hey Tictac, any ideas as to what timings to use for BH-5/6 Nothing too aggressive though.
Printable View
hey Tictac, any ideas as to what timings to use for BH-5/6 Nothing too aggressive though.
hey Tictac, any ideas as to what timings to use for BH-5/6 Nothing too aggressive though.
hey Tictac, any ideas as to what timings to use for BH-5/6 Nothing too aggressive though.
hey Tictac, any ideas as to what timings to use for BH-5/6 Nothing too aggressive though.
hey Tictac, any ideas as to what timings to use for BH-5/6 Nothing too aggressive though.
hey Tictac, any ideas as to what timings to use for BH-5/6 Nothing too aggressive though.
hey Tictac, any ideas as to what timings to use for BH-5/6 Nothing too aggressive though.
I was referring to the actual fan.
7 back to back identical posts, new world record! :lol:
crap! lol
hey what is your actual spec?(Proc, memory , VGA , PSU?) :confused:Quote:
Originally Posted by situman
if you want to test your memory .... 1st lower your multiplier
then max out your memory and see where they max out..... :)
try mutliplier 7
VCore : default
Vdimm : 3.2v-3.5v :D
DDR VTT : DDR/2
HT Frequency : 4x
HTT Start from 200MHz( increase by 5Mhz interval)
test stability with Super PI then 3d mark 2001.....
Bios memory timing :
DDR Clock : DDR400 (Sync 1:1)
CAS Latency : 2
row cycle time : 7
row refresh cycle time : 14
ras to cas delay : 2
ras to ras delay : 2
min ras active time : 5
ras precharge time : 2
write recovery time : 2
write to read delay : 1
read to write delay : 2
Dram command rate : 1T
burst length :
bank interleaving : enable
Good luck... :toast:
p/s: whats up with multiple reply? :slapass:
might want to disable bank interleave for UTT/BH5 and keep it enabled for TCCD
Quote:
Originally Posted by tictac
i tried 1T once and the system powered down even before i got into windows.
Specs:
AN8 SLI
Venice 3200
Powercolor X800XL
Raptor 74gb
PCP&C 510 SLI
Stock cooling.
I tried as low as 3x HTT but stayed with 10x and I use 333 mem divider. Using 1T the system just powers down without going into windows. I wonder if its a bug or another Asus A8N SLI. ANyways I havent tested it out enough to say for sure. I wont be able to for another week or so. Waiting for a waterblock.
results tomorrow, worked ot and too tired to mess with it. i got a ton of pics to post :woot:
YES IT FITS!!!!! I built one for my friend using the XP90 cooler. U have to take off the stock cooler retentioner and use the one supplied with the XP90 and use the screws that comes with the thermalright. It screws right on the backplate. U CANNOT USE THE SCREWS that came with the mobo!
http://www.jab-tech.com/customer/pro...cat=169&page=1
Situman... that doesn't look good :(
Post some pic/screenies :slapass:Quote:
Originally Posted by rancid
Rancid did u get 1T to work at least? Maybe I should have disabled bank interleave. I left it enabled.
3.55v?
Again it was late and not much time. My trusty Muskin BH5 did not make it through 235 MHz @ 3.1 Volts but I will did juice it up some more just now. Still getting a feel for the board.
I hope you set it to cas1 from within bios, otherwise it didnt change it (you cannot adjust cas latency from anywhere except the bios).
:( damn
hmmmmm another excuse.... :slap: damn OC this :banana::banana::banana::banana::banana:....squeez e the living daylights out of it...someone pls show some serious numbers
Quote:
Originally Posted by Sheik
Ok the best I can do so far with my old Mushkin BH5 DDR433 @ 3.55V
SuperPI 1m / 3DMark2001 / Sciencemark stable. Good enough for me.
No A64 Tweaking.
Not too bad at all.
:woot: 266MHz 2-2-2-6 :banana:Quote:
Originally Posted by Sheik
thats what i been waiting for...
should be enough for my TwinMOS SP
thanks for the review :clap:
Glad you like. Doesn't seem to like my TCCD at all so far though :(