Mountain Mod Ascension "MMA"

Printable View

Show 100 post(s) from this thread on one page

06-23-2010, 06:32 PM
marxviper

Quote:

Originally Posted by Kibbler

Leave everything in a well ventilated place for about 2 days. Should be fine.

Thanks for your reply. I'll do that.

Even After tightening the screw the motherboard block is still leaking.

How should I fix it?
06-23-2010, 07:32 PM
marxviper

Update:

I did tight the screws. Unfortunately, some screws, well what you could say, can't be open. The hex key doesn't have tight grip in them anymore.

I have two choice. Put super glue around the joints and leak test it again or solder it :rofl: and leak test it.

What do you guys recommend? I don't think anyone had similar problem like mine.

Last choice is buy a new motherblock which I don't what to as I can't wait for it
06-23-2010, 10:58 PM
Utnorris

Quote:

Originally Posted by marxviper

I tried this site before. Unfortunately they don't ship internationally.

I have an update.

Watercooling Pros in XS! I need your help big time. I have leak on motherboard block. It leaked at the place where I replace red plexi piece with the transparent one. There was an advice not to overly tight the screw as there is chance to break te plexi. Well! I didn't tight them enough just to precaution and now de iodized water is on the board. I used kitchen towels to absorb as much water as I can. Now as beginner, I have no clue what to do next. Surely, motherboard wasn't on. Only te pump. Any step by step advice would be appreciated.

Pull the bridge off and make sure the rubber o ring is seated correctly. Sometimes the o ring gets caught between the plexi parts and will get smashed and deformed. Just pull it apart and redo it and you should be fine. Next time you have a leak use toilet paper, soaks up water like a sponge.
06-24-2010, 12:30 AM
marxviper

Quote:

Originally Posted by Utnorris

Pull the bridge off and make sure the rubber o ring is seated correctly. Sometimes the o ring gets caught between the plexi parts and will get smashed and deformed. Just pull it apart and redo it and you should be fine. Next time you have a leak use toilet paper, soaks up water like a sponge.

Well I tried removing the bridge. The screws are messed up right now. I can't even unscrew it anymore.
06-24-2010, 01:21 PM
marxviper

I tried glue and a difference. But wasn't hundred percent.

Now I'm using powerful silicone sealant to do the trick. Need to leave it for 24 hours.

Tomorrow will be another leak test.

If all fails, need to order a new block. Hope Ek would send me one without red bridge attached just like in the picture on their site. :)
06-24-2010, 01:24 PM
marxviper

I tried glue and a difference. But wasn't hundred percent.

Now I'm using powerful silicone sealant to do the trick. Need to leave it for 24 hours.

Tomorrow will be another leak test. Hope it works.

If all fails, then I need to order a new block. Hope Ek would send me one without red bridge attached just like in the picture on their site. :rolleyes:
06-25-2010, 10:52 AM
marxviper

What's the optimal time to test the leak?

I just started the test. Till now no leak. :Phew:
06-25-2010, 11:12 AM
Polizei

If you used the proper size allen key to remove the screws, they wouldn't be "all messed up" and you could remove the bridge.
06-25-2010, 11:14 AM
randomhro

It's still possible to strip the screws with the proper sized Allen wrench. If you don't have it inserted all the way into the screw it is quite easy to strip a screw, but that usually happens from not paying attention while trying to do it.

A minimum of 24 hours seems to be the norm for leak testing before actually applying power to components.
06-25-2010, 11:53 AM
marxviper

Quote:

Originally Posted by randomhro

It's still possible to strip the screws with the proper sized Allen wrench. If you don't have it inserted all the way into the screw it is quite easy to strip a screw, but that usually happens from not paying attention while trying to do it.

A minimum of 24 hours seems to be the norm for leak testing before actually applying power to components.

I agree with you regarding wearing of the screws. I did use proper keys.

I will leave the old block with the water running. See how things go.
06-26-2010, 05:15 AM
marxviper

Unfortunately, things didn't go as planned.

Waiting for new motherboard waterblock to arrive from the store. Until then :shrug:

Don't worry this setback didn't stop me going watercooling. I'll definitely be back for more watercooling in near future.
06-27-2010, 04:26 PM
marxviper

How do attach multiple RAM on RAM waterblock?

Do you take all the fins out and attach the RAMs on the motherboard and then add the block on the top?

It might be hard to estimate the distance between the RAMs perfectly without the above procedure.

What do you recommend?
06-28-2010, 02:08 AM
Alexandr0s

Well, I believe with MIPS blocks you can first install the single modules (the two plates touching the RAM), and then put the waterblock on top.

How to mount it can be found on their site, but it's in German, so I used Google Translate to translate it:

1st Loosen screw (not complete) of 3 middle screws Alumodules.
2nd WLP apply to the storage module.
3rd Inserting the memory modules and tightening the screws compress the three middle Alukühlrippen.
4th Check whether the memory module in Alumodul tight bind.
5th Process corresponding to the number of the memory modules again.
6th RAM modules installed now in the memory slots on the motherboard and secure it.
7th WLP apply to the contact surfaces of the Alumodule.
8th Screw the RAM modules with the main body of the RAM cooler 3
06-29-2010, 04:16 AM
malkiewicz

Quote:

Originally Posted by marxviper

Unfortunately, things didn't go as planned.

Waiting for new motherboard waterblock to arrive from the store. Until then :shrug:

Don't worry this setback didn't stop me going watercooling. I'll definitely be back for more watercooling in near future.

What are you going to do with the old block.... You could send it to me.......:)
06-29-2010, 04:48 AM
marxviper

Quote:

Originally Posted by malkiewicz

What are you going to do with the old block.... You could send it to me.......:)

I don't mind. Send me your address in private message and it will be send by Friday.
06-29-2010, 05:23 AM
malkiewicz

Thanks.... PM sent
06-29-2010, 05:56 AM
marxviper

Quote:

Originally Posted by malkiewicz

Thanks.... PM sent

No worries. You are welcome.

If you are able to fix it, I'll be glad. Do you want me to send you pictures of it?

Update:
Got block today. It still has the red bridge and this time they forgot to send the other bridge. (heart break)
06-29-2010, 05:59 AM
marxviper

By the way, should I place new thermal pads on the motherboard? I left the old ones on it for days without block attached to it.
06-29-2010, 06:04 AM
malkiewicz

Quote:

Originally Posted by marxviper

No worries. You are welcome.

If you are able to fix it, I'll be glad. Do you want me to send you pictures of it?

Update:
Got block today. It still has the red bridge and this time they forgot to send the other bridge. (heart break)

Thanks agian,

No pictures required…. I’ll let you know if it’s fixable….

Sorry to hear about your misfortune…. Have you contacted them to see if they will send you the part you need?

Note: the old ones should be fine as long as they haven’t been compromised or compressed too much... If you’re worried about your thermal protection I would replace them just to be safe….
06-29-2010, 08:37 AM
marxviper

Quote:

Originally Posted by malkiewicz

Thanks agian,

No pictures required…. I’ll let you know if it’s fixable….

Sorry to hear about your misfortune…. Have you contacted them to see if they will send you the part you need?

Note: the old ones should be fine as long as they haven’t been compromised or compressed too much... If you’re worried about your thermal protection I would replace them just to be safe….

To be honest, the computer currently I'm working is the only computer I have and :rofl: I can't wait any longer. I'm addicted to computers.I already attached the block to motherboard.

When I do another worklog, I'll take my sweet time.

Currently, I can't wait and get this thing running.

I have put LED lights on the blocks but can't find a way on gtx480. Hope I find some solution on it.
06-29-2010, 12:12 PM
marxviper

Quote:

Originally Posted by malkiewicz

Thanks.... PM sent

Pm replied.
07-01-2010, 04:25 PM
marxviper

I just finishing the work on my computer.

The idle temp @ 2.6GHz is 19 C. My windows are open. The temperature in dublin is 15 according to yahoo.com.

Fans are running at half speed.

Pictures will be upload tomorrow (friday)
07-02-2010, 03:16 AM
marxviper

first batch of pictures:

http://i919.photobucket.com/albums/a...0001129NEF.jpg

http://i919.photobucket.com/albums/a...0001133NEF.jpg

You could see the scratch on the rads. Initially, I had a place the drives bays to be at the top but the screws at the floor caused me problem and it couldnt fit. So I decided to put bays at the bottom and tubes coming out from the top, being careful if the the rad got punctured it would leak from the bottom.

http://i919.photobucket.com/albums/a...0001135NEF.jpg

http://i919.photobucket.com/albums/a...0001136NEF.jpg

http://i919.photobucket.com/albums/a...0001137NEF.jpg

http://i919.photobucket.com/albums/a...0001139NEF.jpg

http://i919.photobucket.com/albums/a...0001140NEF.jpg

http://i919.photobucket.com/albums/a...0001142NEF.jpg

http://i919.photobucket.com/albums/a...0001144NEF.jpg

I have loads of pictures coming up, it takes time to fix them and upload them. Hope you understand
07-02-2010, 04:19 AM
malkiewicz

I can’t wait to see this build completed…. Nice Job… :up:
07-02-2010, 04:20 AM
marxviper

Quote:

Originally Posted by malkiewicz

I can’t wait to see this build completed…. Nice Job… :up:

thanks

It is completed thats why you see me uploading the photos ;)

Show 100 post(s) from this thread on one page

All times are GMT -8. The time now is 01:03 PM.

XtremeSystems