Thanks. Could have done without the music though. LOLQuote:
Originally Posted by therager
Although I see no need to use extra solder. I've been pretty fortunate with things like this in using what is already available. :shrug:
Printable View
Thanks. Could have done without the music though. LOLQuote:
Originally Posted by therager
Although I see no need to use extra solder. I've been pretty fortunate with things like this in using what is already available. :shrug:
Wonderful Tweazers my #$@!!!
Anyone know what the number is for that sucker from Radio Shack?
I'm skimming the post to see if anyone lists it. :mad:
Any change you know any more information about the dang little $#$$@$@Quote:
Originally Posted by The-Fox
http://search.digikey.com/scripts/Dk....dll?Selection
There are 990 different surface mount resistors that are 100OHM.
Damn why didn't I listen to myself and not use the freaking tweezers. :shakes:
You should add some Pb-containing solder (like on the video) to lower melting temperature of mb Pb-free solder. Otherwise resistor removal is almost impossible with regular soldering-iron.Quote:
Originally Posted by scgt1
Ok it seems the only key value for this use is the 100 ohm. I've got an old hard drive laying around. I'm not the greatest with a voltage meter. I know red goes on the ohm plug and black to com. The settings I have are 20M, 2M, 200K, 20K, 2K->+, 200. Ideally I would think it needs to be on the 200. Although I've tried measuring others on the mobo around the mod area and I'm getting different values on many while some are measuring the same. So does anyone know what other resistors on the bloodrage are 100 ohm and their location so I can pull the same reading to see what it needs to say to test the hard drive resistors?
Another thing I don't know if my meter works properly which could cause a big problem with this. If I have it hooked up as above and set it on 200 I'm left with a 1 on the left of the screen then a small 200 off to the right at the bottom with a decimal right above it. Then if I touch the leads I'm left with 00.0 on the screen for a reading. Which ideally it should be 0 I think, but the decimal is off by one. Meaning I don't think there should be a decimal there.
hmmm depends on the iron, isnt the melting point of ROHS solder only ~10C higher?Quote:
Originally Posted by therager
I used some $20 Radioshack special and have done xbox work and inverter board fuses on a viewsonic monitor. I had no problem just heating up the solder and using the pick to remove the resistor.Quote:
Originally Posted by saaya
Just those damn tweezers that have so far screwed me out of a bloodrage. :mad:
Depends on the solder type mainly, but the typical difference is about 50-60*C :):Quote:
Originally Posted by saaya
http://www.empf.org/empfasis/jan05/lfaudit.htm
http://www.empf.org/empfasis/jan05/i...udittable1.gif
Also if someone uses uncontrollable soldering-iron, the only way to lower melting temperature is to add Pb-containing solder :).Quote:
Hand soldering processes
Even for hand soldering, the processing differences between tin lead and lead free must be considered. The solder tip must be adjusted to the higher temperatures required. For lead free solders, the EMPF found that the solder tip temperature needed to be set between 343°C / 650°F and 371°C / 700°F as opposed to 315°C / 599°F for tin lead solders. Temperatures higher than 398°C / 750°F were considered unnecessary for most hand soldering applications.
depends what you solder with :DQuote:
Originally Posted by therager
ive been using a 25W iron for a few mods heheheh :D
I've done the mod on my board today.
Was able to boot into windows with pci frequency set at 114mhz, didn't bother trying any higher because that's all i've ever needed for 250bclks on my other boards.