Printable View
Yeah, I'll see if I have time to do it today..Quote:
Originally posted by zombie
Important is point 3-4 , so you must have all 16 pipes, or the 4 pipes are damaged without lasercut. The big i have also no contact.
I would flash the XT Bios and then look if you have 16x1.
It would be hyperXcool if I got 16x1 pipes then :D
or ultraYdown if it not work ;)
No one has flashed in the last 4 pipes yet? I think it will be a bummer. But yay if it works :D
OMFG!!!
I just did the pencil mod..
I set it from 1,41v to 1,45v as it was described in the vr-zone guide..
It went well for 10 min ,and then, the whole screen totally :banana: :banana: :banana: :banana:ed!
So I took away all the led, and turned the pc on..
The volt was back to normal (1,41v), but the screen is STILL TOTALLY :banana: :banana: :banana: :banana:ED!!!
Help me!!
RMA time.Quote:
Originally posted by Kasp2k
OMFG!!!
I just did the pencil mod..
I set it from 1,41v to 1,45v as it was described in the vr-zone guide..
It went well for 10 min ,and then, the whole screen totally :banana: :banana: :banana: :banana:ed!
So I took away all the led, and turned the pc on..
The volt was back to normal (1,41v), but the screen is STILL TOTALLY :banana: :banana: :banana: :banana:ED!!!
Help me!!
Shouldn't run more than 1.4 volts on an aircooled card.
It was running at 1,41 @ std....
So I only brung it up by 0,04v..
Then you should not have raised your voltage. Mine was 1.29 stock and it was a $hit overclocker, so I penciled it to 1.4, but not even 1/100 (.01) more.
Did you calibrate your volt meter on a 1.5v battery or something to make sure it reads correctly? If not, depending on the scale you were reading you may have put more volts into it than you think. Anyway, you have killed your card.
Clean it up really good and RMA it.
One thing, I checked the ohm's now.., it was reading 383ohm, is this std on the X800PRO @ the R1597 chip..Quote:
Originally posted by StormPC
Anyway, you have killed your card.
My Powercolor have 1.41Vgpu and 2.02Vmem. The Pencil Method is the stupid methode i know, no control. take the pencilgumm and erase all on the smd resistor.
You can't accurately check the value of a resistor while it is in a circuit. You have to pull it out. Also, with all the VLSI technology these days you could easily kill your card by checking resistance while the resistor is in the circuit. When you measure the resistance with a volt/ohm meter you are shoving current thru the circuit in an attempt to measure the amount of "resistance" to current flow. It's particularly amusing when people take a multimeter in "buzzer" mode to check continuity on their X800 Pro to XT mods. Holy $hit!Quote:
Originally posted by Kasp2k
One thing, I checked the ohm's now.., it was reading 383ohm, is this std on the X800PRO @ the R1597 chip..
Unless you have money to burn I suggest you RMA your card and leave it alone if ATI is nice enough to fix it for you. Perhaps a transistor radio would be a more economically sound choice as a platform to learn basic electronic principles on?;)
Is it possible to use the x800XT Bios for this mod? I've seen that all mods are made with the x800XT PE Bios, but the PE Core is higher, as the XT. Specially the Memory frequency is with the PE Bios higher. 1140 Mhz without better cooling is not possible for a long time
I have seen some successfully mods without any flash. so i think you dont need to flash a bios. only make the hardmod and then see, if 12 or 16 pipes are showing. If you have 16 Pipes, you can flash it to XT and then the card is in systems tray showing as real XT (that is only possible if 16 pipes), but it is not necessary to do flash to have 16 pipes or not.
And an XT Bios, i havend found anywhere to download, only XT PE. You??
To the Memory Frequencys: My Card works up to 600Mhz, so your card can run without problems 573Mhz i think.
of course u dont need to flash to have 16pipes, flash is only needed to have xt clocks ;)
i could not get passed 1.46v on the core en 2.07v on the mem , i t just wont get higher stupid x800pro from powercolor
clock are 620core en 613mhz mem
colled with chiller water 10c
All XT's are Platinums. There is no such thing as a "regular XT".
I just got my X800 pro power color w/ vivo. Checked with ati tool and it said 12 piplines. Flash the bios and now it says 16pipline. The card also has 1.6ns mem.
Benches please.:DQuote:
Originally posted by Shroomalistic
I just got my X800 pro power color w/ vivo. Checked with ati tool and it said 12 piplines. Flash the bios and now it says 16pipline. The card also has 1.6ns mem.
got 11583 in 3dmark03 so far. stock card xt clocks. Ill push it a little now to see how far it will got. Im still running stock cooler too.
lool so powercolors x800 vivo cards are xts... or at least some of 'em :)
so far I got 540/580 clocks, just before I went to bed. Scored 24.9k 3dmark2001 and 12k 3dmark03
Got a compare?Quote:
Originally posted by Shroomalistic
got 11583 in 3dmark03 so far. stock card xt clocks. Ill push it a little now to see how far it will got. Im still running stock cooler too.
i have een x800pro by powercolor to clocks, 625core/620mem sofarQuote:
Originally posted by Shroomalistic
I just got my X800 pro power color w/ vivo. Checked with ati tool and it said 12 piplines. Flash the bios and now it says 16pipline. The card also has 1.6ns mem.
with wich bios did you flashed it ?
http://discuss.futuremark.com/forum/...=5&o=0&fpart=1
the one from that thread
Good job!