Printable View
Seriously? I have the Giga K8NS Pro as well. I've been able to run Super Pi up to 3.5 volts, don't want to try any more without better cooling. But I can't run 3D benches past ~220 fsb with my BH-5s at any voltage. What DIMM slots did you put the memory and the booster in?Quote:
Originally Posted by Kunaak
Im thinking about ordering a booster, though i have the ic7-g. im wondering about this vtt mod the ic7 series needs for the booster. how would i go about doing this :confused: just a quick description if its ok
Yes :):DQuote:
Originally Posted by dutchman.pt
the max vdimm you can reach? 3.8? 3.9 ??
ciao
Alessio
I too own an IC7 and OCZ recommend that the VTT mod is performed, it really holding my DDR500 back (3.5ns), anyone here from the UK willing to do the mod for me, dont fancy it myself :stick:Quote:
Originally Posted by mastrcronX
Cheers guys.
hi all. quick question. will this be possible with the booster:
set bios voltage to 2.9vdimm, adjust booster to 3.2vdimm, and from bios, will i be able to set 2.9-3.2 real, 2.8-3.1 real, 2.7-3.0 real, and 2.6-2.9 real?
or, will i have to adjust voltage explicitly from the booster and leave bios at either 2.6 or 2.9?
board is NF7-s rev. 2.
thx:)
I don't think adjusting v via BIOS after dialing up the Booster is a good idea. Similar to the situation that roasted many A64's. NF2 may be a different ballgame however.
But why do it that way when you have the booster anyways? Just leave the case side off;)
would be so much easier to adjust in bios.. oh well, i guess i can just reach in and adjust while testing.
should i set it to 2.6 or 2.9? on some older nf7's vtt tracks with vdimm past 2.9. i have an older nf7 (and am hoping it tracks on this board). will vtt track with the booster's outputted vdimm while keeping setting 2.6 in bios, will 2.9 work better, or it won't matter?
thx for your reply:)
Dunno bout vtt tracking. I would set 2.6 in BIOS, and dial up the ram juice from there. Just check it in stages to verify stability. And with your memory I would not stop until around 3.6v anyway, then you might see something happen;)
Quote:
Originally Posted by dutchman.pt
Does the Booster work on the DFI Lanparty Nforce3 250Gb socket 754 ?
Quote:
Originally Posted by Drisler
And whats the max Voltage, you can drive with it on the DFI Lanparty UT nf3 250 GB???
greetz free
I've been up to 3.8v until all hell broke loose @274x11 1:1
i have a ic7 max3 and a ddr booster without the vtt mod i was not able to boot with the ddr booster and some ocz pc 4000 gold ,it did boot fine with the booster and some muskin pc 3500 after vtt mod that problem was solved.
so i believe u really need vtt mod on a ic7 if you want a booster.
also ocz advised me not to go over 3.3v in a reply they send me. heres what they said:
It is risky to go above 3.4 in any circumstance, but the issue lies with the
power regulation of the board. I would advise you don't go above 3.3 VDIMM
on the IC7 Max3.
well my ic7 just died, so i ordered a lanparty pro875b, no vtt mod for me :) that is if my booster is compatible..
Oczbooster with this P5P800? The connection in OCZBooster in cable 20Pin..and P5P is 24Pin!! :rolleyes:
http://site.voila.fr/mrfreeze/oczhs.jpg
i think my psu do that
now it ok I repair
Got a rev. 2 booster cheap and desided to test it on my Albatron PX875P Pro, didn't give much of a result thoug :(
Maximum bios setting is 2,8V for the vdimm, and I can't go higher with the booster, if I set the booster to 2,8V there is black screen and no boot :(
Looks like I'll need a new mobo...
EDIT: just for the record: ram is in slot 1 and 3, and booster in 4
EDIT2: Took the booster out and set vdimm in bios to 2,8V, turned off computer and put back booster, display on booster showed 2,9 and computer booted just fine, ran superpi and so on.., now restarted the computer, turnede the thing on the booster so it showed 3,0V, computer booted, but i turned it off because the little alu profile got DAMN HOT (auch my poor finger :doh: )
I have a 80mm fan blowing above the ram sockets and a 40mm fan blowing at the aluprofile...
I installed it on an Asus P4C800 (none deluxe, none -E) and I guess it works (Mushkin Special PC3200 @250 CL2 2-2-5)
but.. I LED readout does not work, I don't see how much voltage I'm pushing through the chips;
the DDR booster works perfect in my MSI K8N Neo, but no display on the Asus PC4800, is this normal?
Somebody has tried the OCZBooster with DFI 875P-T?
tHZ
Has this been done this yet?? and if so, why isn`t it in the first post of the thread?Quote:
Originally Posted by Kunaak
has anybody probed it on a soltek 75frn2-l???
when it will work with DFI NF2 INFINITY ?
Quote:
Originally Posted by CarNabY
FUGGER has on his excursion to 6GHz+...
i'd like to knwo this to ...Quote:
Originally Posted by goddh0r
the ocz webstite doesnt mention this board.
:stick:
That is exactly my question? I have the booster right now, and will either order the neo2 or if dfi ever delievers the nf3 or nf4 939 board.. I would suspect if you have DC that using slots 1 & 2 for 512mb x 2 would be the best choice and then puting the booster in slot 4, but not 100% sure if slots 1&2 are the best choice, and also will the the memory and booster even fit in this configuration....?Quote:
Originally Posted by Razor_cut
Quote:
Originally Posted by Jasonxxx
i have a winchester 3200 in a neo2. DIMMs 1&2 house my ballistix and DIMM 4 the booster. it is a snug fit with the booster just clearing the heatspreader of the DIMM in slot 2.
currently running them at 2.5-2-2-9 1T @ 270MHz with 3.4Vdimm.
been prime blend test stable for past 5 hours and still running.
without the booster I couldnt get stable at 2.5-4-4-9 1T @ 253+MHz with 2.85Vdimm(motherboard max) so its a good combination.