New RAM List!!! (now with 1GB stick listing too)

Printable View

Show 100 post(s) from this thread on one page

05-31-2005, 06:31 AM
gplracer

I have a DFI Infinity NF2 board that does 250fsb 1:1. Currently I have a 512mb stick of Corsair 3500 c2. What would be another good stick of 512 to add to this combination? Also is there a stick that would be good later in a A64 motherboard too? I was thinking TCCD but I really do not know. Thanks!!!
05-31-2005, 07:38 AM
Punisher!

Quote:

Originally Posted by FLD

If my sticks have 2.5-3-3-7 timings and don't boot at 3-X-X-X can I safely say that they are BH-5? Some onealready conviced me of this but just wanted to make sure.

Thanks a lot.

Yeah, they are.
05-31-2005, 07:52 AM
13oost

need to update the OCZ value ram
06-01-2005, 02:45 PM
ALXgr

Quote:

Originally Posted by andyOCZ

Getting the PC4200 Platinum or PC4800 Platinum will insure you get TCCD. The PC3200 Plat Rev 2 uses the TCC5 as does the PC3700. The TCC5 does low latency 2-2-2 timings better.

Quote from insanetek
UPDATE:
While my sample of the PC4800 came with TCCD IC's, OCZ says that all current and future PC4800 memory will come with TCC5 chips. This is certainly not a bad thing. Just because it uses a different IC doesn't mean you'll get less overclock. If you check the PC5000 review, you'll see that that memory featuring TCC5 overclocked better than my PC4800 sticks that feature TCCD. This update is just to let you all know that PC4800 will be using TCC5. I probably just got lucky with my sample.

Any further info about this??
06-01-2005, 03:36 PM
dippyskoodlez

TCC5 isnt BAD... its a GOOD thing people... so many people freak out over little changes :(

(not pointing out that user specificly, but it generalyl seems like people are freaking over TCC5.)
06-01-2005, 11:29 PM
ALXgr

TCC5 is not bad ,not at all...I'm sure that ocz 4800 will do ddr600 but if they use tcc5 the list must be updated!

EDIT : same update from overclock intelligence Agency
06-02-2005, 09:41 AM
Punisher!

Quote:

Originally Posted by ALXgr

TCC5 is not bad ,not at all...I'm sure that ocz 4800 will do ddr600 but if they use tcc5 the list must be updated!

I am waiting news from AnyOCZ...
06-02-2005, 12:22 PM
TEDY

anyone have any info of Samsung UCCC or TCCC ?
06-02-2005, 12:26 PM
Punisher!

Quote:

Originally Posted by TEDY

anyone have any info of Samsung UCCC or TCCC ?

They are on list... I had two of those modules:
http://m4tribes.m4d.it/puni/CPU-Z_RAM1.jpg

+250 Mhz @3-4-4-8 Rock Solid @ ~2,8V Dual Channel of course.
06-02-2005, 12:30 PM
TEDY

what about 2.5-3-3-x ? :)
06-03-2005, 05:17 AM
Punisher!

Quote:

Originally Posted by TEDY

what about 2.5-3-3-x ? :)

Over 200 but I don't remember exactely how much.
06-04-2005, 05:33 PM
andyOCZ

Quote:

Originally Posted by andyOCZ

Getting the PC4200 Platinum or PC4800 Platinum will insure you get TCCD. The PC3200 Plat Rev 2 uses the TCC5 as does the PC3700. The TCC5 does low latency 2-2-2 timings better.

Hi, I just found out the PC4200, PC4800 and PC5000 are all TCC5 now. It looks like we have switched over completely. All former TCCD is now TCC5.

If I don't look at the markings I can't tell anyway. :)

TCC5 = TCCD
06-07-2005, 10:27 AM
Vassili

1 Attachment(s)

anyone know which chip this Kingston HyperX 512MB PC2700 is using?
http://xtremesystems.org/forums/atta...id=32089&stc=1
06-08-2005, 03:16 PM
ALXgr

My brand new OCZ pc4800 platinum V1.1=>TCC5

http://img114.echo.cx/img114/127/im0004616kr.jpg

So if you want to identify tcc5 from tccd look at the bottom right of the stickers for V.1,1
06-19-2005, 12:53 PM
theobub

Quote:

Originally Posted by TEDY

anyone have any info of Samsung UCCC or TCCC ?

I had a pair of TCCC sticks. I only tested them on my 32 bit system (NF7-S rev. 2 + 2500Mobile), they could run 205Mhz 2-2-2-7 and beyond that on 2,5-3-3-8 up to 235Mhz no memtest errors, they wouldnt get stable at 250Mhz no matter how relaxed I got the timings. But that was on Nforce 2 chipset, never tested them on Nforce 4. It would be an interesting thing to do, if only I had not sold them over to a friend, but I will try to get them for testing tomorrow, and post the later on..
06-19-2005, 11:44 PM
Kasparz

http://www.ocztechnology.com/product...0_dual_channel
Doe's anyboby know, what chips uses this ram?
OCZ today incoming :woot:
06-20-2005, 12:13 AM
TEDY

Quote:

Originally Posted by Kasparz

http://www.ocztechnology.com/product...0_dual_channel
Doe's anyboby know, what chips uses this ram?
OCZ today incoming :woot:

stay away from these....
06-20-2005, 06:17 PM
FiNcH64

Quote:

Originally Posted by God_Lx

If they-re CH-5 they i'll do better... (Or maybe not all CH-5 is that great) i have some CH-5 and it does 215Mhz 2-2-2-5 @ 2.7vdimm (Didn't try higher even) (They do 2-2-2-5 @ 200Mhz with default vdimm but i get some memtest errors...)

dude i got a pair of mushkin pc3500 level one 512mb x 2 and they overclock so damn great..

can run them to 245mhz 3.3 v

250 mhz with 3.4v for benchmarks dont want to toast them so nothing 24/7 only when i get my redline pc4000.. hehe

you most have gotten some bad sticks dude ;)
06-20-2005, 07:08 PM
thezfunk

this Powerbrain PBC...whats so good about it...read this whole thread and didn't see an answer...
06-20-2005, 07:21 PM
ahmad

Quote:

Originally Posted by thezfunk

this Powerbrain PBC...whats so good about it...read this whole thread and didn't see an answer...

BrainPower PCBs tend to overclock better than the standard or enchanced JEDEC PCBs. Why, I don't know. But they are a lot cheaper to produce than JEDEC PCBs thats for sure (its also rumoured that the BP808 do better than the BP815 PCBs...).
06-20-2005, 08:32 PM
Punisher!

Quote:

Originally Posted by ahmad

BrainPower PCBs tend to overclock better than the standard or enchanced JEDEC PCBs. Why, I don't know. But they are a lot cheaper to produce than JEDEC PCBs thats for sure (its also rumoured that the BP808 do better than the BP815 PCBs...).

Exactely.

BP PCB is a 6 layer PCB, so it has less elettric noise than JEDEC (and this mean more overclock) and moreover it is cheaper to be produced.
06-20-2005, 08:43 PM
thezfunk

OK, I have a NForce2 and I am looking at some new ram. Winbond chips don't play nice with my board...especially not BH-5. I am going with TCCD with PB PCB hopefully. Can you safetly run TCCD ram over 3.0v and does it show any improvement?
06-20-2005, 09:06 PM
FLDQUY157

Quote:

Originally Posted by Punisher!

Exactely.

BP PCB is a 6 layer PCB, so it has less elettric noise than JEDEC (and this mean more overclock) and moreover it is cheaper to be produced.

Wow, cheaper and better!!! Hmm...very interesting.
06-20-2005, 11:47 PM
thezfunk

http://www.monarchcomputer.com/Merch...AFFIL=FRG&NR=1

This is TCCD right?

Well I am going to get it...turns out it is on 815 instead of 808 but for that price I can't say no. All reviews I have seen it hit 275+
06-21-2005, 06:46 AM
CJ4

Quote:

Originally Posted by CJ4

The information for the Mushkin Blues is mostly correct if they were ordered recently from Outpost/Fry's. The dual packs were with the BH die, the single packs were with the CH die. The Mushkin Blues also had about 100 pieces of BH-5 on the Jadec PCB thrown in. The older Mushkin Blues had mosel chips.

http://www.ocforums.com/showpost.php...&postcount=191

Any update for this, or is more required?

CJ
06-21-2005, 08:40 AM
Punisher!

Quote:

Originally Posted by CJ4

Any update for this, or is more required?

CJ

Sorry, but in this period I am a bit busy for my University exams (last 3 for this year, "business school" is one of the last in Padua to end!!) :D
06-22-2005, 07:32 AM
TEDY

how good are

2x 512 MB GEIL DDR500 PC4000 UltraX Platinum

TCCD 100% ?
06-22-2005, 02:08 PM
TEDY

GEIL
DDR500 CL=2,5-7-4-4
GL1GB4000DC
PN0649-SN400xxxx

TCCD ?
06-23-2005, 03:53 AM
Vassili

Kingston Ram w/remarked Chips as D328DW-5 --chip--> Winbond BH-5
Kingston Ram w/remarked Chips as D328DW-6 Winbond BH-6
Kingston Ram w/remarked Chips as D328DM-6 --chip--> should Winbond BH-6
Kingston Ram w/remarked Chips as D328DM-5 --chip--> should Winbond BH-5

From the startpost, but that doesn't make sense does it? 2 different labels for BH-5/BH-6. Shouldn't one be CH/UTT?
06-29-2005, 02:15 AM
kristos

ocz_el_ddr_pc_3500_gold_gx_dual_channel

anyone know what chips these carry?
07-01-2005, 11:17 AM
high5

utt bh most likely. its basically the same stuff as gold pc3200, just rated higher.
07-01-2005, 11:42 AM
j_p_h2002

Are on DDR2 Ram always the same chips? no? When yes, what chips are on the ram from OCZ(PC-667 4-2-2-8)?
07-02-2005, 04:30 PM
sphish

I've got some Mushkin L2V2 2x512 right now, but I'm planning on getting 4x512mb and instead of getting another set of l2v2 mushkin, I'm debating 2 sets of OCZ Gold 2x512 (New BH-5).

Couple of questions, anyone have any experience with this at 2.7-2.9v? Does it do the 2-2-2-5 timings? How far has anyone been able to push it?

Should I just get another set of Mushkin L2V2?

Board's a DFI NF4 Ultra-D, newest bios, and I'll be upgrading my Winchester 3000+ to an x2-4200 within the next month. Any input would definitely be appreciated!
07-02-2005, 11:15 PM
high5

ocz rates them 2-2-2@200 w/ 2.8v so it shouldn't be a problem. with 2.9v you can expect to get them to do something like 220 i think.
07-07-2005, 10:16 AM
oziris1978

The New A Data Pc4500 Have New Samsung Tcc5 Chips!!!
07-07-2005, 02:52 PM
b1tterman

could someone compare d5 chips(maybe kingmax ddr500) with something else like TCCD and UTT/BH-5 in tight,medium and loose latencies please, i got them and dunno how high i may clock with them. thx
07-07-2005, 05:33 PM
suio

Which TCCD based memory works best with DFI NF3 250 board?
07-07-2005, 07:26 PM
FiNcH64

about the corsair pc4400 c25 chips are samsung tccd???

hey guys, im about to buy a pair of this memos for a 1gb dual channel kit.. i have to purchase them separatly cause they dont have twinx pairs. so i hope they give me the same perfomance as the ones selled as twinx..

so my question is.. if are you sure that this sticks are samsung tccd?? cause i have seen good reviews about them but i dont want to get wrong and get some hynix 5, or vitelic 5ns :mad: ..

so i appreciate that someone confirm that this are super cool samsung tccd as in the ram list!! is speciefied hehe :D

thx
07-08-2005, 11:07 PM
Zanr Zij

@Punisher :

1. Corsair TwinX1024-3200 v6.1 :< PCB same as XLPT v1.2 ( Brain Power )>

http://www.xtremesystems.org/forums/...&postcount=208

Result : @3.5v

http://img276.echo.cx/img276/9624/ddr5209vi.jpg

==> UTT BH-5 IC

2. Corsair TwinX512-3200C2PT v1.7 : PCB same as XLPT v1.2 ->Brain Power.

http://www.xtremesystems.org/forums/...&postcount=212

Result :@3.6v

http://img74.imageshack.us/img74/3919/28spi3ql.jpg

==> UTT BH-5 IC

:D
07-10-2005, 04:21 PM
Punisher!

Quote:

Originally Posted by Zanr Zij

@Punisher :

1. Corsair TwinX1024-3200 v6.1 :< PCB same as XLPT v1.2 ( Brain Power )>

http://www.xtremesystems.org/forums/...&postcount=208

Result : @3.5v

http://img276.echo.cx/img276/9624/ddr5209vi.jpg

==> UTT BH-5 IC

2. Corsair TwinX512-3200C2PT v1.7 : PCB same as XLPT v1.2 ->Brain Power.

http://www.xtremesystems.org/forums/...&postcount=212

Result :@3.6v

http://img74.imageshack.us/img74/3919/28spi3ql.jpg

==> UTT BH-5 IC

:D

Nice, thanks a lot! :D
07-11-2005, 05:10 PM
[XC] DragonOrta

Quote:

BrainPower PCBs tend to overclock better than the standard or enchanced JEDEC PCBs. Why, I don't know. But they are a lot cheaper to produce than JEDEC PCBs thats for sure (its also rumoured that the BP808 do better than the BP815 PCBs...).

How would I find out which BP PCB I have on my G.Skill LA?
07-12-2005, 12:50 AM
andyOCZ

Quote:

Originally Posted by DragonOrta

How would I find out which BP PCB I have on my G.Skill LA?

Look at the markings on the end of the module. You will see "B6U808" or similar if it's Brainpower.
07-13-2005, 08:38 AM
[XC] DragonOrta

ok, Thanks Andy.
07-13-2005, 11:45 AM
railer

Punisher i got my ram to 301MHz http://www.xtremesystems.org/forums/...101#post954101
So you can update the Kingmax Hardcore series section in your post. At least 1 product from them deservs to be in this thread. To bad i didnt find your thread sooner then i would knew that OCZ VX is UTT an would not bout them for my Dothan rig. Exelent thread by theway :up:
07-13-2005, 12:43 PM
Punisher!

Quote:

Originally Posted by railer

Punisher i got my ram to 301MHz http://www.xtremesystems.org/forums/...101#post954101
So you can update the Kingmax Hardcore series section in your post. At least 1 product from them deservs to be in this thread. To bad i didnt find your thread sooner then i would knew that OCZ VX is UTT an would not bout them for my Dothan rig. Exelent thread by theway :up:

I will... sorry but I am a bit busy! :D
07-17-2005, 12:01 AM
Punisher!

List updated:
Addings (A) or editings (E):
GeIL ONE (A)
GeIL ONE BH (A)
G.Skill ZX (A)
G.Skill FR (A)
G.Skill FC (A)
OCZ PC4200 (A)
OCZ PC4800 PE (A)
OCZ PC4800\PC5000 (E)
KingMax Hardcore BGA --> Hynix B (A)

Several other not listed editings. Find them on the List :p:.

If I forgot some addings or editings or if you want to report some "not listed" memories just tell me! ;)

Bye! :D
07-18-2005, 11:07 AM
biohead

how do I find out if my corsair 3200xl's are v1.1 or v1.2 ? Is there any difference between them in oc and/or voltage needs?
07-18-2005, 11:26 AM
high5

you can read it from the sticker on the heatspreaders.

v1.2 is generally better for oc-ing since it utilizes brainpower pcb which maximizes the performance of tccd ic's.
07-18-2005, 11:51 AM
IYP

:stick: :kittenhat :hump:
07-21-2005, 05:00 PM
tturbo

I was wondering if anyone knows what chips are in my ram. I just got them back from RMA. I had rev 1.1 before and they wouldnt get past 220 bus :( so I had to rma them. The new set are the following:

Corsair PC4000 memory.

CMX512-4000PT
XMS4000v3.4
0526123-1
07-22-2005, 04:05 AM
high5

go to corsair supports forums and post that info in 'ic inquiry thread'.
07-22-2005, 06:09 PM
PanaBob

Bh-5?

so is this the Mushkin "Promo" Build w/ BH-5?

http://www.newegg.com/Product/Produc...82E16820146353
07-23-2005, 06:02 AM
dippyskoodlez

Quote:

Originally Posted by PanaBob

so is this the Mushkin "Promo" Build w/ BH-5?

http://www.newegg.com/Product/Produc...82E16820146353

Thats tccd/tcc5.
07-23-2005, 11:03 AM
ImportantAwareness89

What's the difference between UTT (OCZ VX) and New BH-5 (Mushkin Redline). I always thought the two rams were basically identical
07-23-2005, 11:07 AM
TheMeatFrog

Quote:

Originally Posted by dmo580

What's the difference between UTT (OCZ VX) and New BH-5 (Mushkin Redline). I always thought the two rams were basically identical

Same here :slap: :confused:
07-23-2005, 02:48 PM
HARDCORECLOCKER

:D AFAIK Winbond UTT can be either new BH-5 or new CH-5 based - so the addition "BH-5" classifies it definately.

:toast:
07-26-2005, 06:28 PM
HiJon89

This RAM is definitely BH-5 right? I just want to make sure before I buy it.

First stick is:
KHX3500/512R
9905200-011.A00
1199838 - 2.5v

Second is:
KHX3500/512
9905200-011.A00
1070861 - 2.5v
07-26-2005, 06:34 PM
HiJon89

Quote:

Originally Posted by dmo580

What's the difference between UTT (OCZ VX) and New BH-5 (Mushkin Redline). I always thought the two rams were basically identical

Redline and VX are both UTT-CH on BP PCB so they are basically identical. There are also UTT-BH chips which are used in RAM such as OCZ Gold 3200, OCZ Gold 3500, and GSkill GH
07-26-2005, 06:35 PM
Zanr Zij

Quote:

Originally Posted by HiJon89

This RAM is definitely BH-5 right? I just want to make sure before I buy it.

First stick is:
KHX3500/512R
9905200-011.A00
1199838 - 2.5v

Second is:
KHX3500/512
9905200-011.A00
1070861 - 2.5v

yes ! Both are BH-5. R ( KHX3500/512R ) stand for Retail :)
07-26-2005, 06:41 PM
HiJon89

Quote:

Originally Posted by Zanr Zij

yes ! Both are BH-5. R ( KHX3500/512R ) stand for Retail :)

Great, thanks :toast:

Show 100 post(s) from this thread on one page

All times are GMT -8. The time now is 03:26 PM.

XtremeSystems