Only 2300MHz? Which stepping is that again?Quote:
Originally Posted by Dave_Sz
Printable View
Only 2300MHz? Which stepping is that again?Quote:
Originally Posted by Dave_Sz
ldbfe 0622EPMW
I have two and the other seems to be ok with 270x10 with 1.458v though.
I've got a LDBFE 0622WPMW sitting here waiting for a motherboard. Hope it does atleast 2.6GHz.Quote:
Originally Posted by Dave_Sz
Those manchesters are looking really good bang for buck after the price drops im very tempted to get one
Just ordered one here from Directron for $158 shipped.
just got a LDBHE 0601TPEW from newegg...so far im priming at 2.6GHz 1.35v
:banana::banana::banana::banana:, that's what I get for ordering from mwave. Newegg still has old stock chips so they're still selling those, the good clocking ones.
Hi guys .. i got a LDBFE 0614 WPMW Chip .. priming at 2800 with 1.51 Vcore.. but i have a doubt ..
The smartguardian temp read out is 50 on full load .. but the Core temp program showing 71 on core 1 and 65 on core 2 ... :confused:
is it save? pls help me :(
who knows. On my single core the the core temp thingy was 2-3 * lower tham mbm5. With my dual core chip, it's 10* higher than mbm5.
hmm core temp program shows my core temps at 66C and 58C at 1.47v while smartguardian shows my cpu temp at 44C. Think the IHS is making bad contact with my core?
Hi Droz. are you using water or air cool?Quote:
Originally Posted by Drozdov
air cooling, using a big typhoon..
anyways its too late, I took off the IHS, but the CPU is dead..
there is no physical damage, my system won't turn on at all.
I guess it was running too hot...
make sure none of the contacts on the transistors or caps were cut. The leads are so small it's easy to miss it...
finally have a 06 on my own, but personally I liked my 05 more.
06 now has CB and is sometimes a bit strange during first boot (freeze or reboot, needs 2-3 tried)
My 05 was rockstable under subzero but didn't scaled with cold that good.
Think 3800+ are very luck-dependent whether you get a good one or not :(
wish i had a digital camera with me so i can take a pic of it. It looks like none of them are damaged.Quote:
Originally Posted by Dave_Sz
just had a better look at it...the core is cracked..
that blows dude.
on a lighter note, so far I got mine up to 245x10 with stock volts and it's around 105* outside...
damn, this is the best manchester stepping !!!Quote:
Originally Posted by Drozdov
They run REALLY hot tho.
I had mine @ 2.8 stock vcore, 2.85 1.34v, 2.9 1.39v, 2.95 1.45v.
yeah they do run hot, i took off the IHS and found out why ;)Quote:
Originally Posted by Supertim0r
too bad my core got cracked when I installed my big typhoon, here is the last stable screenshot i got off of my LDBHE 0601.
Anymore news on the overclocking on this chip or stablility at those settings? I've got a chance to get one of them so please let me know. :)Quote:
Originally Posted by menlatin
sry, bit of a noob here -
Hmm, so all x2 3800+ 06 Manchesters are good clockers? There was a LDBFE 0623 on eBay the other day, but I couldn't find anyone with this stepping, and as it was £20 than shop prices i thought i better leave it.
I'm in the UK, so if I bought a retail x2 3800+ from a shop would it almost certainly be an 06 manchester?
why??? bad contact???Quote:
Originally Posted by Drozdov
They run hotter than single cores., some Chips may have bad contact. I removed my IHS of a 3800X2 and had a good few oC droped of the temps.Quote:
Originally Posted by Dave_Sz
yes but he didn't say they run hotter than single cores, he said they run HOT and he saw why...
http://www.halfempty.co.uk/robin/eba...2/IMG_4963.JPG
Every stepping that pops up on eBay never seems to be common. ..
How well do you reckon the above cpu would overclock?
yep, poor contact between IHS and coreQuote:
Originally Posted by Dave_Sz
LDBFE 0610UPAW
2.65Ghz with just under 1.5v. Made it to 2.5 with stock volts but anything more than that kept failing unless I packed on the volts. Went up to 1.53v trying for 2.7Ghz but it was getting to be a little too much for my Al XP90. Idle at 33C and load at 48C now.
http://valid.x86-secret.com/show_oc?id=109422
LDBFE 0622EPMW
Voltage is 1.5v. It did dual 32m at 2.8 same voltage, it may do 2.7Ghz at ~1.475 24/7 full load, but didn't test that yet. Problably gonna have to bump the speed/volts down when the heat returns, at 27c ambient CoreTemp said 52/56c.
well I can tell you that LDBFE 0623 XPMW is junk. 2.5GHz is stable at 1.44v, but im priming 2.6GHz @ 1.5v :rolleyes:
I'm running a 0606 EPMW. After removing and replacing the IHS, I'm at 2.7GHz at 1.375v Prime stable for 7 hours so far. Core Temp is showing 50/51 on load. Hoping to get to 2.8 but my RAM isn't cooperating.
ram not co-operating??? dividers...
you're letting your ram affect your CPU OC, you're OCing wrong...
Whenever I don't run the RAM 1:1, my overclock goes unstable. Just got this board (CFX3200) so I haven't had a chance to really get into all the settings.Quote:
Originally Posted by Dave_Sz
Just recieved the exact same stepping from the "Egg".Quote:
Originally Posted by Espion
It might be a week or so before I can install'er but will keep you posted.
:toast:
Just recieved the exact same stepping from the "Egg".Quote:
Originally Posted by Espion
It might be a week or so before I can install'er but will keep you posted.
:toast:
I have an X2 3800+ running 2.8GHz @ 1.344v right now. I'll post a screeny after it primes for about an hour ;)
Nice!!!Quote:
Originally Posted by shoman24v
Give us your stepping please.
:toast:
LCBIE 0618 EPMW 2.8GHz @ 1.344v
Imagine if I gave it some voltage lol... This is on air.
http://img146.imageshack.us/img146/7...board01kz9.jpg
Nice shoman!Quote:
Originally Posted by shoman24v
Hopfully my 3800 will be close.
:stick:
ok, change the 4 major ram to the timings the ram is advertised for, all others change to AUTO. If that doesn't work, maybe a poor MEM controller?Quote:
Originally Posted by Dark79
I forgot shoman, you STOLE your chip!Quote:
Originally Posted by shoman24v
:toast:
Just kidding, seems to be getting better and better as you go, wish I could stumble upon such a chip.
:up:
LDBFE 0620VPMW
http://img223.imageshack.us/img223/9...3389ci8.th.jpg
2.78 Ghz
http://img136.imageshack.us/img136/8...20amcv3.th.jpg
Still pushing - 2.8 (280 x 10) is stable though too. Will update as I push up.
another LCBIE 0618EPMW
2800mhz@stock
http://img169.imageshack.us/img169/8...3hrswt6.th.jpg
more tinkering...
SP32M@ 3000mhz:
http://img20.imageshack.us/img20/895...p32mxy9.th.jpg
http://valid.x86-secret.com/show_oc?id=110261
SP1M@3100mhz:
http://img191.imageshack.us/img191/5...sp1mcp7.th.jpg
http://valid.x86-secret.com/show_oc?id=110263
God damn those are some nice chips...
I'm guessing that all of these x2 3800+ are of the S939 bunch?
I'm a bit disappointed in my 0607UPMW "N", I need phase. 2.6ghz max @ 45c 1.425 Anyway with the AMD price cuts and they seem to be putting Toledo cores in allot of 0618’s. I could pick up three of em and sells the rest that don't OC. I say a new 2006 x2 3800 TOLEDO thread is needed. They seem to be a whole nother beast.
haha just received another LDBHE 0601 TPMW from newegg today, this time i won't take off the IHS and risk having another dead LDBHE 0601
you had a TPEW IIRC ?Quote:
Originally Posted by Drozdov
yeah TPEW the first timeQuote:
Originally Posted by Supertim0r
Which are the codes in the steppings for the Toledo chips? I thought all x2 3800+ chips were manchesters. And where is everyone getting these toledo cores?Quote:
Originally Posted by hawkeyefan
Quote:
Originally Posted by hawkeyefan
How far is this chip actually prime stable though?
Any know what Newegg is shipping out? Have one coming tomorrow - already have a 620VPMW from Directron that is prime stable up to about 2.79 Ghz (1.47v) - the best OC'r will stay in mine, other into the wifes box.
Last week I got a LDBFE 0621XPMW from Newegg. So far 230x10 at stock volts. I want to put in my test hdd before I really start pushing it.
I would like to be able to prime stable at 2.8+ Ghz.Quote:
Originally Posted by Darkboss
I get that at stock volts but it primes at about 54c. Adding voltage doesnt affect it that much, I get about 2.9GHz at 1.4v in the bios. I think it needs better cooling.Quote:
Originally Posted by dnottis
which warehouse is it shipping from? both of my LDBHE 0601 came from the tennessee warehouse from newegg.Quote:
Originally Posted by dnottis
NJ WarehouseQuote:
Originally Posted by Drozdov
7B Brick Plant Rd.
South River,NJ 08882
service@newegg.com
Quote:
Originally Posted by shoman24v
I'm using a dual radiator with Apogee, my load temps on the CPU sensor are 38. Internal temps for core 0 is 41 and core 1 is about 50 c.
LCBIE 0618EPMWQuote:
Originally Posted by Darkboss
batch 0686
got it at MicroCenter in Minnesota for $179.99 USD, one left with batch# ~1200 iirc.
don't know yet really. Big week for Rosetta, right now it's been happily crunching 24+hours@ 2950mhz 1.513v.Quote:
Originally Posted by dnottis
ran dual prime small FFTs for 3.5hrs before getting impatient. 2800mhz@ stock
http://img169.imageshack.us/img169/8...3hrswt6.th.jpg
also ran dual prime Custom test for ~2.5hrs (1024-4096k fft lengths, 400MB/core, priority 9) @ current speed, again gave up out of impatience. Popping the ihs next week and then going to sort this out some more. This has all been ihs intact, stock TTBigTyphoon, closed case with a weak PSU and ambient of ~75F.
just fwiw, here is my only run of 3DMark06 so far. 3070mhz @ 1.568v
http://img462.imageshack.us/img462/8...3070qn1.th.jpg
mm not sure then, i think the TN warehouse still have the old chips. I rarely get stuff from the TN warehouse when i order something on newegg, its always shipped from CA or NJ warehouseQuote:
Originally Posted by dnottis
Man I am going to have to try and get one of these chips, dirctron is right down the street from me. I think I will go take a look and see if they have any.
I just recieved one from Newegg NJ.
LCBIE 0618 EPMW
From all the others that have this stepping, looks like 2.8 close to stock volts should be possible - and those were on air. I'm using water so I'm hoping to get at least 2.8 Prime stable if not more.
nice one, good thing you didnt get the 062x steppings, those are horrid.
Got the new chip in, it's priming 3.0 Ghz @ 1.50v.
http://www.3dxtreme.net/other/CPUS/3...W/IMG_3537.jpg
excellent chip, thats under water cooling right?
Quote:
Originally Posted by dnottis
looks to be almost a given:fact: ;)
nearly 2 days@ full load Rosetta now, 0 errors 2950mhz 1.513v. Appears that 3ghz prime stable on air below 1.6v is very likely, even on air:banana: :banana:
Quote:
Originally Posted by Drozdov
Yea, MCP350 pump, Black Ice GT 240 radiator w/ 2x75cfm 120s, Swiftech Apogee Cpu block and maze4 on X1900XTX (690/800). All 3/8"ID tubing.
Load varies - using Everest overall CPU temp is about 42 load from the sensor. core 0 says 40c, core 1 says 47c. This chip shows the two cores about 7 deg apart. My 620 VPMW showed the cores being about 12 deg apart.
Quote:
Originally Posted by dnottis
fwiw, my Core0 is much stronger than core1. tried priming 3100mhz briefly. in a few seconds, core1 crashed, core0 kept on going...
Today from New Egg in Tenn.
LDBFE0620VPMW
I won't install this until this weekend.
Previous X2's came from;
NJ
LDBFE0610UPMW[10x260]
TN
LDBFE0610SPAW[10x250]
These are all within the last 3 weeks. I use these for crunchers[24/7 on air] so I don't reall twist them up much:(
Quote:
Originally Posted by mike047
My other chip is the same, 620 VPMW - max prime stable is about 2780 @ 1.472v.
For me that is good, I won't go over 2600 on my crunchers:DQuote:
Originally Posted by dnottis
Hi, I have got an offer of buying a x2 3800 with the stepping "LDBFE 0623WPMW" or "LDBFE 0622EPMW" are any of these two good overclockers??, and then which one should I go for?
// David
Wow - I feel like Wind With Me with the incredible overclocking chip now LOL
Feast yer eyes boys - this was with the voltages set to auto in the BIOS. My 620VPMW is Manchester, this 618EPMW is Toledo.
http://img212.imageshack.us/img212/2...20amcy8.th.jpg
http://www.3dxtreme.net/other/CPUS/3...W/IMG_3537.jpg
Is this the default Vcore?
Quote:
Originally Posted by Driver
Haha, yea. It's priming 2870 right now, same voltage.
:banana:
looks like LCBIE 0618 are the best
I got a LDBFE 0625APAW in from the Egg yesterday (Shipped from NJ warehouse) and it sucks. Needs 1.55v for 2.7GHz :slap: I never get lucky when I buy online, NEVER! :fact:
I had to bump to 1.32v (1.35v bios) to start priming 2.9 ghz.
I worked on one for a buddy that took 1.4v to do 2.4 GHz. Max volts for his mobo too lol.
LCBIE 0621, 0625, 0626 are also very good, some even better.Quote:
Originally Posted by Drozdov
Here's my newest, 0626 GPMW.
http://users.skynet.be/MetalHead/062...94_3100mhz.jpg
Holy hell Jupiler, thats sweet!!
I thought mine was doing good at 2870 1.29v!!
Either way these Toledo cores rock! I'm priming 2.9 Ghz now at 1.32v
Yeah,
I've been seeing good results from the weeks 0621VPMW, 0625VPMW and 0626GPMW. Most of them do 2.8Ghz with low volts.
I have another 0626GPMW, which does 2.9Ghz, at 1.37V stable.
But they do get hot though, adequate cooling is a must.
Hi .. are you refering to the manchester or Toledo chip?Quote:
Originally Posted by Jupiler
Those are all Toledo's I was referring too.
Tray versions.
Mine was Toledo but Retail box.
wow u guys are rockin with those chips, I am going to try and pick one up next weekend over at directron I would love to hit 3Ghz with it.
I do see 3Ghz being possible with mine, however prime fails after about an hour at 1.50v and temps begin to get toasty (~44) even on water. I'm not sure for 24/7 if it will be worth it since I can run 2870 at 1.29v (and 2.9 @ 1.35v) and have a load temp in the mid 30's.Quote:
Originally Posted by mar-one
LOL everyone and their mother are getting great clocking Toledo core 3800s but I still manage to get a horrible clocking 0625 Manchester. I'll take this as a sign that it's time to hang up the ol AMD boots for a while if you know what I mean. ;)
Maybe, but my Mom can't overclock for :banana::banana::banana::banana: :p:Quote:
Originally Posted by TheMeatFrog
yeah Im pretty dissapointed...I just bought a 3800X2 Manchester.
Its 0623 XPMW not sure of the 5 letters tho.
It wont go over 2.4-2.45ghz stable no matter what voltage I put it at.
I know it aint my board or anything else holding me back.
Also this is at 1.47v Ive tried 1.52v and that only gets me like 20mhz more.
Im extremely dissatisfied.
default voltage it wont do anything ... Im guessing over 2.3ghz cuz i know default crashes 2.4ghz
You are dropping HT mult to say x3? What mobo is it?Quote:
Originally Posted by GenTarkin
yeah my HTT is dropped to 3x and I know this mobo is capable of 295mhz HTT as per my last processor was a 3000+ in there and it was at 2.65ghz no problem.Quote:
Originally Posted by dnottis
Its Tforce6100-939 BIOSTAR board.
Do dual cores have an extremely ineffecient memory controller or something? cuz Im only getting like 5783MB/sec now vs before on my 3000+ with the same memory settings as now I was getting 6500MB/sec or so... my effeciency went from like 89% to 73%....same exact memory settings!
Would you call this stable? I would. :D
http://users.skynet.be/MetalHead/062...100stable1.jpg
http://users.skynet.be/MetalHead/062...3100stable.jpg
Yeah i think so lucky man
OMG .. tray version .. no wonder i can't find the batch in the retail box ...:mad:Quote:
Originally Posted by Jupiler
http://i12.photobucket.com/albums/a2...Myx23800-2.jpg
http://i12.photobucket.com/albums/a2...sSuperPi-2.jpg
Nothing special for this chip, but pretty good for me and the average x2.
This is a sub 31s superpi time with value GEIL DDr400 RAM, stock volts for RAM and CPU and what could effectively be called stock cooling, (actually Scythe Ninja but its not quite doing its job, 1m superPi brought the cpu up to about 43-47C with cold 18C room temperature.)
More to come hopefully :)
Here is my best low volts so far.
618 EPMW
http://www.3dxtreme.net/other/CPUS/3...2850-1.29v.jpg
Im wondering did I get an Energy Effecient chip, cuz the TDP rating is like 55Watts and the TcaseMax rating is 59C
the tcase explains why it sucks so much imo, I havent seen a rating that low on a X2 yet =(
same hereQuote:
Originally Posted by dnottis
I needed a voltage bump for 2.90 Ghz.
http://www.3dxtreme.net/other/CPUS/3...900-1.344v.jpg
nice chip! that with or without the IHS?Quote:
Originally Posted by dnottis
damn nice one dnottis, LCBIE are awesome chips.
here is my LDBHE 0601 under a Big Typhoon at stock volts :)