ASUS Rampage IV Extreme Owners Thread

Printable View

Show 100 post(s) from this thread on one page

12-07-2011, 03:54 AM
tistou77

Quote:

Originally Posted by Eldonko

Anyone else finding boot time is very slow on this board?

with the Intel drivers RSTe 3.0?

I have tested a R3E (X58 and ICH10R) and the boot time is longer than with drivers Intel RST 10.8

I thought it was because of the platform (X58), but with your feedback, it seems that it is also the same with the x79 :confused:
12-07-2011, 04:17 AM
pazza316

tistou 77 its the post time that is long not the Boot time. Post time is nothing to do with drivers and yes if you change the backplate which is included with the R4E you can use any 1366 cooler. Your EK block will fit perfectly with this backplate.
12-07-2011, 05:01 AM
tistou77

Quote:

Originally Posted by pazza316

tistou 77 its the post time that is long not the Boot time. Post time is nothing to do with drivers and yes if you change the backplate which is included with the R4E you can use any 1366 cooler. Your EK block will fit perfectly with this backplate.

ok thanks

anyone have screens of R4E (front and back) with a CPU WB "1366"
12-07-2011, 06:02 AM
pazza316

You dont need photos mate its the same. That block and mounting system work fine.
12-07-2011, 10:13 AM
UltraNEO*

Quote:

Originally Posted by LardArse

Init is skipped here, to save time and prevent long waits or timeout occurences with BT. if its really needed then an option may be made to select 'enable BT init'

OK.. Where this option? I don't see it anywhere. Maybe I'm just blind. ><
12-07-2011, 12:03 PM
Eldonko

Exactly, it is just holes, you can mount whatever you want. Im running Apogee XT w/ 1366 backplate.

Quote:

Originally Posted by pazza316

You dont need photos mate its the same. That block and mounting system work fine.
12-07-2011, 04:05 PM
Boulard83

For those who want to WC the motherboard.

http://www.koolance.com/water-coolin...roduct_id=1227

http://www.koolance.com/water-coolin...b-asr4e_p0.jpg

http://www.koolance.com/water-coolin...mb-as4e_p2.jpg
12-07-2011, 05:08 PM
mdzcpa

Although I wasn't to worried at all about the boot time (post time) myself, I decided to disable the BT and unused ASMedia controller (as suggested above), and my boot time is greatly reduced. Warm boots fly by in a matter of seconds, and the cold boot time is cut nearly in half. Also disabling non-bootable drives under the Boot menu helps. Something to look into for those not using these onboard devices and wanting to speed up the boot time.
12-08-2011, 07:42 AM
Levesque

/Sarcastic mode on.

Jack: "Hey Bob, let's do a high-end motherboard for Quad-SLI, but let's change the usual molex EZ-plug we usually put on those motherboards to a 6-pins PCIe connector, so no one will be able to use it, since all the high-end PSUs on the market only have 8 PCIe cables max. Let's make a Quad-SLI motherboard, but be sure that no one can't use it without the proper adaptor, since they will only have 8 PCIe cables, but will need 9!''

Bob: ''Ok, great idea! So we will be sure that they will go crazy trying to find a stupid 2 Molex to 6-pins PCIe that no one is making anymore! Or wait 2 weeks to get one with the great couriers out there. And be sure NOT to put one of those 0.99$ connectors in the motherboard box, and let's put alot of useless junk with it instead!''
12-08-2011, 11:06 AM
Cookiesowns

Quote:

Originally Posted by Levesque

/Sarcastic mode on.

Jack: "Hey Bob, let's do a high-end motherboard for Quad-SLI, but let's change the usual molex EZ-plug we usually put on those motherboards to a 6-pins PCIe connector, so no one will be able to use it, since all the high-end PSUs on the market only have 8 PCIe cables max. Let's make a Quad-SLI motherboard, but be sure that no one can't use it without the proper adaptor, since they will only have 8 PCIe cables, but will need 9!''

Bob: ''Ok, great idea! So we will be sure that they will go crazy trying to find a stupid 2 Molex to 6-pins PCIe that no one is making anymore! Or wait 2 weeks to get one with the great couriers out there. And be sure NOT to put one of those 0.99$ connectors in the motherboard box, and let's put alot of useless junk with it instead!''

LMFAO! Although I think for their logic is that, most people that will be running quad fire will be using 2 PSU's or have the necessary cables and what not to take advantage of that 6 pin power. All in all, this is a board designed for extreme benchers as well as top enthusiasts. If not why not just get the Formula, apart from the lack of 8 DIMM's
12-08-2011, 01:31 PM
Eldonko

You mean the molex to 6 pin that is $3 at any computer store? Who is going to bench 4x 580 with 1 PSU anyway? Seems like you are grasping at straws for something to complain about..
12-08-2011, 01:43 PM
Nightprowler_77

Anyone testet the x-socket ?
12-08-2011, 01:59 PM
pazza316

Yes. The change of socket works fine. I have tested it with Koolance 370 waterblock and 1366 backplate.
12-08-2011, 02:05 PM
Eldonko

Yep, have a look here: http://www.hardwarecanucks.com/forum...review-10.html

Pretty much anything 1366 that has a backplate will be fine.

Quote:

Originally Posted by Nightprowler_77

Anyone testet the x-socket ?
12-08-2011, 02:17 PM
Nightprowler_77

Thank you. :)

So my EK-Supreme HF should work just fine then?
12-08-2011, 02:20 PM
hokiealumnus

Quote:

Originally Posted by Nightprowler_77

Thank you. :)

So my EK-Supreme HF should work just fine then?

If you have the original (old, somewhat pain in the rear) mounting system, the four screws' threading fits the SKT2011 mounting system perfectly.
12-08-2011, 02:47 PM
tistou77

About the OC, are different Vcore (offset)?

there is a delta Vcore/vscca? (as 1366 and Vdimm/vQPI)

compared to 1366, the OC is different?

thanks :)
12-09-2011, 05:50 AM
Levesque

Quote:

Originally Posted by Eldonko

You mean the molex to 6 pin that is $3 at any computer store? Who is going to bench 4x 580 with 1 PSU anyway? Seems like you are grasping at straws for something to complain about..

When you live up north of the 49th parallel, already under 3 feet of snow, with the nearest computer stores at 8 hours from my place... finding a stupid adaptor like that can be annoying. B.O. everywhere I ordered it in Canada. 3 are stucked at the US/Canada border for 3 weeks now (Christmas time...), coming from USA stores. And I fried 2 PSUs trying to use dual-PSU.

Call me stupid, noob, etc I don't care, but after getting 1 dead AX1200 and 1 DOA HCP-1200, I'm grasping at straws now, yes. :) They could have put that 3$ adapter in the box.

And for Quad-Fire 4X6970 Lightnings, I don't need to use a dual-PSU set-up. A single HCP-1200 is plenty enough. But only 8 PCIe cables. Need 9. :(
12-09-2011, 07:11 AM
Photek

I think my board has just died for no reason.... was playing a game and it suddenly goes off, not even BSOD, just off. Now when i turn it on, the board LED lights stay off including the error codes, everything else stays off (no fans come on apart from the fan on the board itself) theres no post screen or any kind of activity. Only things that work on the board are the lights for the power and reset buttons. When i press the power button only the boards fan spins, nothing else at all.
Tried ressetting CMOS and removing the battery on the board but that dont help.

What else could i do? I'm about to try my PSU, cards and memory in another board, to make sure they're ok, but it's looking like it's the board itself. Even if the CPU was dead (which i very much doubt because it was only at 4.4GHz at the time and temps were well well 60c) the board would still show activity on the lights and the error code would display.
12-09-2011, 07:43 AM
Splave

pop out the battery tear it down and remount your cpu in the socket, then try it again.
12-09-2011, 07:54 AM
Photek

Seems that it's the PSU...

I connected it to another board... same thing happens. Well thats kind of a releif i suppose :mad: any recommendations for a new PSU? It needs to be beefy, like around 1200w preferably. The one thats just died was a Thermaltake toughpower 1200w... what a POS!
12-09-2011, 11:07 AM
Cookiesowns

Quote:

Originally Posted by Photek

Seems that it's the PSU...

I connected it to another board... same thing happens. Well thats kind of a releif i suppose :mad: any recommendations for a new PSU? It needs to be beefy, like around 1200w preferably. The one thats just died was a Thermaltake toughpower 1200w... what a POS!

LOL! thermaltake PSU's, they've been known to alot of people to avoid. That being said, the AX1200w fits most peoples bill quite well, I personally run that myself. Or if you can, get your hands on the SeaSonic 1000W 80+ platinum, great voltage regulation on that psu, given that you also have some sort of power conditioner as the ripple suppression isn't as great compared to the AX1200.
12-09-2011, 05:10 PM
OC Nub

Playing around with max oc, this is about all I am able to do on water. I guess it will need cold to go any higher.

Ill try with turbov evo later and see if it can go higher in windows.

http://i43.tinypic.com/t7lgu8.jpg

http://valid.canardpc.com/show_oc.php?id=2140528
12-09-2011, 05:40 PM
owikh84

I have problem loading memtweakit it just minimize into my taskbar.
btw, I'm on win7 x64, bios 0901

@ OC Nub
nice! yep i believe it need some cold to go higher... my 3930K can post at 55X but will stuck at win logon
12-09-2011, 06:03 PM
OC Nub

Thanks.

Havent used memtweakit, but it seems to open ok here.

Anything above this freq. hangs at windows login. Maybe software can get it higher.

Show 100 post(s) from this thread on one page

***ASUS Rampage IV Extreme Owners Thread***

ASUS Rampage IV Extreme Owners Thread