BuGjAE and Ghostleader,the system temp reading you see in ET6 is not the NB temperature. it seems that the system temp sensor is located near the SB heatsink.i dont think you can tell what the NB temps are unless your on WC and have sensors hooked up.
ok here a template for 4GHz and 4.5GHz for now still working on a better 4.6 and 4.7, there really touchy:D
4GHz real voltage is 1.232v idle and 1.184v load
[/QUOTE]PHP Code:******Gigabyte EP45 UD3 Template*******
[B]4.00GHz[/B]
Robust Graphics Booster [auto]
CPU Clock Ratio [8x]
Fine CPU Clock Ratio [+0.5]
**********Clock Chip Control***************
CPU Host Clock Control [enable]
CPU Host Frequency (Mhz) [471]
PCI Express Frequency (Mhz) [100]
C.I.A 2 [disable]
*********Advanced Clock Control**********
CPU Clock Drive [800mv]
PCI Express Clock Drive [800mv]
CPU Clock Skew [0ps]
MCH Clock Skew [0ps]
*******DRAM Performance Control********
[B]ram is set low cause my ram sucks:D[/B]
Performance Enhance [turbo]
Extreme Memory Profile (XMP) [auto]
(G) MCH Frequency Latch [auto]
System Memory Multipler [2.00B]
Memory Frequency [942]
DRAM Timing Selectable [manual]
CAS Latency Time [5]
tRCD [5]
tRP [5]
tRAS [15]
*******Advanced Timing Control***********
didnt touch ram timings auto
tRRD []
tWTR []
tWR []
tRFC []
tRTP []
Command Rate (cmd) []
***********Motherboard Voltage Control*******
Load-Line Calibration [disabled]
CPU Vcore [1.275V]
CPU Termination [1.24V]
CPU PLL [1.57V]
CPU Reference [0.825V]
MCH Core [1.34V]
MCH Reference [0.825v]
MCH/DRAM Refernce [0.950V]
ICH I/O [1.570V]
ICH Core [1.100V]
DRAM Voltage [2.120V]
DRAM Termination [auto]
Channel A Ref [auto]
Channel B Ref [auto]
Channel Timing Settings [B]didnt change[/B]
Static tRead Value []
tRD Phase0 Adjustment []
tRD Phase1 Adjustment []
tRD Phase2 Adjustment []
tRD Phase3 Adjustment []
tRD 2rd (Differnt Rank) []
tWR 2wr (Differnt Rank) []
tWR 2rd (Differnt Rank) []
tRD 2wr (Same/Difft Rank) []
Dimm 1 Clock Skew Control []
Dimm 2 Clock Skew Control []
DDR Write Training []
Channel Driving Settings
Drive Strength Profile []
Data Driving Pull Up Level []
cmd Driving Pull Up Level []
ctrl Driving Pull Up Level []
clk Driving Pull Up Level []
Data Driving Pull Down Level []
cmd Driving Pull Down Level []
ctrl Driving Pull Down Level []
clk Driving Pull Down Level []
*****************Advanced BIOS Features*********
CPU Multithreading []
Limit CPUID Max to 3 []
No-Execute memory Protect []
CPU Enhance Halt (CIE) [disable]
C2/C2E State Support [disable]
C4/C4E State Support [disable]
CPU Thermal Monitor [enable]
CPU EIST Function [disable]
Virtualization Technology [enable]
4.5GHz real voltage is 1.408v idle and load LLC enabled
[/QUOTE]PHP Code:******Gigabyte EP45 UD3 Template*******
4.5GHz
Robust Graphics Booster [auto]
CPU Clock Ratio [8x]
Fine CPU Clock Ratio [+0.5]
**********Clock Chip Control***************
CPU Host Clock Control [enable]
CPU Host Frequency (Mhz) [530]
PCI Express Frequency (Mhz) [100]
C.I.A 2 [disable]
*********Advanced Clock Control**********
CPU Clock Drive [800]
PCI Express Clock Drive [800]
CPU Clock Skew [0ps]
MCH Clock Skew [0ps]
*******DRAM Performance Control********
Performance Enhance [turbo]
Extreme Memory Profile (XMP) [auto]
(G) MCH Frequency Latch [auto]
System Memory Multipler [2.00B]
Memory Frequency [1060]
DRAM Timing Selectable [manual]
CAS Latency Time [5]
tRCD [5]
tRP [5]
tRAS [15]
*******Advanced Timing Control***********
didnt touch ram timings auto
tRRD []
tWTR []
tWR []
tRFC []
tRTP []
Command Rate (cmd) []
***********Motherboard Voltage Control*******
Load-Line Calibration [enable]
CPU Vcore [1.44375V]
CPU Termination [1.420V]
CPU PLL [1.610V]
CPU Reference [0.899V]
MCH Core [1..520V]
MCH Reference [0.939]
MCH/DRAM Refernce [1.140V]
ICH I/O [1.570V]
ICH Core [1.200V]
DRAM Voltage [2.160V]
DRAM Termination [auto]
Channel A Ref [auto]
Channel B Ref [auto]
Channel Timing Settings [B]didnt change[/B]
Static tRead Value []
tRD Phase0 Adjustment []
tRD Phase1 Adjustment []
tRD Phase2 Adjustment []
tRD Phase3 Adjustment []
tRD 2rd (Differnt Rank) []
tWR 2wr (Differnt Rank) []
tWR 2rd (Differnt Rank) []
tRD 2wr (Same/Difft Rank) []
Dimm 1 Clock Skew Control []
Dimm 2 Clock Skew Control []
DDR Write Training []
Channel Driving Settings
Drive Strength Profile []
Data Driving Pull Up Level []
cmd Driving Pull Up Level []
ctrl Driving Pull Up Level []
clk Driving Pull Up Level []
Data Driving Pull Down Level []
cmd Driving Pull Down Level []
ctrl Driving Pull Down Level []
clk Driving Pull Down Level []
*****************Advanced BIOS Features*********
CPU Multithreading []
Limit CPUID Max to 3 []
No-Execute memory Protect []
CPU Enhance Halt (CIE) [disable]
C2/C2E State Support [disable]
C4/C4E State Support [disable]
CPU Thermal Monitor [enable]
CPU EIST Function [disable]
Virtualization Technology [enable]
just a side note but i was sometimes unable to use the same reference (cpu, mch, mch/dram) voltage based on the order i change the setting's and after reboot would sometime change the reference voltage above is after testing for 100% stable for hours and rebooting multiple times
hope this helps someone:D
cheers
I'm inclined to think that it's not the board. You've had 2 boards with different revisions and both with the same issue with 5 different sets of RAM. If the board was that picky, one would think this problem would be much more widespread.Quote:
Originally Posted by clo007
There is the fact that you've only used RAM from Crucial and G.Skill and , as I recall, others have had problems with Ballistix sticks, but I believe lots of people are using various G.Skill sets successfully.
I find it odd though that I can't run at stock speeds with 2 sticks of ram, but I can run with 1 stick at over 4ghz with ease. And there are quite a few people over at the tweaktown forums having the same issue as me.
How do you know what your NB temps are? There is no NB temp sensor. :shrug: :confused:Quote:
Originally Posted by SimpleTECH
thats what i was wondering?
It was 5 seconds after I found out that the sensor is for the motherboard, not the northbridge that I realized... opps..Quote:
Originally Posted by nugzo
Not having a good week so far. :(
question guys , im running f5 bios now on a EP45-UD3P , what difference does f7 make ?
i know the term if it aint broken . just wondering .
I'm really not sure what the "motherboard" sensor is measuring, but mine is at 33-34c always.
i tested it and it seems to be near the SB heatsink.
Hi, im thinking in buying the GA-EP45-UD3P with a Q9650, but Im stuck in deciding wich ram to buy! I want 8GB ram but Ive been reading this thread and people having problems with different ram just makes my head dizzy, can anyone tell me a stable ram that will run excelent on this board just by plug and play? Im not going to overcloak this rig, ill just run it stock. Thanks a lot.
G.skill pc 8800 PI are great if your running stock.the 9650 will run3.0ghz and memory will run ddr1066 with default settings.
im using 2 sets of theseQuote:
Originally Posted by faramith
http://www.newegg.com/Product/Produc...82E16820231145
at ddr2-800 speed they do 4-4-4-12 timings with 2.0v and ddr2-1000 5-5-5-15 2.0v as well
no problems with those sticks and my Q6600
Hey guys hopefully some1 can help me out here. When I disable LLC the annoying buzzing noise from the chokes was minimised dramatically but I BSOD after 2 passes of Intel Burn Test. With LLC enabled Im very stable. Any recommendations please?
Here are my settings:
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 8
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 3800
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 475Mhz
PCI Express Frequency (Mhz) .........:Set to 100
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800mv
PCI Express Clock Drive.................: <<< 900mv
CPU Clock Skew (ps)....................: <<< 0ps
MCH Clock Skew (ps)...................: <<< 0ps
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: Auto
System Memory Multiplier ..............: 2B
Memory Frequency (Mhz) ..............: 950
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................18
Advanced Timing Control
tRRD...........................................Aut o
tWTR..........................................Auto
tWR............................................Aut o
tRFC...........................................Aut o
tRTP...........................................Aut o
Command Rate (CMD) ....................: 2
Driving Strength Profiles
Driving Strength ............................Auto
Channel A
Static tRead Value.........................:9 Auto
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Channel B
Static tRead Value.........................:9 Auto
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Motherboard Voltage Control
Voltage Type. ... Manual
CPU
CPU Vcore . .........................:1.425
CPU Termination ..... 1.200V*.......: <<< 1.24
CPU PLL ....1.500V*.......: << 1.50
CPU Referen. ....0.76V*.......: <<< Auto
MCH/ICH
MCH Core .....1.100V...........: << 1.26
MCH Reference . .0.76V...........; <<< Auto
MCH/DRAM Ref. ......0.900V...........: <<< Auto
ICH I/O .....1.50V............: <<< 1.50
ICH Core ... 1.100V............: <<< 1.1
DRAM
DRAM Voltage ....1.800V............: 2.00
DRAM Termination . 0.900V............: <<< Auto
Channel A Reference 0.900V............: <<< Auto
Channel B Reference 0.900V............: <<< Auto
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
Specs:
E6750, Corsair xms2 pc6400 (2x1gb), tx-650 and ep45-ud3R
Raise vcore.
Thank you but I did already know that, that was why I asked BuGjAE about the temp, because I have a temp probe stuck inside the MCH heatsink and with LinX (with max problem size and max memory use) I get close to 50C@1,34v MCH core, I have not got that high in temp with any other test application so far.Quote:
Originally Posted by radaja
With 1,60v it should get pretty hot unless there is water to cool it or some other active cooling (fan).
With Everest I have to temp sensors, "Motherboard" and "Aux", Motherboard has the same temp as my CPU and Aux has temp 35-40C. Where they are located I don΄t know but I think that Motherboard are somewhere close to the PWM and CPU area and Aux close to the ICH area.
Ok ,thanks guy. I down it now. seem 1.60 vMCH doesn't help anything better.Quote:
With 1,60v it should get pretty hot unless there is water to cool it or some other active cooling (fan).
elite22 please tell me more about the MCH/DRAM reference. I was looking at your
templates and i understand all of your settings. I am stuck trying to increase my
fsb. I have messed with every setting on this thing except the mch/dram reference
I am assuming that you would just do it the same as all the other mch settings
ie... set it up to where memtest just starts to fail, and then start experimenting
with the mch/dram reference until it gets better or worse. I have never even
touched that setting. Does it have a dramatic effect (like the mch ref does) ?
Can you give me any hints?
Very nice cloking you do there. I like it. Impressive.
I want some stable high fsb action here. I seem to be stuck at about 515.
johnny168; I dont know anything about your particular chip, but on "my" chip the cpu term likes to be closer to the vcore to be stable.
Like maybe 1.4. But that is on a q9650. Maybe someone else can elaborate.
1+:), the 45nm like cpu term. get the term. closer to the vcore as said aboveQuote:
Originally Posted by mreld3r
Just playing, got cpuz val. Last day for ver1.49 is tonight. Will need 1.50. I tried to get it to run p95 @ 4.5 last night but only 18 to 20 min. I'm going to remove a set of rams and try again.[IMG]http://img293.imageshack.us/img293/4299/4645tq8.jpg[/IMG]
http://valid.canardpc.com/show_oc.php?id=508086
You can flash the bios UD3R with the UD3P? Gives any problems? Thanks and best regards
Hello, Using the Abit right now with E8500 and 2x2gb of Mush ram. Runs fine at 3.6ghz, temps around 31c (with zalman 9500) Since Abit closed the doors in the USA I wanted newer board if I can run 3.6ghz with the EP45-UD3R or EP45-UD3P I would be happy. PSU is PCP&C 750w. ANy problems you guys see with the ram or the cooler.
thanks
need help geing 500x8 4ghz stable i can bot in at 500 but prime fails on blend aftr 10 min. can someone post some settings to try think its my reference values
regarding this,Quote:
Originally Posted by BuGjAE
notice the vMCH/Ref needs track vFSB, once you change vFSB voltage
vMCH/Ref will track the value, so you need to give a set on vFSB & vMCH/Ref