No more than 3.7Vmem...........I'll pelt them and I'll try higher........ ;)Quote:
Originally posted by zabomb4163
so how many volts have you pumped into your ram so far?
No more than 3.7Vmem...........I'll pelt them and I'll try higher........ ;)Quote:
Originally posted by zabomb4163
so how many volts have you pumped into your ram so far?
You're welcome....... :D :toast:Quote:
Originally posted by enzoR
:hehe:
thanks m8
:toast:
nah, try LN2 :DQuote:
Originally posted by hipro5
No more than 3.7Vmem...........I'll pelt them and I'll try higher........ ;)
Ama eisai ellinas kaneis kales douleies :)
Does this VTT mod sound ok, to you?
1. Cut trace from back of the board
2. Leave MC50 cap in its place, and solder wire from center leg of vr to its upper side (closer to Winbond chip).
3. Solder wire from vr to VTT mosfet lower (source) leg.
4. Solder last free leg of vr to ground.
Resistance (of vr) between MC50 and VTT mosfet should be first 0ohms, right?
Thanks :D
Yes it's OK......BUT you have to solder the wire of the Mos-Fet on the Drain of the one and Source of the other(closer to rams) where we measure the VTT......Quote:
Originally posted by The Stilt
Does this VTT mod sound ok, to you?
1. Cut trace from back of the board
2. Leave MC50 cap in its place, and solder wire from center leg of vr to its upper side (closer to Winbond chip).
3. Solder wire from vr to VTT mosfet lower (source) leg.
4. Solder last free leg of vr to ground.
Resistance (of vr) between MC50 and VTT mosfet should be first 0ohms, right?
Thanks :D
Thanks my friend.... :toast:Quote:
Originally posted by gr4vity
Ama eisai ellinas kaneis kales douleies :)
hipro did you get the digicam?
Yes....Today afternoon(in a few hours)....... ;)Quote:
Originally posted by enzoR
hipro did you get the digicam?
]
:slobber: It makes me happy :D :toast:
Can you clear it little bit?Quote:
Originally posted by hipro5
Yes it's OK......BUT you have to solder the wire of the Mos-Fet on the Drain of the one and Source of the other(closer to rams) where we measure the VTT......
So one wire goes to MC50 side, one to mosfet (Q6) leg, where the VTT is measured, and the last one to?
Thanks again :)
If you don't solder a resistor(as you say) then it's going to ground......Quote:
Originally posted by The Stilt
Can you clear it little bit?
So one wire goes to MC50 side, one to mosfet (Q6) leg, where the VTT is measured, and the last one to?
Thanks again :)
Thanks for your efforts m8 :DQuote:
Originally posted by hipro5
If you don't solder a resistor(as you say) then it's going to ground......
VTT, VDDR and Vchip mods work like charm.
Tomorrow Im trying to get in serious business ;)
hipro, ive done all 5 of your mods. 4 work like a charm xcept the vtt mod.(i did the second vtt mod cutting trace on back of board/with vr pot) i found that it just burns up any pot used(cause it needs almost a dead short to work). the only way i can get it to track1/2 vtt is to use a .25 ohm 3watt resistor to grd instead of the vr pot.. can u help??? thnx
update well, seems i burned up or severly weakened the power mosfets to the vtt . funny right after i posted this ,the rig just shut
down and on inspection the far right hand power vtt mosfet was burned. tho the rigg runs i can only get 1 volt thru to feed my vtt.Well daddy hipro, any suggestions??? or am i sunk.... thnx flapper
use malves method for the VTT mod
Mods seemed to help my IC7-Max @ IC7-G Downgrade littlebit ;)
Thou I have to make Vnorth mod, because it give only 1.22V by default, when using prescotts :D
http://mbnet.fi/elixir/3.2E/Unbuffered-260FSB.PNG
Well done The Stilt.......... :toast:
Try to up the Vagp at 1.95Volts when playing with 1:1 CPU:RAM........ ;)
You might have soldered the trimmer to the Mos-Fet's side.......Check if you soldered them to the M64 side.......(of the 10 Ohms resistor).....Quote:
Originally posted by flapperhead
hipro, ive done all 5 of your mods. 4 work like a charm xcept the vtt mod.(i did the second vtt mod cutting trace on back of board/with vr pot) i found that it just burns up any pot used(cause it needs almost a dead short to work). the only way i can get it to track1/2 vtt is to use a .25 ohm 3watt resistor to grd instead of the vr pot.. can u help??? thnx
update well, seems i burned up or severly weakened the power mosfets to the vtt . funny right after i posted this ,the rig just shut
down and on inspection the far right hand power vtt mosfet was burned. tho the rigg runs i can only get 1 volt thru to feed my vtt.Well daddy hipro, any suggestions??? or am i sunk.... thnx flapper
hipro, to do the 5v mem mod which leg of the mosfets do i need to lift up and do i need to lift up both mosfet legs?
No......You have to lift up the leg of this Mos-Fet of the photo......The one which I've soldered the "fat" cable on.......Unsolder it with MUCH care not to break the Mos-Fet's case and feed it with 5Volts........ ;)Quote:
Originally posted by enzoR
hipro, to do the 5v mem mod which leg of the mosfets do i need to lift up and do i need to lift up both mosfet legs?
EDIT......After that you have to put heatsinks on the two output Ram's Mos-Fets(The big ones).....
Quote:
Originally posted by hipro5
You might have soldered the trimmer to the Mos-Fet's side.......Check if you soldered them to the M64 side.......(of the 10 Ohms resistor).....
soldered exactly as u diagarmmed.. is it worth it to change the mosfet out??
Which Mos-Fet's out?...Quote:
Originally posted by flapperhead
soldered exactly as u diagarmmed.. is it worth it to change the mosfet out??
Quote:
Originally posted by hipro5
Which Mos-Fet's out?...
the mosfet that burned, was the 2nd vtt mosfet in the corner next to the dimm slot
Yes if you have another one from another mobo you can do it..... ;)Quote:
Originally posted by flapperhead
the mosfet that burned, was the 2nd vtt mosfet in the corner next to the dimm slot
thankyou hipro i will try.. im pretty good at this cause i work in hi -tech(tho u are my master). i followed this mod EXACTLTY what do u think happened?? im at a loss.... without prints i find it difficult to trak what went wrong....