EP45-UD3P Benches 3D at 670mhz+ FSB

Printable View

Show 100 post(s) from this thread on one page

10-19-2008, 06:02 AM
Pt1t

Quote:

Originally Posted by PPInDaHouse

you mean 650x10 3D stable? that was nice, hope you can get a similar or better one :)

X9 stable

i tested in X9 before to test in X10 under ln2 :(
10-19-2008, 06:31 AM
massman

Quote:

Originally Posted by Pt1t

http://valid.x86-secret.com/show_oc.php?id=432489

it was the last test of my burned E8600 , VTT 1.55v ,vNB 1.6v. PL10

I guess the VTT caused your chip to die :eek:
10-19-2008, 07:00 AM
boblemagnifique

Quote:

Originally Posted by massman

I guess the VTT caused your chip to die :eek:

No it's a Bug Vcore (1.8v bios -> 2v real) , after in air (same with the clear mos) -> 1.8v Vcore -> E86 dead :(
10-19-2008, 07:16 AM
Oliver

sounds wicked, but 1.55VTT is ya like Pieter says
10-19-2008, 09:32 AM
Kain XS

I still haven´t had any problems using very high PLL and VTTs with Gigabyte Boards.
Mine can do 615 Max only for suicide shot.
600 is possible but not for 3DMark.
Stable for all kind of benching goes around 560 only.

Maybe Im missing something.
Memory BTW is good. I´ve got 700MHz with Team Group which I couldn´t with any mobo before.
10-19-2008, 09:34 AM
surrealX

Fantastic FSB. Nice job
10-19-2008, 09:37 AM
T_M

VTT had nothing to do with the failure of the CPU.
It was a plain and simple vcore bug that pumped waaaay too much volts into the chip while it wasnt cold.

1.55VTT is child's play compared to what i run
10-19-2008, 09:40 AM
Pt1t

Quote:

Originally Posted by T_M

VTT had nothing to do with the failure of the CPU.
It was a plain and simple vcore bug that pumped waaaay too much volts into the chip while it wasnt cold.

1.55VTT is child's play compared to what i run

sure ... this chip took 1.75 vtt on EP45Textreme, here it s different, it s only caused by high vcore en air.
10-19-2008, 01:47 PM
dinos22

VTT did not kill your chip
it was vcore
10-19-2008, 01:50 PM
dinos22

Quote:

Originally Posted by boblemagnifique

No it's a Bug Vcore (1.8v bios -> 2v real) , after in air (same with the clear mos) -> 1.8v Vcore -> E86 dead :(

same board or a different board

it's probably just a lemon board :shrug:
10-20-2008, 04:51 PM
[XC] gomeler

Been struggling with this board for the last hour or so. I can get 525FSB to post with my golden E8600 but anything above that is an instant crash. Can you guys doing 600FSB tell me the following?
CPU/MCH Skews?
FSB holes?(I think 400-433 is bugged, never boots for me)
MCH Latch used? 333MHz is proving to be far more stable than 400MHz
Performance Enhance used? Turbo(default) works better than Disabled or Extreme

I'm using 6x multi and the following volts on the QX9650 cooler. This CPU was doing 600+FSB with the EP45T-Extreme on air and the memory does DDR2-1240 CAS4 so I assume it must be the board.

vCore: 1.30v
vMCH: 1.50v
vDIMM: 2.10v
10-20-2008, 11:10 PM
Benny Lodewijk

Quote:

Originally Posted by [XC] gomeler

Been struggling with this board for the last hour or so. I can get 525FSB to post with my golden E8600 but anything above that is an instant crash. Can you guys doing 600FSB tell me the following?
CPU/MCH Skews?
FSB holes?(I think 400-433 is bugged, never boots for me)
MCH Latch used? 333MHz is proving to be far more stable than 400MHz
Performance Enhance used? Turbo(default) works better than Disabled or Extreme

I'm using 6x multi and the following volts on the QX9650 cooler. This CPU was doing 600+FSB with the EP45T-Extreme on air and the memory does DDR2-1240 CAS4 so I assume it must be the board.

vCore: 1.30v
vMCH: 1.50v
vDIMM: 2.10v

Just leave all auto in the BIOS. I can bench FSB 600 Mhz with ALL AUTO setting in BIOS.
10-21-2008, 12:10 AM
ezaleina

did anybody try Oc using e8400 E0 stepping?
10-21-2008, 12:18 AM
bigslappy

Mine went back for RMA to EGG .. could NOT hold any volts , clock, FSB with any consitensity , under clocked the Q9650 no matter what & yes I turn off all the CPU throttling settings , even ran everything on auto & still was the sh*t , swapped out 3 different types of RAM , 3 different vid cards , even swapped the PSU ... would not enter O/S at 400 FSB & when it did get into windows the clock kept changing every 60 seconds up/down NewEGG rma's gonna refund the mobo & i ordered another . I get it wed. OR thursday............
10-21-2008, 01:41 AM
taz-nz

Has anyone tried fitting Thermalright HR-09 Mosfet Coolers to this board yet ?

http://www.thermalright.com/new_a_pa...s/image004.jpg

If not can someone please measure the base plate width & length of the mosfet heatsink on the top edge of the board, and any clearance gap between the base of the heatsink and the chokes.

thanks
10-21-2008, 01:43 AM
Devious

Quote:

Originally Posted by bigslappy

Mine went back for RMA to EGG .. could NOT hold any volts , clock, FSB with any consitensity , under clocked the Q9650 no matter what & yes I turn off all the CPU throttling settings , even ran everything on auto & still was the sh*t , swapped out 3 different types of RAM , 3 different vid cards , even swapped the PSU ... would not enter O/S at 400 FSB & when it did get into windows the clock kept changing every 60 seconds up/down NewEGG rma's gonna refund the mobo & i ordered another . I get it wed. OR thursday............

Mine arrived today to try with my Q9650. Im thinking i might just send it back as no one except hicookie is having any luck with a quad.

Are there any package seals to break if i was to have a quick play?
10-21-2008, 02:25 AM
hicookie

Quote:

Originally Posted by bigslappy

Mine went back for RMA to EGG .. could NOT hold any volts , clock, FSB with any consitensity , under clocked the Q9650 no matter what & yes I turn off all the CPU throttling settings , even ran everything on auto & still was the sh*t , swapped out 3 different types of RAM , 3 different vid cards , even swapped the PSU ... would not enter O/S at 400 FSB & when it did get into windows the clock kept changing every 60 seconds up/down NewEGG rma's gonna refund the mobo & i ordered another . I get it wed. OR thursday............

how come even can't just 400MHz FSB?hmm...whats ur memory?
10-21-2008, 04:01 AM
systemviper

i got my QX6850 to 503fsb @ 1.39v 4Ghz, i got my 2nd Q9650 so i will pop that in today and see if i can get higher FSB.

CPUz
10-21-2008, 04:12 AM
cstkl1

isnt that 3dmark06 score kindda low..
could have sworn that i got higher with 790/1100 on a gainward GS 1gb 4870 at 4.264ghz..
10-21-2008, 04:27 AM
systemviper

Quote:

Originally Posted by cstkl1

isnt that 3dmark06 score kindda low..
could have sworn that i got higher with 790/1100 on a gainward GS 1gb 4870 at 4.264ghz..

Hi, u talking to me' :shrug:

If so 20k with a 3870x2 is sweet..... :up:
10-21-2008, 04:49 AM
cstkl1

oops sorry i meant to TS.
10-21-2008, 05:24 AM
[XC] Hicks121

I have mine running 460 x 9 on my e8400. Will have a x3330 here this week to test.
10-21-2008, 08:38 AM
[XC] gomeler

Quote:

Originally Posted by Benny Lodewijk

Just leave all auto in the BIOS. I can bench FSB 600 Mhz with ALL AUTO setting in BIOS.

All settings including voltages? I left everything on auto but the memory divider(it was trying to do DDR2-1800 :ROTF:) and I can still only do 525FSB.
10-21-2008, 08:57 AM
bigslappy

Quote:

Originally Posted by hicookie

how come even can't just 400MHz FSB?hmm...whats ur memory?

G.Skill super PI f2-8800cl5d-4gbpi = ddr21100 (tried 4 gb & then 8 gb of each) & g.Skill ddr2-1066 & ddr2-1000 both 2 gb a stix no change on the the board with any of them , ALL still acted the same on the mobo .. dod memory test on all they passed & all worked fine on my Rampage Formula mobo's ... moBo was just not acting right from the start
10-21-2008, 02:26 PM
Devious

Installed a UD3P tonight and at last ive managed to boot at 500FSB with my Q9650 which i couldnt get near with my Asus boards. (booted @ 515x6)

Ive left nearly everything on auto in the bios (which i read most people were doing) which imressed me but then ive just installed easytune and looking at that its raised some of voltages to scary levels:eek: which probably explains the 500FSB.

http://img205.imageshack.us/img205/8094/capturedf8.jpg

Its not stable at all, it will run prime small FFT for a few mins before BSOD but blend fails instantly.

Is this a cpu wall or some ram issue ? Im running 4GB OCZ flex 9200 ram.

Show 100 post(s) from this thread on one page

All times are GMT -8. The time now is 07:14 AM.

XtremeSystems