Printable View
I'd assume jabtech and other resellers have the latest/final revisions of the top/reservoir in stock? Does the pump/reservoir combo allow compression fitting size of 1/2'' with OD tubing size of 3/4"" http://www.jab-tech.com/Swiftech-MCP...p-pr-4750.html
No, Gabe has not replied that it's done yet. Will have a delryn top and fit 3/4" OD compression fittings.
So no, we are still waiting.
Will the pump run at 100% if the pwm is not connected to a fan controller/motherbaord?
:yepp:Quote:
Originally Posted by Big Myke
Is only the res getting a revision, or the non-res pump top as well?
Res atm only comes with delerin top.that is the stock top for mcp-35x.
I haven't read anybody different.
Sent from my X10a using Tapatalk
Is the delrin top the final revision? I don't need the reservoir so if that is the only thing being updated I can buy the pump and top immediately.Quote:
Originally Posted by MagisD
So where can one buy MCP 35X in Europe? I can't find a single shop, not even Swiftech store has these! O.o
Dont do this plz! I promised myself not to upgrade anything for at least 6 months :shakes:Quote:
Originally Posted by zalbard
Also looking for European shop, waiting on one of these for new build, any ETA Gabe?
AFAIK, only higflow has it on stock (in Europe) - http://www.highflow.nl/pompen/laing-...p35x-pump.html
Cheers! Order placed! :up:Quote:
Originally Posted by k0ST
so will a 1/2ID 3/4OD compression barb fit on this pump?
Yes standard g1/4 ports.
Sent from my X10a using Tapatalk
Yes, your fittings will work fine on the pump. It's the top/res that is restricted to smaller fittings. Hopefully a newer revision will correct this issue, as well as others soon.Quote:
Originally Posted by Xel_NaGa
Gabe, any update on the res release date?
Anything yet?
New! (12-30-10) : Revision 2 of the MCP35X reservoir is now shipping. It supports compression fittings for up to 3/4" (tube OD) as shown below, and features an additional port inside of the fill-cap, that can be used to install a remote fill-port.
http://www.swiftnets.com/assets/imag...s-rev2x250.jpg
The compression fittings above are shown for demonstration purposes only, and sold separately by Swiftech resellers. The shipped product includes a set of Swiftech barb fittings, and G1/4 port plugs.
Nice!
I could see myself making use of that fill-port option...:)
this might be a stupid question, but doesn't the sponge thing to prevent cyclones from forming reduce flow rate?
Nice :)Quote:
Originally Posted by gabe
If I may ask, why didn't you go with the Delrin for the top? I'm a bit worried about it's weight like MagisD...
The EK RMA thread got me thinking about materials, so I'm wondering if the res is extruded or cast acrylic?
Can't wait until Sidewinder gets this in stock!
I wouldn't think so. That is not a sponge; its actually very porous; more like a mesh.Quote:
Originally Posted by Boogerlad
Have we consluded that this pump is worth the cost over a 355? I imagine its more worthwhile with the new design.
I haven't hooked up the V1 of the 35X res yet, but the Mini-Tank from Bitspower did perform better without the sponge. Also, the Swiftech sponge looks much less dense than the BP sponge.
Now I want to get that reservoir mounted... hmmm. :)
could one take out the sponge and prevent the cyclone from occurring if the res was completely filled?
Thanks Gabe, waiting for it to show up at stores. Finally get to rebuild.....