Printable View
I'll but the sticks aint the problems, it's a bios/cpu/something issue, what started happening to me at 1st 5.1Ghz shotsQuote:
Originally Posted by coolhandluke41
vCore around 1.4v when loaded
http://img842.imageshack.us/img842/2139/51002.jpg
and what happens now at 5.2Ghz if I keep the mem timings I was using
1866 10-11-10-28 1T
http://img696.imageshack.us/img696/1417/bahs.jpg
At 5.0Ghz nothing of this will happen, it'll run just OK.
Is the system stable at those settings? I've had no luck with Extreme LLC and entering manually the offset. However, it works fine with LLC disabled and offset > auto.Quote:
Originally Posted by st0ned
Sandy Bell 2600K.
Batch L041B200
Cooling AIR scytne Ninja first model.
Workin same time: memtest+linX+Prime 95 small ff....
http://i55.tinypic.com/34jexzr.jpg
http://i51.tinypic.com/16beb2e.jpg
http://i55.tinypic.com/mj8wer.jpg
http://i56.tinypic.com/2mg1t7k.jpg
http://i52.tinypic.com/bdpj76.jpg
http://i51.tinypic.com/d5jpc.jpg
http://i56.tinypic.com/261k950.jpg
Greetings from Finland
Batch# L040B165 :D
@stoned Try to increase IO volt first and when you cap out IO, try to increase SA volt. Because I think your mem controller needs more juice to be stable.
How much and untill what volts would it be safe...Quote:
Originally Posted by deaffob
I havent installed mine yet, but is there any way of finding the stepping? Or do i need cpuz..?
That looks good, and it's the same Batch# and MB as mine.:)Quote:
Originally Posted by Mace
I haven't pushed that much voltage yet, just settled with 4.5GHz 1.27v for now, while I'm following laboratory rabbits, LOL, but it's good to see it can breach the 5.2GHz with that voltage.
Some Prime action with my new L042B076, not bad :yepp:,
http://img510.imageshack.us/img510/1...k46hton.th.jpg
Cpu-z mate, All retail chips are d2's also :up:Quote:
Originally Posted by chestnut
Had to wait 2 weeks in the UK for anywhere to really start getting the 2500k in stock, but mine arrives monday and will be running with a lapped Hyper 212+ strapped to its back. Can't wait to see how far it will go, hoping for between 4.8-5GHz with about 1.38v :D
Dami3n what you gonna do with your Gulfy!? :DQuote:
Originally Posted by Dami3n
Sold. No difference in games and better temps in my little case, so was a easy decision :DQuote:
Originally Posted by kpablo
Goodluck with that, i've only seem a few which are golden chips.. best ive seen is 1.35 @ 5ghz :DQuote:
Originally Posted by Ket
Ahhh i read this thread and willing to sell my 2600K to find some good batch
Really nice OCs. My 2600k is rock-stable with this:
http://i1139.photobucket.com/albums/...g?t=1296333147
and the question. I catch 33C at idle with Corsair H50. is it normal?:confused: At load I no way pass over 56C (at defaults). Mobo is Asus P8P67 Deluxe
thx in advance
@mythsquare .. Temps seem about right, What are your ambient temps??
@Johnny87au
Case stands near the heating so I think it's 22+ C around it
Thing that you should notice is I'm running it with H2O but even if water temp rises near +30°C it's stable at 5.05GHz 1.36V :p:Quote:
Originally Posted by Sam_oslo
Water is not essential any longer, SB runs really cool on high-en air.:p:Quote:
Originally Posted by Mace
I've never pushed the vCore that far, just waiting out and watching laboratory rabbits, until we know more how resilient these chips are over time, as said before, but that @5GHz 1.36v sounds really good and could tempt me to try it soon.
My PRECIOUS!
http://i55.tinypic.com/34gjy9x.jpg
http://i54.tinypic.com/2ilg7c9.jpg
http://i53.tinypic.com/2zeza4y.jpg
with 24/7 settings:
CPU testing:
http://i52.tinypic.com/2euj1jb.jpg
http://i55.tinypic.com/5f26j5.jpg
Memory testing:
http://i52.tinypic.com/153xykz.jpg
http://i56.tinypic.com/rkanph.jpg
Benching settings:
http://i51.tinypic.com/2mh7on5.jpg
http://i55.tinypic.com/2en1coz.jpg
http://i52.tinypic.com/t8nqmh.jpg
Movies during bios settings and booting +3DMark 2006 full@ default setiings on videocard:
http://www.youtube.com/watch?v=c1rSKb6wgeI
http://www.youtube.com/watch?v=IMWAClNWv68
Nice one DJ, I can get a L041B204, not far from yours, worth a try you think?
:up:
SURE, I've seen that batch on xtremesystems, not remember where, seems to be a little better than mine at above 5,2+ Ghz (a little less milivolts on Vcore, for same freq) or cpuz calibration difference...
No mater, I hoped to pick up an cpu for 4500 Mhz around 1,33 Vcore (that was my expectation) but those is very very good, 4700 Mhz 1,259 on bios and 1,26 1,275 on load.
Grab it as is it available! :toast:
sweet, my D1 ES does 4500 at 1.25v, I was happy with that but it craps out at 4950 flat out so Im hoping this next cpu will only get better.
:up:
Stop talkin' ,and GRAB that L041B204 biatch! (beast) :clap::up:
I also think that L042B076 it's a go for it!
My 1st L042B076
5.0Ghz with 1.424v not bad :P
http://img830.imageshack.us/img830/9787/5000933.jpg
But the 2nd one is the best:
1.424v set on bios ( vCore jumping from 1.416~1.432v )
http://img535.imageshack.us/img535/373/510025.jpg
much lower GFlops on the 2nd.
800 vs 933 mem freq vs Linx in 4threads vs Linx in 8threads.Quote:
Originally Posted by wekktor
Motherboard Gigabyte GA-P67A-UD7
RAM Speed : 1071.3 MHz (1:8) @ 7-7-7-20 (2144MHz)
http://valid.canardpc.com/cache/screenshot/1628075.png
Validated by CPU-Z 1.56.2
:D
WPrime 1024 mil stable.
http://img163.imageshack.us/img163/3...0109225256.png
Nice result is it prime stable!Quote:
Originally Posted by 1Day
I'm impressed.:up:Quote:
Originally Posted by 1Day
This is not mine but it deserves some attention:
http://s43.radikal.ru/i102/1101/58/15ccc7572213.jpg
DIGI+ VRM
Load-line Calibration - High
VRM Frequency - Manual
VRM Fixed Frequency Mode - 480
Phase Control - Extreme
Duty Control - Extreme
CPU Current Capability - 140%
CPU Voltage - Manual Mode
CPU Manual Voltage - 1.38
DRAM Voltage - 1.65 (depends om memory
VCCSA Voltage - Auto
VCCIO Voltage - 1.05
CPU PLL Voltage - 1.90
PCH Voltage - 1.05
CPU Spread Spectrum - Disabled
CPU Power Management
CPU Ratio - Auto
Enhanced Intel SpeedStep Technology - Enabled
Turbo Mode - Enabled
Turbo Ratio - Maximum Turbo Ratio settings in OS
Maximum Turbo Ratio settings in OS - 50
Turbo Mode Parameters
All Auto
Advanced/CPU Configuration
CPU Ratio - Auto
Intel Adaptive Thermal Monitor - Disabled
Active Processor Cores - All
Limit CPUID Maximum - Disabled
Execut Disable Bit - Enabled
Intel Virtualization Technology - Disabled
Enhanced Intel SpeedStep Technology - Enabled
Turbo Mode - Enabled
CPU C1E - Disabled
CPU C3 Report - Disabled
CPU C6 Report - Disabled
Mobo Asus P8P67PRO
2x2ГБ DDR3 Kingston Hyper X KHX2133C9AD3T1K2/4GX (PC17000, 2133МГц, CL9)
very nice 1Day !, batch# ?
hey stoned is your EPU disabled ?Quote:
Originally Posted by st0ned
That's the overcurrent protection right ? I'm not sure, why ?Quote:
Originally Posted by coolhandluke41
:D As you know I do not do stable. :yepp:Quote:
Originally Posted by bro20000
If I can bench at those frequencies then that is all I ask from a CPU. Stable as in prime95 or what ever the current flavour of the month is has no relevance for my needs.
I do think it is important to those whom it matters to.
In many ways I sort of see it like a kind of benching but instead of points for scores it is how long at what frequency. So I respect those who practice stability testing but it is not what I am into. :)
5.7 for wprime 1024 is very nice :up: What batch chips you have ?
:up::)Batch FTW ???? and what cooling u use ln2 not air i think... do u run any superpi 1M or 32MQuote:
Originally Posted by 1Day
I booted into OS at 5.7GHz on air. But to bench Wprime and Super Pi 32 I have used water. My husband bought me a SS yesterday so that is what I will use in the future.Quote:
Originally Posted by PytonOrm
Re Batch : L040B307
:yepp:Nice same batch has mine! I will try for 3.7 to when my new hardware comes!Quote:
Originally Posted by 1Day
nice work. did you use a 56x multi or a lower multi and bclk?Quote:
Originally Posted by 1Day
57x Multi. And to be brutally honest it was very little my work and all the CPU.Quote:
Originally Posted by jackbrennan2008
http://img717.imageshack.us/img717/6698/cpus.png
I got these on Friday. :p:
My first one had a wall at 5.4GHz so :shakes:
1Day
:up: Awesome work !!! nice only 4 pcs of 2600K thats nuts :woot:
1day - awesome cpu, is that the highest ever for a 2600K ?
st0ned - very nice , hit them for max clocks please.
Guys do we have a discussion here on what rams to get for these?
:up:
Quote:
Originally Posted by aussie-revhead
No there are six others that have clocked higher. :) Not sure if they clocked with HT on and all cores enabled like I do. But higher they have clocked. I bench so I am not really going to get any HWBOT points for CPU-z with a Sandybridge. Not when 8GHz plus is what you have to beat.
Ram is a difficult one. I have had amazing results (better than expected) with some Giel Evo Two sticks I bought for the P55 boards last year. 2000MHz Cas6 - 9 - 6 doing 2133 at Cas 6 with ease. The only discussion I saw was working out why Hypers are not clocking on the SB boards. But with my GA-P57A-UD7 board I have not had any hassle as you can see with Hypers. I wonder if it is board related. You know how the bios sets the latencies of the ram. But I have no real idea.
I meant is that the highest multi for a 2600K.
The faster ones on hwbot are not far ahead of yours, good work. Only one of those 6 is on 57x multi too.
http://www.hwbot.org/searchResults.d...peId=&offset=0
:up:
Good job 1Day, :up: keep doing what you do best :)
Running on air cooling Venomous X 2 fans.
i7-2600k Batch L041C108.
Asus P8P67 motherboard.
5ghz LinX takes 1.4-1.41v to be stable but hits 89C!
So for 24/7 use I'm gonna stick to 4.9ghz 1.36v set in bios:
http://i246.photobucket.com/albums/g...9/Capture3.jpg
Nice Laguna, try benching at higher clocks without LinX torture? It would be good to see its highest possible multi.
:)
Yeah my venemous-X with just one fan gets up to 90C in small FFT prime, with 5 ghz and 1.45v load going through the thing.
And TRUE black with Ven-X mount fares even worse, even though the mount is so secure with the TRUE that it doesn't swivel one bit...(the Ven-X swivels but temps are lower).
Even a 190cfm Delta won't help, because it reaches 80C within 5 seconds...
Im on water and with the volts up it cooks fast anyway so Im not sure how much the water cooling is helping but at least its quiet. It works well at sane gaming clocks.... but its more often pushing for max.
:)
@ 1day great results mate, u and bro 20000 have one of the best batches on this forum, seems like the UD7 is somewhat limited im mem frequency with hypers past 2133... ASUS maximus doesnt have these issues, Maby they fixed it with a bios update???
@aussie-revhead, if u check the xtremeoverclocking section Criminal is aiming for 57x and 58x :D
has anyone done 58x yet? Is it possible? What limits the max multi on these?
:)
It was a toss up between the Venomous X and the Megahalems but I don't think the Megahalems would have been much better given how the i7-2600k really heats up quick with 8 threads.Quote:
Originally Posted by Falkentyne
Yeah I'm good at 4.9ghz and less than 1.4v vcore and 80c load for 24/7 is good enuf for me :up:
AFAIK nope, still waiting for results on SS phase..
Quote:
Originally Posted by Johnny87au
every time i turn the PC on i am aiming for 6Ghz but my chip only wants to go 5.2Ghz hahaha
If you try 58x you could kill your CPU. A guy at hwbot complained his chip died after trying.Quote:
Originally Posted by aussie-revhead
Well that is true but i've seen some things on this forum i thought i would never seen, mission impossible :rofl:Quote:
Originally Posted by dinos22
LOL! I'm famous!
http://cgi.ebay.com/NEW-INTEL-CORE-i...#ht_6448wt_948
I gave the guy permission to use my screenshot since he sold me a decent chip.
Not magical like L042 magical, but a decent chip.
I think this is his last L041C108 i7-2600k =)
I have two CPUs of different batch and they both OC the same, so I'm narrowing it down to my board. Gotta get rid of this board and get the Maximus IV Extreme when it's available. You can wait until forever, but EVGA is late to the game so I'm ditching them. Think EVGA might be going the way of BFG, soon.
I did some more testing this weekend. And Prime 95 does not stress SB enough (Custom 960k).
It was more then 2 hour prime stable when i stopped it. But within 15 min of playing Starcraf 2 i got a crash.
So i stress tested it with 6 threads of prime and while playing SC2. 90-98% CPU load. I needed 0,05v more to get it stable again. I'm now at 4.7 GHz 1.35v bios (1.38-1.39v load)
Why did he hide the Batch/FPO # from the picture? Not that I don't trust him, but that makes it suspicious.Quote:
Originally Posted by LagunaX
I'm so proud of my new shiny Corsair A70, the last time I bought hsf was TT Big Typhon:D
Too bad all 5 2600ks clocked @ 5.3 Max:(
L042B208 53X
L042B291 52X
L045A998 52X
L037B224 52X
L042B243 53X
http://img573.imageshack.us/img573/2...nshot010jc.jpg
Cant set more than x57 on my UD5 but you can bclk it up & go past 5.7GHz :DQuote:
Originally Posted by overcrash
Well it was not really dead. But he could not run more then one core stable. It was badly dammaged.Quote:
Originally Posted by overcrash
Maybe a bios issue?Quote:
Originally Posted by Dumo
Could be. I tried with Biostar TP67 and Asus P67 Pro, air and ss with latest biosesQuote:
Originally Posted by Astennu
Every time I doesnt believe 5 GHz with my aircooled AMD validation and one day (Friday), I got it :). So, give it time, maybe...;):DQuote:
Originally Posted by dinos22
http://1.2.3.11/bmi/valid.canardpc.c...ot/1624177.png
http://valid.canardpc.com/show_oc.php?id=1624177
He didnt damage the cpu cause of the multiplier,he damaged it because she single stage stopped working and the temperature was sky-high :DQuote:
Originally Posted by Astennu
Those 2600k C-batches are really rare, and probably a better one. It will be interesting to see one in real action.Quote:
Originally Posted by LagunaX
Good to see 2600k C-batch in action. I've been waiting to see one of these, but they are really rare.Quote:
Originally Posted by LagunaX
Aha thats not what it said on HWBot. That makes sense. I found it strange that it would get damaged by a 58 multi.Quote:
Originally Posted by Alex-Ro
Soowy for double-post,
The forum seams to be acting strange. I was sure I posted the second one in another Thread. I couldn't delete it either, anyways it wasn't the meaning to double-post.
It may just be be the chip samples... finding a strong 2600K is not easy.Quote:
Originally Posted by Dumo
I'm still searching for a really good 2600K but I did find a 2500K that can bench x55 with my Biostar TP67XE on air.
http://www.xtremesystems.org/forums/...0&postcount=50
http://www.overclockers.com/forums/s...1&postcount=91
Not sure how impressive this is compared to others here...
Just was playing around over the weekend and hit the following:
4.3GHz stable (43x100)
EPU on, all power saving on
vcore offset: -.075
stock cooler
Setup:
P8P67 PRO
2500K
Seasonic Fanless 400W
Crappy G.Skill 4GBx2 1333MHz ram
It's nice that Intel can do 4GHz+ on stock cooler nowadays :)
Just be careful what aftermarket air cooler you pick because not all will fit on the Asus P8P67 boards due to the high rise heatsinks.
A Titan Fenrir, for example, will not fit due to the retention bracket (I tried)...
Thermalright, Prolimatech, Cogage, and a couple of others fit ok though...
That sucks mate, perhaps Ill sell you mine when I get finished with it :up:
http://images.hardwarecanucks.com/im.../OC/cpuz-9.png
Quote:
Originally Posted by Dumo
Nice:up:Quote:
Originally Posted by Eldonko
I'm still having fun play Eeny, meeny, miny, moe at local Micro Center....try to pick up a 2600K:D The latest batch is L050XXX which will be my next try
Very nice chip there Eldonko, what batch?
L040b165
What cooling and what temps do you get at 1.6v? Mine sizzles at 1.55.
Cheers.
Single stage, -45 is as warm as it gets.
Yup that would certainly do it. Nice chip.
Still got over 5700 on water, sub zero really doesnt do much w/ these chips, 50-75Mhz if you are lucky.
I said I didn't need a 2600k..... but my 2500k needs 1.4V for 4.8ghz, lol, so I went to MC and bought a 2600k. How does the L042B208 batch clock?
just got a L045B005 1138 from tiger direct, not much info about it?
Finalized my OC. L042B291 4.8ghz@1.37v Linx stable and 8hr+ prime small fft and blend.
http://img13.imageshack.us/img13/6287/42644733.png
Yeah I know what you mean.Quote:
Originally Posted by babalouj
My first chip was an i5 2500k L040B671 that I set the bios for 1.385v for this:
http://i246.photobucket.com/albums/g.../Load2500k.jpg
I didn't need a 2600k either but ended up with i7 2600k L041C108 with 1.36v set in bios that does this:
http://i246.photobucket.com/albums/g...9/Capture3.jpg
The only thing stopping me from looking for a 5ghz 24/7 chip on air are the load temps :shrug:
Coolaler hit 5.6ghz on 1.6v with the same batch number L041C108...Quote:
Originally Posted by Sam_oslo
Your C batch sample is looking pretty nice.:up: How high a multi will it boot into Windows with BIOS PLL voltage overide set to disabled?Quote:
Originally Posted by LagunaX
L041B229
5.6ghz boot on Asus Pro Micro with Coolit ECO Water Cooler
http://valid.canardpc.com/show_oc.php?id=1630881
Attachment 111731
Very high vcore:shocked:Quote:
Originally Posted by drnip
Retail 2600K in my country mostly max out around 5.2-5.4
people still find some 5.5-5.7 batch
Microcenter sold me a 2600k - L050A853 - anyone else got one of these yet? Mr. Eldonko?
Quote:
Originally Posted by drnip
That is impressive with a m-atx board!:up:
I noticed that my local Fry's had L050A933 last weekend... I'm not sure if they are still selling SB cpu?Quote:
Originally Posted by SteveRo
I got the worst chip from XS.
L046B509
5000mhz requires 1.485v :D
WATERCOOLED with highend water
5300mhz 8 cores craptage stable, no throttling - 1.675v
LLC enabled.
The chip will not to anything past 100bclk, and for maxing it out, stepping down in bclk pays off... 54x99 is highest freq it will hit.
The chip will not do DDR3-2133, not a chance in hell....
And yet still,.... I am happy with it - I think it is killing as for performance ~7s 1M ~6:30 32M and craptage of 35.5K CPU score...
Best thing in my book is;
I did not have to listen to any of the BS by Will.I.Am in order to use this CPU :)
LOL, some chips can't break 4.5GHz stable in the very same thread, I think you're setting the expectations too high. :p:Quote:
Originally Posted by M.Beier
Expectation 5500mhz 3Dmark craptage 1.65v :DQuote:
Originally Posted by zalbard
Why cant them chips have same quality as women? :mad:
My L039B470 needed 1.52v for that, you were lucky :DQuote:
Originally Posted by M.Beier