad CG
hehe, :toast: this chip we have clocks realy good with prommie.Quote:
Originally posted by neo.life
For me this
CAATC 0404XPMW = 2550MHz @1.70v still OCing
lovely !!!!
I buy thrusday my computer :D
Core cg is not very good for o/c
2.3ghz ( reviews of 3000+ in english site )
i think, i prefer good C0 of bad CG
It can take high speeds :D
Unfortunaly it is not a lucky chip but a good performer
Waterchilled by this machine :Quote:
Originally posted by Zeus
Nice CPU man! :thumbsup:
What cooling? Chilled water?
http://pageperso.aol.fr/misteroadster/CHILLON.JPG
Thanks ;)
But i hope better tomorrow :)
Weee..... I also have the CAATC 0350XPMW, not a CAAOC as I first remembered (I have a bad memory), until now I have not clocked it higher than 2300Mhz air cooled with stock voltage, will have my watercooling set up in the weekend hopefully, so let's see what my 0350XPMW can do, those 2900Mhz is just lovely... :slobber:
i fly so highhhhhhhhhh
i'm flying right up to the stars :D
i want more FSB... 400 and more, tips ?
http://downhill666.bei.t-online.de/R..._345_small.gif
worthless running on 400HT...
i just receave my shuttle an50R
http://www.yamafoto.com/users/niaboc...80-2-2-2-5.JPG
good job my friend ;)
:toast:Quote:
Originally posted by misteroadster
good job my friend ;)
It seems to work fine with decreasing the multiplier to x9 now. I dont know what the problem was?
240x9 1:1 2.9v to the memory, Auto timings :( I had just cleared CMOS and then i forgot to set the timings :$
I dont know if my memory can get higher?
your problem was the timings , dont worry !!! ;)
you have to adjust now and obtain the best compromise.
280fsb 1/1 on 2-2-2-5 timingsQuote:
Originally posted by niaboc79
i just receave my shuttle an50R
http://www.yamafoto.com/users/niaboc...80-2-2-2-5.JPG
OH MY GOD how much vdimm on that (probably) BH5 memory?
(why didnt you reply about our deal with the 3ghz barton)
280 on BH5/6? WTF?
Wow that is really good dancing bananas!!!
280 with BH5 corsair @ 3.7Vdimm ;)
PC3200 LL rev. 1.1 or PC3500 C2 rev. 1.1 ?Quote:
Originally posted by neo.life
280 with BH5 corsair @ 3.7Vdimm ;)
weeee, 3 GHz screenshot ^^
Not stable at this speed, max stable is 2.85 GHz.
Might try to get 2.9 GHz stable on 2.0v next time.
pics of setup: http://users.pandora.be/alz/dryice64/
CPU: CAATC 0405 VPMW
This is what I don`t get...all 3000+`s are Newcastle and the 3200+ and 3400+ are ClawHammer right? Well then why is post #2`s 3000+ (previous page) showing as a ClawHammer?
Link
Because it's an older version of CPU-ZQuote:
Originally posted by andyddr
This is what I don`t get...all 3000+`s are Newcastle and the 3200+ and 3400+ are ClawHammer right? Well then why is post #2`s 3000+ (previous page) showing as a ClawHammer?
Link
Yes.Quote:
Originally posted by misteroadster
your problem was the timings , dont worry !!! ;)
you have to adjust now and obtain the best compromise.
I will try later... Maybe 2-3-3-6 will work?
K32A are you sure GeIL PC 3700 are able to run 2-2-2-5 as you are saying on your sig? I highly doubt it
PC3200LL rev 1.1, it's BH5Quote:
Originally posted by SKYNET
PC3200 LL rev. 1.1 or PC3500 C2 rev. 1.1 ?
my barton give me only 35sQuote:
Originally posted by koensa
280fsb 1/1 on 2-2-2-5 timings
OH MY GOD how much vdimm on that (probably) BH5 memory?
(why didnt you reply about our deal with the 3ghz barton)
3.7v
My A64 3200+ is now at 2740MHz, 3D-benchable
http://hk-submit.no-ip.com:2/bbs/att..._3200+2740.jpg
At 2790MHz, superpi1M completed.
http://hk-submit.no-ip.com:2/bbs/att...790superpi.jpg
20MHz more than before :D
tintin can you tell me where ya got oyur wallpaper??
and as always nice clocking my man :)
Tin tin that 3dmark01 score is 1000 marks low . compare to my score below sig
edit: nm you are running ddr 333 setting
Yes, i run at 2-2-2-5, 2.7v now ;)Quote:
Originally posted by EmineM
K32A are you sure GeIL PC 3700 are able to run 2-2-2-5 as you are saying on your sig? I highly doubt it
Wee, got my cpu up to 2400MHz, but my memory could'nt handle it at 1:1 so i just ran it at 2:1
Reason:Quote:
Originally posted by yuri
Tin tin that 3dmark01 score is 1000 marks low . compare to my score below sig
edit: nm you are running ddr 333 setting
1) Windows 2000 + DX 8.1 will have about 500marks more
2) The Game 1 low details always has some fluctuations in the frame rate, if you run this test for, say, 10 times, you will see at least, there is a score have about 20fps in average more for the same setting :D
3) You are running your CPU/RAM at 1:1 ratio
Totally, 1000marks...hahaha....
:D
Hey!
I hope that you guys can help my friend ;) He's just got a A64 3200+ caaoc 0352spmw but it will not go higher than 213x10!!! Can any one of you get some data on that chip for me?
Greets
A64 3000+ 0350 XPMW CAATC AEP4AP 9
Just Waterchilled.
http://pageperso.aol.fr/misteroadster/2958screen.JPG
I can do better , a little , .... but better :D
I am testing an FX-53 actually. :rolleyes:
cooling AMD Boxed :
stock vcore: 2510 stable prime 95
1,65V: 2580 stable prime 95.
max screen 2749 Mhz@1,65V
http://pageperso.aol.fr/misteroadster/MAXaircool165.JPG
http://pageperso.aol.fr/misteroadster/prime2588.JPG
I can do very very very Much better :D
wow
impressive mister :D
mister,
with the cooling box fan it's: :banana: :D
Waterchilled FX53 : Rock Stable Prime 2960Mhz 1,85Vcore.
But cpumark and superpi 2M doesn't work , i think there is a problem with my ram Corsair Ecc 3200 (CH5).
http://pageperso.aol.fr/misteroadster/3156.JPG
try with 2v for 3.2G
between ur FX-51 and FX-53 there are 100MHz at same voltage
I see 3275MHz rock stable in cascade for Tom Holck
:D