Live MB OC Report :: ASUS Rampage Extreme

Printable View

Show 100 post(s) from this thread on one page

12-13-2008, 11:32 AM
quattro_

after flashing to 0901 bios i cant load my OC settings ??? i flashed from 0501, now it always say my settings failed what am i doing wrong ?

these are my settings:

FSB Frequency: 450
CPU Ratio Setting: 09.0
CPU Clock Skew: Auto
NB Clock Skew: Auto
FSB Strap to North Bridge: Auto
PCIE Frequency: 100
DRAM Frequency: 1801Mhz
DRAM Command Rate: 1N
DRAM Timing Control: Manual
CAS# Latency: 8
RAS# to CAS# Delay: 8
RAS# Pre Time: 8
RAS# ACT Time: 20

CPU Voltage: 1.3500
Load-Line Calibration: Disabled
CPU PLL Voltage: 1.51106
FSB Termination Voltage: 1.10016
CPU GTLVerf (0): +70mV
CPU GTLVerf (1): +70mV
CPU GTLVerf (2): +70mV
CPU GTLVerf (3): +70mV
NB GTLVerf: +60mV
North Bridge Voltage: 1.51097
DRAM Voltage: 1.86881
NB DDRVref: Auto
DDR3 ChannelA Vref: Auto
DDR3 ChannelB Vref: Auto
South Bridge 1.5 Voltage: 1.51106
South Bridge 1.05 Voltage: 1.06039
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
12-13-2008, 12:44 PM
cheapseats

rob2k, I found your combination of 400 strap and CT Auto gives some very nice results at 475FSB/1:2 :)

With CT AUTO, the 400 strap is a lot faster than it was....

I did some more Everest tests with 475x9/1:2/CL7. These are the best and worst results I got across the basic strap/CT/tRD combinations at that FSB.

All tests : 475x9 / 1:2 / CL7

266 strap / CT AUTO / AIBOOSTER AUTO (tRD7)

http://i447.photobucket.com/albums/q...PLA_CS_EV1.jpg

333 strap / CT AUTO / AIBOOSTER AUTO (tRD6)

http://i447.photobucket.com/albums/q...PLA_CS_EV1.jpg

400 strap / CT AUTO / AIBOOSTER AUTO (tRD6)

http://i447.photobucket.com/albums/q...PLA_CS_EV1.jpg

---------------------------------------------------
with Manual tRD

333 strap / CT AUTO / tRD 6

http://i447.photobucket.com/albums/q...PL6_CS_EV1.jpg

333 strap / CT Strong / tRD 6

http://i447.photobucket.com/albums/q...PL6_CS_EV1.jpg

400 strap / CT AUTO / tRD 6

http://i447.photobucket.com/albums/q...PL6_CS_EV1.jpg

400 strap / CT Strong / tRD 6

http://i447.photobucket.com/albums/q...PL6_CS_EV1.jpg
12-13-2008, 12:52 PM
Ozzfest05

@ cheapseats go 500 FSB and 2000mhz memory and see what timings you can achieve also I would like to see a better cpu frequency 4.5 or so with the 2000 mhz
12-13-2008, 05:21 PM
GLENBOY

congrats toyten good results all round, managed a 635 fsb , 600 is no prob but once i went over 615 had to up the northbridge volts to over 1.7, only problem i still have is running a high memory speed at a high fsb (over 600) no problems round 500fsb or less, any tips , i found highering the tref and manually setting performance level helped

http://www.gbwatches.com/pics/635fsb.jpg
12-13-2008, 11:35 PM
quattro_

Quote:

Originally Posted by quattro_

after flashing to 0901 bios i cant load my OC settings ??? i flashed from 0501, now it always say my settings failed what am i doing wrong ?

these are my settings:

FSB Frequency: 450
CPU Ratio Setting: 09.0
CPU Clock Skew: Auto
NB Clock Skew: Auto
FSB Strap to North Bridge: Auto
PCIE Frequency: 100
DRAM Frequency: 1801Mhz
DRAM Command Rate: 1N
DRAM Timing Control: Manual
CAS# Latency: 8
RAS# to CAS# Delay: 8
RAS# Pre Time: 8
RAS# ACT Time: 20

CPU Voltage: 1.3500
Load-Line Calibration: Disabled
CPU PLL Voltage: 1.51106
FSB Termination Voltage: 1.10016
CPU GTLVerf (0): +70mV
CPU GTLVerf (1): +70mV
CPU GTLVerf (2): +70mV
CPU GTLVerf (3): +70mV
NB GTLVerf: +60mV
North Bridge Voltage: 1.51097
DRAM Voltage: 1.86881
NB DDRVref: Auto
DDR3 ChannelA Vref: Auto
DDR3 ChannelB Vref: Auto
South Bridge 1.5 Voltage: 1.51106
South Bridge 1.05 Voltage: 1.06039
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled

anyone??
12-14-2008, 12:55 AM
ToyTen

Hi, quattro,

Do you use a OC Profile for the eboot after flashing ? I had a similar issue willing to reboot on a Profile made under previous BIOSes. Tuning all parameters manually was the solution in my case.
In deed, the computer always rebooted everything by default, quiet annoying when one knows it was perfectly working right before the flashing. Hope I did help you
12-14-2008, 04:13 AM
quattro_

thanks for the reply ToyTen,
what is eboot??
ill try to input the settings manually and report back .
12-14-2008, 04:18 AM
ToyTen

Quote:

Originally Posted by quattro_

thanks for the reply ToyTen,
what is eboot??
ill try to input the settings manually and report back .

it's a kind of virtual boot unno :D

my bad, reboot was the word ;)
12-14-2008, 10:53 AM
quattro_

loool, it worked :) thank ToyTen
12-14-2008, 11:04 AM
ToyTen

Quote:

Originally Posted by quattro_

loool, it worked :) thank ToyTen

your welcome :)

It just happened again, coming back from 1001 to test more deeply the 0401 for Super Pi 32M on a C2D E8600. Glad I could help.
12-14-2008, 11:08 AM
Think

Anyone having corruption errors utilizing onboard Raid with 0 striping?
12-14-2008, 07:03 PM
aln688

Three questions:

(1) What are these BIOS's that a user named "Kensek" is making, what is supposed to be special about them? Obviously Asus never released a 1001 BIOS so I assume this came from Kensek.

(2) When installing the Thermalright HR-05 IFX heatsink, where did you folks put the thermal compound, on the SB/NB chip, or on the bottom of the HR-05? Thermalright actually lists in their instructions to put it on both. For me, it make sense to put it on the bottom of the HR-05, the surface area of that is less than my NB chip.

(3) For RAM, is anyone running 8GB on this board? I have 4GB but want 8GB, my mild overclocking indicates the RAM will be running at stock 1600 MHz speed, i.e. 400 FSB, 8.5 multiplier, 3400 MHz (3.4 GHz), 1600 MHz RAM speed. I remember Intel's DX48BT2 board warned against installing more than 4GB, I saw no such warning on this board.

Thanks all.
12-14-2008, 11:33 PM
MnM

Quote:

Originally Posted by aln688

(3) For RAM, is anyone running 8GB on this board?

Yeah I am. If you llok a few pages back (20? 30?) you will see my setting.
No problems what so ever with 8Gb and 64bit Vista.
12-14-2008, 11:37 PM
DerekT

Quote:

Originally Posted by Think

Anyone having corruption errors utilizing onboard Raid with 0 striping?

Running with 2 X 1TB RAID 0 Matrix and 2 X 1TB Speeding RAID 0. No issues. I have had to clone images back, but that was due to high FSB. Never an issue with failed RAID's. However, when the Speeding RAID 0 is enabled there is a halt while initializing in the Windows Boot. Halt is about 8 seconds.

Quote:

Originally Posted by MnM

Yeah I am. If you llok a few pages back (20? 30?) you will see my setting.
No problems what so ever with 8Gb and 64bit Vista.

8GB of Corsair 1600C7 running at 1600C7 (7-6-6-16 1T)

http://i259.photobucket.com/albums/h...08/Memtest.jpg http://i259.photobucket.com/albums/h...rekT2008/s.jpg

Quote:

Originally Posted by aln688

(1) What are these BIOS's that a user named "Kensek" is making, what is supposed to be special about them? Obviously Asus never released a 1001 BIOD so I assume this came from Kensek.

ASUS released a 1001 BIOS. I have it installed.
12-15-2008, 01:28 AM
rob2k

Quote:

Originally Posted by cheapseats

rob2k, I found your combination of 400 strap and CT Auto gives some very nice results at 475FSB/1:2 :)

With CT AUTO, the 400 strap is a lot faster than it was....

Hi Cheapseats, cheers for the very informative post - some interesting results :up:

Going to see if I can run my tRAS at your settings :)
12-15-2008, 07:31 AM
Think

Quote:

Originally Posted by DerekT

Running with 2 X 1TB RAID 0 Matrix and 2 X 1TB Speeding RAID 0. No issues. I have had to clone images back, but that was due to high FSB. Never an issue with failed RAID's. However, when the Speeding RAID 0 is enabled there is a halt while initializing in the Windows Boot. Halt is about 8 seconds.

Then one of my velicorators has failed after 2 months. Intel Raid 0 Rom indicates:

WDC WD1500HLS-0 (Error occurred (0)). I had my system imaged as well and re-installed but after a few hours I get BSOD and corrupt files. It might be the motherboard as well, not sure but I'm running the Maxtor 4.3 test on it to see.

Confirmed - Defective drive
12-15-2008, 07:48 AM
Ozzfest05

my watercooling setup is almost done and I should be getting the HAF 932 around the new year for it dont know what to do phase change the 1200 and H20 cool the HAF seems more logical but then I need to rebuild both pcs but either way you should see me running 5ghz or 5.3 24/7 on the 8600 the phase unit is slowly coming along hopefully before the new year it should be finished aswell just waiting on some parts
12-15-2008, 10:15 PM
aln688

Quote:

Originally Posted by DerekT

ASUS released a 1001 BIOS. I have it installed.

They did? I checked Asus's web-site, the latest is 901:

Description Rampage Extreme 0901 Bios
Fix if use 2 pieces of HD4870X2 to build CrossfireX it may get no display from the VGA card which is inserted in the PCI-E X16_1 slot
File Size 915.62 (KBytes) 2008/11/25 update

Maybe their FTP site has something newer?
12-15-2008, 10:18 PM
aln688

Quote:

Originally Posted by MnM

Yeah I am. If you llok a few pages back (20? 30?) you will see my setting.
No problems what so ever with 8Gb and 64bit Vista.

Excellent news, that inspires confidence that I can buy another 4GB of Kingston HyperX DDR3 1625 RAM modules and they'll work. I'll wait until around new year, hopefully they'll have a sale. Kingston's web-site discounts their RAM once it's in the basket, plus I have a 20% off coupon.
12-15-2008, 10:25 PM
aln688

A question to the overclocking gurus on this web-site...

If I'm overclocking my Q9550 stock 2.83 GHz to 3.4 GHz (FSB going from 333 to 400), do I need a fan on my Thermalright HR-05 which sits on the Northbridge chip? I have an HR-05 IFX/SLI on the SB and an HR-05 IFX on the NB. I'd really like to do away with the fan, but do have one if it's needed. I'm on air cooling only, no water cooling at all. I have 120x38mm Panaflo NMB-MATs on the front and rear of the case (one each), and a 92x25mm on the Noctua U9B CPU.

Thanks all.
12-15-2008, 11:59 PM
rob2k

Quote:

Originally Posted by aln688

...do I need a fan on my Thermalright HR-05 which sits on the Northbridge chip?

Hi Aln688, I would try without first and if it idles below 40 then you should be fine - this allows 20 degrees under load with a mild overclock. My N/B maxed out at 65 degrees with 420FSB and stock cooling so use this for your upper limit.
12-16-2008, 12:28 AM
mrcape

Quote:

Originally Posted by cheapseats

Hi, great mem, what vdimm, vtt, nb, sb voltages did you use for these tests?
12-16-2008, 04:34 AM
Think

Another failed drive!!! This one is my WD4000YR backup storage drive on this board with the same error when running Western Digital latest bootable test. What the hell is going on:mad:
12-16-2008, 10:27 AM
frank.lopez

Can't make OC stable at 3.6

I've manage to boot at 3.6, and the temps are good around 34ºC idle, but when i run prime95 I get errors, if i run prime's 1st option It works fine (Just CPU)

My System now is: Asus Rampage Extreme + Q9450 + Cellshock 14400 (1800Mhz) 8-7-6-21

Can anyone Please Assist?

My system Bios Looks Like this:

AI OVERCLOCK TUNER ==================== MANUAL
OC FROM CPU LEVEL ==================== AUTO
OC FROM MEMORY LEVEL UP ============== AUTO
FSB FREQUENCY ======================= 450
CPU RATIO SETTING ==================== 08

CPU CONFIGURATION:

CPU CLOCK SKEW ====================== AUTO
NB CLOCK SKEW ======================= AUTO
FSB STRAP TO NORTH BRIDGE ============= 400
PCIE FREQUENCY ====================== 100
DRAM FREQUENCY ===================== 1800
DRAM COMAND RATE =================== 2N
DRAM TIMING CONTROL ================= MANUAL
CAS LATENCY ======================== 8
RAS TO CAS DELAY ==================== 7
RAS PRE TIME ======================== 6
RAS ACT TIME ======================= 21
RAS TO RAS DELAY =================== Auto
REF CYCLE TIME ===================== 72
WRITE RECOVERY TIME ================ Auto
READ TO PRE TIME =================== Auto
READ TO WRITE DELAY S/D ============= Auto
WRITE TO READ DELAY S =============== Auto
WRITE TO READ DELAY D =============== Auto
READ TO READ DELAY S ================ Auto
READ TO READ DELAY D ================ Auto
WRITE TO WRITE DELAY S ============== Auto
WRITE TO WRITE DELAY D ============== Auto
WRITE TO PRE DELAY ================== Auto
READ TO PRE DELAY=================== Auto
PRE TO PRE DELAY==================== Auto
ALL PRE TO ACT DELAY================= Auto
ALL PRE TO REF DELAY================= Auto
DRAM STATIC READ CONTROL =========== DISABLED
DRAM DYNAMIC WRITE CONTROL ========= DISABLED
DRAM SKEW CONTROL ================= Auto
AI CLOCK TWISTER =================== Auto
AI TRANSACTION BOOSTER ============= STRONG
COMMON PERFORMANCE LEVEL ========== AUTO
PULL-IN OF CHA PH1 ================= DISABLED
PULL-IN OF CHA PH2 ================= DISABLED
PULL-IN OF CHB PH1 ================= DISABLED
PULL-IN OF CHB PH2 ================= DISABLED
EPU II PHASE CONTROL =============== AUTO
CPU VOLTAGE ====================== 1.40
LOAD-LINE CALIBRATION ============== ENABLED
CPU PLL VOLTAGEM ================== 1.55081
FSB TERMINATION VOLTAGEM ========== 1.40
CPU GTLVREF 0 ===================== +50
CPU GTLVRED 1 ===================== +50
CPU GTLVRED 2 ===================== +50
CPU GTLVRED 3 ===================== +50
NB GTLVRED ======================= +60
NORTH BRIDGE VOLTAGE ============== 1.55
DRAM VOLTAGEM ==================== 1.90
NB DDRVREF ======================== AUTO
DDR3 CHANNEL A VREF ================ AUTO
DDR3 CHANNEL B VREF ================ AUTO
SOUTH BRIDGE 1.5 VOLTAGE =========== 1.51106
SOUTH BRIDGE 1.05 VOLTAGE ========== 1.06039
CPU SPREAD SPRECTRUM ============== DISABLED
PCIE SPREAD SPECTRUM ============== DISABLED

ADVANCED CPU CONFIGUTION:

CPU RATION SETTING ================= 08
C1E SUPORT ======================== DISABLED
CPU TM FUNCTION =================== DISABLED
MAX CPUID VALUE LIMIT =============== DISABLED
VANDERPOOL TECHNOLOGY ============= ENABLED
EXECUTE DISABLED BIT ================ DISABLED
CORE MULTI- PRECESSING ============== ENABLED
12-16-2008, 10:57 AM
aln688

Quote:

Originally Posted by Think

Another failed drive!!! This one is my WD4000YR backup storage drive on this board with the same error when running Western Digital latest bootable test. What the hell is going on:mad:

So that's two drives you've had fail? If I were you I'd put your motherboard settings back to stock see if that makes a difference. Could it be your motherboard SATA controller (ICH9R?) is corrupting your drives somehow?

Show 100 post(s) from this thread on one page