I don't have it. Try to back it up from your other BIOS chip onto USB stick with EZ flash if you can.
-Raja
I don't have it. Try to back it up from your other BIOS chip onto USB stick with EZ flash if you can.
-Raja
Thank you boss. Have been looking for this BIOS.Quote:
Originally Posted by LardArse
Why wont my Z87M-plus or my Gene post with generic HCH9 samsung rams? Mem-ok doesnt help either ....
Also, why was my 4670K much faster at 1mb pi than my 4770K with same clocks, same ram ....
:(
Not enough info there to answer why. You'll have to give a breakdown of what you tried and how the system was setup etc.
Thanks master sham
What would you like to know? Both systems were tested with Team 2400c9 and 2666c10 rams, then bios reset to default, rams swapped to HCH9 and no POST, the Gene gave code 55.Quote:
Originally Posted by Raja@ASUS
:(
The comment on super pi you should be able to debug yourself. Check memory timings and core frequency and any other related performance parameter is lined up during the run. Your posts are very brief in nature my friend - nobody can piece together stuff so easily from a distance. Even when you are frustrated, you need to lay out a post and describe everything you did and how. This kind of stuff is down to you being able to match up the parameters so I'm going to leave it up to you.
As for the Gene not BOOTing those DIMMs, which slots are you using? Changing DIMMs can be finnicky, if it was a swap out the IMC seems to hold on to training from previous DIMMs at times unless one is very careful in how the system is defaulted (have seen it happen). Old Samsung is not a good bet for clocking on Haswell thus far. BBSE/PSC still rule, while newer Hynix and co are good too.
Slots 1&3 are better than 2&4 on these boards as well.
any new bios for the Maximus VI Gene
Retail chip @ 195 BLCK on Corsair H90, all with just four clicks in BIOS:
http://valid.canardpc.com/2840147
This board rocks.
http://img.techpowerup.org/130622/DSCF9404.jpg
Latest betas thanks to Shammy:Quote:
Originally Posted by Phaseshift
latest M6E bios combined with latest OC panel F/W - If LN2 Mode EN, oc panel automatically turns on and switches to extreme mode
http://www.mediafire.com/download/l6...ASUS-0021a.rar
http://www.mediafire.com/?d46772ddk5lwot2
Latest M6G BIOS
http://www.mediafire.com/?2l6a1u93sa0rx0x
Latest M6Hero BIOS
http://www.mediafire.com/?6or22j02ifmuzx3
for the life of me i cant get 1t fully stable without increasing the vdimm
setting 34k on read/write at 2200 7-10-7-27 2T 1.625v PSC fully stable at 4.4ghz uncore.Tested with prime for 4 hours. Got the uncore up.
http://img13.imageshack.us/img13/654/e7r3.png
Raja,
I would like to ask you a simple question. I want to buy a new motherboard. I was between the two models. Hero and Sabertooth. These motherboards are significant differences found between the area of overclocking?
I have 4770K :)
Thanks:)
Hero might be a bit better on the memory side. CPU is limiting factor most of the time, though.
Few images from quick OC session. Lol, I had not much time to study Haswell (busy time few weeks), so the results are not the best...August will be great month for home OC....
At the beginning was only dark...
http://i.imgur.com/WORwjq7.jpg
People need here a bit LN2 in terms and dark was gone
http://i.imgur.com/hEhl1tx.jpg
http://i.imgur.com/N1WLF7e.jpg
http://i.imgur.com/49A4O9H.jpg
http://i.imgur.com/O5ni9vT.jpg
http://i.imgur.com/VJzJBP6.jpg
I like AMD, ROG and Intel is not bad too :)
http://i.imgur.com/MsLBRt0.jpg
buttons under cold :)
http://i.imgur.com/HjNhYDa.jpg
temps:
http://i.imgur.com/wtQitef.jpg
http://i.imgur.com/eUmmtqc.jpg
after OC session :)
http://i.imgur.com/VN9EgTd.jpg
OC men and girl, whoaaaaaa :D
http://i.imgur.com/29Sinjk.jpg
setting for 2200 C7 with uncore 4.4ghz. So far this looks like 24/7
http://img580.imageshack.us/img580/2374/og8.png
btw still looking at how to make x-talk cancellation voltage beneficial on stability....
any guides on what ranges or is it more a cpu multiplier thingy.
Check Shammy's guide for that. He gives you the usage ideas.
Raja - that is a great guide but so much to take in, when chasing 24/7 overclocks which voltages can be used to assist stability and allow lowering of vcore?
My current cpu isnt anywhere near as good as every second guy seems to get here but its the best of the three I have owned. It primes 4500 at 1.30v under full water cooling and has been delidded. Mobo is a Maximus VI Gene and I using 2666c11 Trident-X rams.
:D
Keeping the cache and DRAM ratio low is one way. Other than that, you aren't going to get a lot to trade against Vcore.
yup understood sir, always seems to go back to the drawing board with 2133 C7.Quote:
Originally Posted by Raja@ASUS
xtalk up to 1.1v, vccin down to 1.75v so far so good with prime.
going back to test again with my 2200 and hopefully with this will give me some insight in getting closer to 2266C7 stable and then to 2333 C8
btw why mem tweakit gives higher score for lower tREF. shouldnt it be the other way around??
Yeah that should be reversed. It's just a "fun" thing that score, so take it with a grain of salt.
Z87 Deluxe review is live. If anyone is interested in having a look here it is: http://www.hardwarecanucks.com/forum...rd-review.html
Thanks Zac. I know you put a lot of work into that!