Printable View
Hi there ;
thanks for your reply
I confirm the chip is ncp 5388
note : i tried the volt mod ((just like the sapphire card using the same voltage controller)) to the pin 19 (50 h vr) but this result in black screen , i tested the vgpu and found it was 0 . So the point was wrong . could u please check with me .
here the point market in blue.
http://www.xtupload.com/new/image-8E23_4A071EB9.jpg
You know that you probably killed your card?
That's why you always need to double/triple check. Just because a circuit looks like another one, or uses one identical chip doesn't mean that it is the same. Will have a thorough look at it when I find the time.
Edit: Measure resistance between pin#19 (Vfb) and pin#14 (AGND), with the system completely disconneced from the wall. Of course you can use alternate soldering points, that are direcly connected to these pins, but make sure that they really are.
Thanks for reply , i will measure the resistance later today when i get back home .
I have tried this mod since the author confirmed that it work on palit sonic video card same design as mine (check post #1164) , but the card was the HD 4850 sonic.
celemine1Gig thanks for your support :up: .
messured resistance between
pin 1 - 19 = 10.06 k
pin 14 -19 = 9.75 k
I would recommend either 2 200k potentiometers connected in series (resulting resistance of 400k), or alternatively a single 500k (or at least! a 200k) potentiometer. Keep in mind that the latter will have less precision in lower resistance (=higher voltage) ranges.
Anything less, concerning the total resistance, would give too much of a default voltage bump IMHO.
Set (all) the potentiometer(s) to their/its max. resistance and connect them/it bewteen pin#19 and pin#14. That should work. Maybe you got a black screen because you hit the OVP voltage limit. Then you could consider yourself lucky.
BTW: What the heck does that mean "50 h vr"?
And another thing:
I'm sorry, if this sounds rude, but do you even remotely know what you are doing?Quote:
Originally Posted by makaka
Why would you want to measure resistancee between pin#1 and pin#19, which correspond to "EN" and "Vfb"? What do you think has the "Enable" pin to do with the feedback in terms of a vmod.
Quote:
Originally Posted by NCP5388 datasheet
HI there ;
i will try with 2 x 200k or 500 k potentiometers ,
i meant 50 k potentiometersQuote:
BTW: What the heck does that mean "50 h vr"?
No i don't know :-) , i just saw a post above asking for the resistance between those so i measured it , may be it will be useful for u .Quote:
I'm sorry, if this sounds rude, but do you even remotely know what you are doing?
Also can i solder to other points since the pins are pretty hard for my low soldering skills ,
If yes please show them in the picture above .
Also were can i check the vcore , (i tried those)
http://www.xtupload.com/new/image-A092_4A083512.jpg
they show 1.28v 2d and 1.33v (3d) , note with video card turbo button on .
never checked with the normal mod:D
Try using the empty solder pads to the right, that would normally be occupied by some SMD capacitors. That's a better place to measure the real VGPU, because it is behind the inductors and not before them, like the points you marked.
And concerning VMem: One of the two AWP7065 probably regulates the memory voltage. Question's just which one (I would guess that it's the upper one). :) Some esaurements should clear that up.
HI there , Thanks for reply .Quote:
Originally Posted by celemine1Gig
The vmem is not required :D , the card can do 1100 stable .
Also can i solder (vgpu mod) to other points since the pins are pretty hard for my low soldering skills ,
If yes please show them in the picture above .
Of course you can use different solder points, as long as they are directly connected to the named pins. And I won't mark them as I can't test the electrical connection. You can do that. It really isn't very complicated.
thanks i will do it:up::up::up::up::up::up::up::up:Quote:
Originally Posted by celemine1Gig
HI there ;
After checking i found that the pin 14 is not directly connected to any other point . this is clear from the PCB pic ,
so even if not directly connected can i solder to it ?
pin14 probably "dives" into PCB where it's connected to GND. So You have to use some other GND point near that IC. celemine1Gig might know it better...
Thanks for reply , will any GND point work ?:confused: or it has to be near the IC , In theory any GND will work but go figure , this is why i am asking :DQuote:
Originally Posted by ceemic
Yep, normally any GND point should work. The best option would be to use a point directly connected to AGND, as this is the real reference for the feedback line, but as AGND and GND shouldn't differ by much (AGND should be less prone to interference), it should theoretically not matter at all if you used just GND instead. The difference between GND and AGND as reference should max. be in the mV range.
Thanks just done the Vmod :D , 1.48v and 900 mhz from the gpu stable :clap::clap::clap: (under water 40c load :D)Quote:
Originally Posted by celemine1Gig
Thanks again for your help
And now post a highres picture with your exact solder points, for other poeple with the same card, as reference. ;) I mean, I know how to work out mods, but others obviously don't, so this way you can give something back to the community.
Maybe you can even put all the needed info + pic in one final posting, so one can link to that one posting in case someone's gonna ask for the mod in the future.
will do it when i will get back homeQuote:
Originally Posted by celemine1Gig
First i want to thanks celemine1Gig and ceemic for their help finding the right vmod for the HD 4870 Palit soic edition (dual bios and dual fan) ,
here is the video card picture :
http://www.xtupload.com/new/image-0940_4A0ECCF9.jpg
The vmod for the card and the vcore measure points :
http://www.xtupload.com/new/thumb-96AB_4A0ECF14.jpg
http://www.xtupload.com/new/thumb-7D79_4A0ECF14.jpg
Here is some result using 2 Gb ram (470 mhz) , E8500 @ 4.2 Ghz (470x9) , p5q , 1000w psu , raid 0 :
Note : stock volt according to point above was 1.335 v (maybe palit over volted the card ). the card max stable was 800 mhz GPU and 1050 GDDR5
@ 1.44 v (load) 900 Mhz stable
http://www.xtupload.com/new/thumb-D714_4A0ED027.jpg
@ 1.44 v (load) 920 Mhz
http://www.xtupload.com/new/thumb-87D1_4A0ED089.jpg
@ 1.44 (load) 940 Mhz
http://www.xtupload.com/new/thumb-2D5A_4A0ED0D3.jpg
@1.5v (load) 950 Mhz
http://www.xtupload.com/new/thumb-BDD2_4A0ED114.jpg
@ 1.55v (load) 960 Mhz
http://www.xtupload.com/new/thumb-F347_4A0ED13A.jpg
@ 1.6v (load) XXX??? dark screen with restart GPU voltage show -0.03 v maybe a rest or OVP ,
975 also passed the test @ 1.55v but there was a lot of artifact , so i decided to not publish the result .
Any OVP mod for my card , i am looking for 1000 Mhz benchable
makaka, 960MHz is very good OC :)
Still need more , i looked for 1000 Mhz :D , any idea about OVPQuote:
Originally Posted by ceemic
The OVP mod would probably include cutting one trace. To decrease the 1.3V limit at pin#17 (DIFFOUT), one would have to increase resistance between Vfb (pin#19) and DIFFOUT, in order to decrease the voltage at diffout. Probably not worth the effort as ~1.6V is very high already. I'd rather say that perhaps some other mods. Better filtering VGPU could help get another extra MHz. Sometimes, voltage alone isn't really that helpful.
well what should be safe VGPU then for 24/7 usage under water , (40- 44 c load) ?
Is there a pencil vgpu mod for the XFX 4850? I've found the mod thread, but it only has the solder mod. TIA.
1.4 is pretty safe for 24/7 overclockQuote:
Originally Posted by makaka
more than 1.5 you will degrade the card :/
i killed one 4850 and one 4870 @ 1.5 ( core artifacts ) and the were at 35*C load
Hello
Is there a pencil vgpu mod for the Gigabyte 4850 512mb? Or soldering mod?
Here are the pictures http://i696.photobucket.com/albums/v...h_P5250409.jpg http://i696.photobucket.com/albums/v...h_P5250416.jpg http://i696.photobucket.com/albums/v...h_P5250417.jpg