so do these mods work on the non-deluxe too?
Printable View
so do these mods work on the non-deluxe too?
i got 2 15k vrs and 1 25k vr. i know one 25 and one 15 would do it for the cpu and ddr, but im not sure about the vdd. will the 15k be too much, too little, or just right for the vdd????
Woa there! You need 1 MEGA OHM, or 1000K Ohm resistor AND a 1 MEGA Ohm variable resitor. 25k aint gonna cut it!Quote:
Originally posted by utherwun
i got 2 15k vrs and 1 25k vr. i know one 25 and one 15 would do it for the cpu and ddr, but im not sure about the vdd. will the 15k be too much, too little, or just right for the vdd????
thats good to know :rolleyes:
guess i need to either go up to radio shack or peerless and then on to :stick:
thanks for telling me sys.
No prob ;)Quote:
Originally posted by utherwun
thats good to know :rolleyes:
guess i need to either go up to radio shack or peerless and then on to :stick:
thanks for telling me sys.
Just want to thank you guys for these Mods, they work great. :toast:
Thanks so much for all the info guys. I am gonna get all this stuff as soon as possible but I need to find a good online UK store that will ship all these goodies to me in Ireland.
Anyone know any good stores.
maplin.co.uk have a nice collection but I can't see any 25k resistors there.
?
RS Components sell em dude. www.rswww.comQuote:
Anyone know any good stores
Thanks for all the info to every1 mines up n running. VDD mod next. :|
http://homepages.nildram.co.uk/~noikz/DCP_1331.JPG
can I use two VR:s in the vmem mod? If I can then that would be great since i have two 10kohm VR:s here on my desk. Going to buy a 47kohm VR for vcore mod tommorow and I already have done my vdd mod.
yes you can, just remember that when you hook only one end to each other they will add, while you hook both ends they will be subtrate, can't remember but I think I'm right, but to make sure use a multimeter to make sure, don't want to kill the board, right? :DQuote:
Originally posted by blubbo
can I use two VR:s in the vmem mod? If I can then that would be great since i have two 10kohm VR:s here on my desk. Going to buy a 47kohm VR for vcore mod tommorow and I already have done my vdd mod.
Quote:
Originally posted by Mugen1516
so do these mods work on the non-deluxe too?
yes:D
Where I can read Vcore directly on board? (not by software);)
Thanks
bugs: I'm not sure, but you can just look in the bios...
I don´t like BIOS readings either...
My psu is giving 5V e 3,33V exactly and in BIOS there is 4,8V and 3,2V.
So I decided to meassure Vcore on the same IC and pin where the Vmod for Vcore is done, here...
http://www.maximumoc.com/img/hardwar...pu_labeled.jpg
And whit 1,8V choosen on BIOS, there was 1,79-1,80 V on my multimeter.
For Vdd I used this point for monitor...
http://www.maximumoc.com/img/hardwar...n8x/vddmod.jpg
And there was 1,55-1,56V
I just want to know if, when I done the Vmods, I can still read my voltages on the same points.
Thanks
Hmm well, I don't know about measuring the same pin. I would tell you if I had an A7N8X on me but I don't. Perhaps if someone else could check....
As for the same spot for the VDD, yes you still measure from there after the vmod. But I'm not sure bout the cpu.
Ok, thanks anyway.
Guess I should ho ahead with the Vmods, calculate depending on resistor wich Voltage should I get in those points, then measure and compare with BIOS readings.
Anyway if anybody knows a good Vcore reading point (pin), please post it here :toast:
Regards
No, not really :p. I'll just check with a multimeter. Thanks btw!Quote:
Originally posted by NUNEZ1980
yes you can, just remember that when you hook only one end to each other they will add, while you hook both ends they will be subtrate, can't remember but I think I'm right, but to make sure use a multimeter to make sure, don't want to kill the board, right? :D
Hi there,
Have done the vcore mod and all works great. But I have a problem…
When I Set FSB/Mult to 215X12.5 @ 1.95V - All looks good - Rock Solid. But when I move to 216X12.5 @ 2.0/2.1/2.2/2.3…V - Cannot get a good stable rig. I noted that when I go up that High (2+V’s) A> the fan connected to the Mobo CPU FAN Header slows down and the B> Core voltage drops when I start a CPU test.
– Is this a problem with my PSU? – using an Enermax 550WAT
– Is it the voltage of the mobo? – if so can I mod that to?
Can some one help me?
Do theise mods still work for the rev 2.00 A7N8X Deluxe's ???
Thanks :)
BLue078: Yepp, I can't see why not! Also roky has one :D
:cool: I'll round up some VR's tomarrow and give it a try.
I need more vdimm 2.8 sucks
Hi there,
Rev 2 works AOK on the VCORE - Have not done the Vdimm yet..
In relation to my previous post. It was indeed the PSU - it was not able to sustain a stable supply of current to the Mobo/CPU (Fans slow down - erratic V readings)
Replaced it with a Server class PSU (Enermax EG851AX-VH) last night... Initial test results are good - Brought the unit to a Vcore 2.06V - Rock solid and also as it happens got my best OC to date (12.5X217) rock solid .
Moral of the story – if you want to go with a High Vcore get a goooodddddd PSU
ROK
:) :)
hi,
i wona have 0,2V - 0,3V more v-core but i won't have a VR. can u tell me which resister i need?
hi, plz help me
whats the maximum and whats the minimum V-core u can get with the 25k VR ? with the bios settings 1,65 V