MaximusIV-Extreme Thread

Printable View

Show 100 post(s) from this thread on one page

10-03-2011, 10:37 AM
MonsterDK

Quote:

Originally Posted by badatgames18

why does your vdimm read 1.627v when set to 1.65v? that could be it... i think martin was trying to say your memory isn't getting enough voltage..(if it was rated for 1.65v) disable all the power saving features and then try to boot again.

If you have one take a dmm and measure dram voltage to see what it is during startup.

cheers

I made a post above if anyone can help please?

But to update with all C States other than the Package C State Limit (C6) are DISABLED.

And in Probe II I'm seeing 1.627V for Dram voltage :|

Anyone help - maybe Mushkin ram just does not need 1.65V?
10-03-2011, 11:16 AM
badatgames18

Quote:

Originally Posted by MonsterDK

I made a post above if anyone can help please?

But to update with all C States other than the Package C State Limit (C6) are DISABLED.

And in Probe II I'm seeing 1.627V for Dram voltage :|

Anyone help - maybe Mushkin ram just does not need 1.65V?

set dmm to 2000mV and measure...
yes turn c6 off(set to no limit) and see if it works... also try going back to defualt ram settings.

hope it works.

EDIT: btw... since it's a startup problem.. have you tried reconstructing your mbr?

cheers
10-04-2011, 08:14 AM
MonsterDK

1 Attachment(s)

Attachment 120798

Quote:

Originally Posted by badatgames18

set dmm to 2000mV and measure...
yes turn c6 off(set to no limit) and see if it works... also try going back to defualt ram settings.

hope it works.

EDIT: btw... since it's a startup problem.. have you tried reconstructing your mbr?

cheers

Quote:

Originally Posted by badatgames18

set dmm to 2000mV and measure...
yes turn c6 off(set to no limit) and see if it works... also try going back to defualt ram settings.

hope it works.

EDIT: btw... since it's a startup problem.. have you tried reconstructing your mbr?

cheers

Hi,

I have to say I'm not confident with a dmm which is why I want to get clarification and know I'm going to do this right.

Q1: So I turn the dial to the area marked on the picture and connect the probes to the ones shown in red and black representing the red and black leads.

Q2: Then once I have connected the motherboard probe cable I test it by connecting in no particulate order the red and black cable to the cable ends?

Q3: And I can take the reading at any time or during boot up etc?

thanks
10-05-2011, 04:12 AM
Timoleros

Hi guys!
I changed my UD4 with MIVE and i bought a new 2500K because my previous is dead (my previous was a X55 on UD4)
After a lot of tries i didn't make to boot in to windows desktop with more than X50 multi...
When i try to boot with more than X50 the system freezes at windows logo and the debug led shows AA..is there any chance to boot in the desktop or is a wall?

Thanks!
10-05-2011, 07:28 AM
bro20000

Sounds like a bad chip mate!
10-05-2011, 11:59 PM
stasio

MaximusIV-Extreme
ftp://ftp.asus.com.tw/pub/ASUS/mb/LG...-ASUS-2001.zip
Maximus_IV_Extreme-Z
ftp://ftp.asus.com.tw/pub/ASUS/mb/LG...-ASUS-0902.zip
MaximusIV-GENE-Z
ftp://ftp.asus.com.tw/pub/ASUS/mb/LG...-ASUS-0902.zip

Fix list basics are:
1) S3 resume with CPU PLL OV Enabled is patched - should work on most DRAM (cheaper ICs may have issues).
2) Ivy Bridge Support enabled.
10-06-2011, 02:00 AM
Martin.v.r

bios 2001 is ok ;)
http://img685.imageshack.us/img685/5923/nybios2001.png
10-06-2011, 07:16 AM
andressergio

Quote:

Originally Posted by stasio

MaximusIV-Extreme
ftp://ftp.asus.com.tw/pub/ASUS/mb/LG...-ASUS-2001.zip
Maximus_IV_Extreme-Z
ftp://ftp.asus.com.tw/pub/ASUS/mb/LG...-ASUS-0902.zip
MaximusIV-GENE-Z
ftp://ftp.asus.com.tw/pub/ASUS/mb/LG...-ASUS-0902.zip

Fix list basics are:
1) S3 resume with CPU PLL OV Enabled is patched - should work on most DRAM (cheaper ICs may have issues).
2) Ivy Bridge Support enabled.

thanks stasio

i wasnt aware of that problems with CPU PLL OV and S3
10-06-2011, 08:07 AM
stasio

Quote:

Originally Posted by andressergio

thanks stasio

i wasnt aware of that problems with CPU PLL OV and S3

Source:
http://hardforum.com//showthread.php?t=1578865&page=224
:D
10-06-2011, 01:54 PM
andressergio

Quote:

Originally Posted by stasio

Source:
http://hardforum.com//showthread.php?t=1578865&page=224
:D

thanks stasio i updated with no problems

cheers
Sergio
10-06-2011, 01:55 PM
andressergio

Quote:

Originally Posted by Timoleros

Hi guys!
I changed my UD4 with MIVE and i bought a new 2500K because my previous is dead (my previous was a X55 on UD4)
After a lot of tries i didn't make to boot in to windows desktop with more than X50 multi...
When i try to boot with more than X50 the system freezes at windows logo and the debug led shows AA..is there any chance to boot in the desktop or is a wall?

Thanks!

best thing u did is go to MIVE

now did u enable INTERNAL PLL ? if no do it
10-06-2011, 02:32 PM
Timoleros

Yes! MIVE is a great motherboard..

I enable INTERNAL PLL but nothing happens, exactly the same thing...with more than X50 the system freezes at windows logo and the debug led shows AA..
the only thing that i noticed with INTERNAL PLL enable is that the system is more stable at high frequencies...

Maybe is a bad chip... after 10 cpus this is the worst (the best was a x55 :rofl:)
10-06-2011, 03:23 PM
deachus

Yea, sounds like you hit your mutli wall if you have Internal PLL enabled.
10-06-2011, 03:59 PM
zsamz_

Quote:

Originally Posted by andressergio

best thing u did is go to MIVE

now did u enable INTERNAL PLL ? if no do it

the best think you did was listen to me n got the MIVE lol
10-06-2011, 05:42 PM
andressergio

Quote:

Originally Posted by zsamz_

the best think you did was listen to me n got the MIVE lol

lol
10-06-2011, 06:40 PM
xEnergie

Hi guys,

My system currently has a P8P67 Pro with the defective sata ports. I didn't get around to replacing it until last week when I emailed Asus and asked if I can upgrade while I do the replacement. Asus agreed to upgrade my board to the Maximus IV Extreme ( chose that over the Z68 as I do not need the functions of the Z68 ). Now I'm wondering which drivers do I need to install? I am already planning to cancel out the Bluetooth and was wondering if there's anything else I can cut back on? Saw the posts above and will be flashing to the 2001 bios as well.
10-07-2011, 06:35 AM
andressergio

Quote:

Originally Posted by xEnergie

Hi guys,

My system currently has a P8P67 Pro with the defective sata ports. I didn't get around to replacing it until last week when I emailed Asus and asked if I can upgrade while I do the replacement. Asus agreed to upgrade my board to the Maximus IV Extreme ( chose that over the Z68 as I do not need the functions of the Z68 ). Now I'm wondering which drivers do I need to install? I am already planning to cancel out the Bluetooth and was wondering if there's anything else I can cut back on? Saw the posts above and will be flashing to the 2001 bios as well.

u can use your actual install no problems at all

or

u can do a fresh install and put

latest chipset drivers from intel
MEI interface
intel SSD latest drivers

u can find all here

http://forums.tweaktown.com/gigabyte...ity-tools.html

cheers
Sergio
10-07-2011, 07:59 AM
MonsterDK

Hello folks :)

Just updated to 2001. Seems ok so far.

A few Q's for anyone who will kindly help :)

Q1: For a 2600k 4.8 OC what 'VRM Fixed Frequency Mode" is best to use?

Q2: Until I load the 'Extreme OC Profile'. There is nothing under 'Turbo Mode' with 'Maximum Power' ENABLED.
But with 'Extreme OC Profile' loaded there is a 1023.875 value in the 'CPU Core Current Limit'.
Should this be different for a 4.8Mhz OC? or just enabled and left on AUTO?

Thanks :)
10-07-2011, 09:53 AM
l0ud_sil3nc3

bios 2001 is looking pretty good

all of this was directly booted from the bios, no aisuiteII this time, vanilla XP Pro with appropriate tweaks and no wazza yet

1M
http://i.imgur.com/GTvwo.png

32M
http://i.imgur.com/AnQyN.png

I am having trouble submitting my spi score on hwbot, I keep getting an error but only when I try to submit my 1M result:shrug:
10-07-2011, 09:56 AM
l0ud_sil3nc3

also worth mentioning that I was able to boot 108 bclk directly in to Windows with this bios, without touching any skews, curious to try 3DMark2001 on it
10-07-2011, 10:43 AM
andressergio

Quote:

Originally Posted by l0ud_sil3nc3

also worth mentioning that I was able to boot 108 bclk directly in to Windows with this bios, without touching any skews, curious to try 3DMark2001 on it

nice buddy i didnt try yet on this bios but for 1850 needed skews for 108x52
10-07-2011, 12:48 PM
Martin.v.r

test whit x56 it can read win7 in, but it freezes at x57 on the desktop
http://img189.imageshack.us/img189/9162/superpi1ma.png

http://img838.imageshack.us/img838/4075/superpi32mj.png

may well be a one bios sets I have not been put Regt :rolleyes:
10-08-2011, 12:01 AM
M_T_M

What does the code 71 on the motherboard, because I have no pictures on the monitor?
10-08-2011, 01:54 AM
Martin.v.r

MTM
believe it is your mem, test them one at a time, in all your slots
10-08-2011, 04:34 PM
badatgames18

i don't like bios 2001, or maybe it's just my chip :(
blck clocking is more sporadic than it was on 1850... on 1850 when you reach max blck it was rock solid... you can turn it off and it will still be there.

on 2001.. skews behaved unpredictably... i tried booting 106.1 which was doable on my chip... it wouldn't, got frustrated, turned off computer for a few hours and bam.. booted to 106.1
http://hwbot.org/submission/2212611_

then i turn it off again... now it failed to overclock, and tried booting with 106.1 and it doesn't want to do it again
it feels like i'm on gigabyte again :shakes:

Show 100 post(s) from this thread on one page