**Official DFI LanParty UT X48-T2R(and LT) Discussion

Printable View

Show 100 post(s) from this thread on one page

05-31-2008, 02:55 PM
zsamz_

Quote:

Originally Posted by wilson

Can any1 tell me the difference between using 400;800 and 333;667 because both give a 1.1 ratio ???
Thanks Paul.

400:800 is looser strap;)
05-31-2008, 03:11 PM
wilson

Thanks m8, so 400;800 should help me overclock more that if it was set at 333;667. I only ask as when im messing with occt i can get code 1 and code 4 errors so by using 400;800 i could push my cpu more because of the looser strap on the ram??
05-31-2008, 05:41 PM
zsamz_

Quote:

Originally Posted by wilson

Thanks m8, so 400;800 should help me overclock more that if it was set at 333;667. I only ask as when im messing with occt i can get code 1 and code 4 errors so by using 400;800 i could push my cpu more because of the looser strap on the ram??

use 333/800 strap needs less volts on ram i got mine @ 1230mhz with 2.03v
05-31-2008, 08:40 PM
anubis_is_evil

finally, it detects my E8400 :( weird !

so i tried to pushed it while it detect...

some how its hard for me to clock my E84 into 4.4Ghz 440 X 9...:shakes:

is it true that this X48 have limitation ??? :(

anyone can help me the best voltage setting to raise up about 500 X 9 ?

and btw what is the perfect GTL should be ? is't neccessary to use GTL ?

thx........
05-31-2008, 09:09 PM
asap

every chip may vary m8, i reckon around 1.37 - 1.44 for that clock.. my Q6600 needs only 1.4v stable at 3.6 with this board instead of 1.47v with my old x38 quadGT, but u can find tons of guide here if u havent read.

good luck
05-31-2008, 09:25 PM
anubis_is_evil

Quote:

Originally Posted by asap

every chip may vary m8, i reckon around 1.37 - 1.44 for that clock.. my Q6600 needs only 1.4v stable at 3.6 with this board instead of 1.47v with my old x38 quadGT, but u can find tons of guide here if u havent read.

good luck

wow thx asap for the guide, that is what i'm really2 looking for :D

yur the best ! mate :D

thx again dan terima kasih hehehe
05-31-2008, 10:12 PM
asap

no probs, bro ;)
happy to hear that 45nm of yours working well now :up:

trima kasih
05-31-2008, 10:32 PM
Martinm210

Not sure if this was posted before, but TomsHardware just did an X48 roundup here:
http://www.tomshardware.com/reviews/...d,1941-29.html

And guess what..the DFI came out on top as the best CPU overclocker..:)
http://media.bestofmicro.com/Z/U/106...l/image042.png
06-01-2008, 02:27 AM
safan80

2 Attachment(s)

I can't wait for a bios update I hate the fact that my usb or ps2 keyboards won't respond sometimes at boot.

here's a bench of everest photoworxx DFI x48 vs Asus MF at the same clock. guess which one is faster ;)
06-01-2008, 05:46 AM
MomijiTMO

How have these boards been fairing from a QC point? I will consider buying one tomorrow if people haven't been having too much trouble with the lottery.

EDIT : I see some people have had issues. Time to see what the warranty policy is at my shop haha.
06-01-2008, 06:05 AM
emoners

@Martinm210 & safan80: thanks for posting! :up: but this article from HardwareZone is making the DFI get burned by a clown board. :mad:
06-01-2008, 06:18 AM
MomijiTMO

Bloody hell it is so confusing. HardwareZone got a low OC but I'm going to blame it on their skills. I'm still deciding on whether to get this board or wait for P45. I don't see P45 being that much cheaper, especially when everyone starts piling on the extra things like 4 ethernet ports.
06-01-2008, 06:28 AM
zsamz_

Quote:

Originally Posted by emoners

@Martinm210 & safan80: thanks for posting! :up: but this article from HardwareZone is making the DFI get burned by a clown board. :mad:

yup the dq6 is a clown compared to the dfi
the guy musta been a real n00b
06-01-2008, 07:20 AM
Jor3lBR

Quote:

Originally Posted by emoners

@Martinm210 & safan80: thanks for posting! :up: but this article from HardwareZone is making the DFI get burned by a clown board. :mad:

Toss that article on the trash...

If you don't know what your doing don't buy a DFI and never think about doing a review of it. :down:
06-02-2008, 12:15 PM
TouGe

Cellshocks came today. MemoryC rocks for cheap fast shipping:up:. I've got to go to work in about 30 minutes so I'll mess around with them tomorrow morning and post back my results/problems.
06-03-2008, 04:31 AM
me3850

works goods cell shock with this board...
06-03-2008, 05:20 AM
Praz

LANParty UT X48-T2R, E8400, 496x8, Post 1 Of 3

E8400 04/02 BIOS
496x8, Memory 1190MHz
2x2GB OCZ PC2 9200 Flex2
XFX8800 GTS (G92)
Yellow Slots Used For Memory
VDIMM Measured 2.120V

http://www.edgeofstability.com/image...ios/main_s.jpg http://www.edgeofstability.com/image...ios/volt_s.jpg

http://www.edgeofstability.com/image...s/dram_1_s.jpg http://www.edgeofstability.com/image...s/dram_2_s.jpg

http://www.edgeofstability.com/image.../clock_1_s.jpg http://www.edgeofstability.com/image.../clock_2_s.jpg

http://www.edgeofstability.com/image...os/phase_s.jpg http://www.edgeofstability.com/image.../feature_s.jpg

Code:

CPU Feature Page Thermal Management Control................Enabled PPM (EIST) Mode...........................Enabled Limit CPUID MaxVal........................Disabled CIE Function..............................Auto Execute Disable Bit.......................Enabled Virtualization Technology.................Enabled Core Multi-Processing.....................Enabled Main BIOS Page Exist Setup Shutdown......................Mode 2 Shutdown After AC Loss....................Disabled O. C. Fail Retry Counter..................0 CLOCK VC0 Divider.........................Auto CPU Clock Ratio...........................8x CPU N/2 Ratio.............................Disabled CPU Clock.................................496 MHz Boot Up Clock.............................Auto DRAM Speed................................333/800 PCIE Clock................................100MHz PCIE Slot Config..........................1X 1X CPU Spread Spectrum.......................Disabled PCIE Spread Spectrum......................Disabled SATA Spread Spectrum......................Disabled Voltage Setting Page CPU VID Control...........................Auto 1.2200V CPU VID Special Add.......................108.50% DRAM Voltage Control......................2.150V SB Core/CPU PLL Voltage...................1.510V NB Core Voltage...........................1.504V CPU VTT Voltage...........................1.160V VCore Droop Control.......................Enabled Clockgen Voltage Control..................3.45V GTL+ Buffers Strength.....................Strong Host Slew Rate............................Strong GTL REF Voltage Control...................Disabled CPU GTL 1/2 REF Volt......................110 CPU GTL 0/3 REF Volt......................110 North Bridge GTL REF Volt ................110 DRAM Timing Page Enhance Data Transmitting.................Fast Enhance Addressing........................Fast T2 Dispatch...............................Enabled Clock Setting Fine Delay..................Listed Below CAS Latency Time (tCL)....................5 RAS# to CAS# Delay (tRCD).................5 RAS# Precharge (tRP)......................5 Precharge Delay (tRAS)....................15 All Precharge to Act......................6 REF to ACT Delay (tRFC)...................54 Performance Level.........................Auto Read Delay Phase Adjust...................Listed Below MCH ODT Latency...........................2 Write to PRE Delay (tWR)..................14 Rank Write to Read (tWTR).................11 ACT to ACT Delay (tRRD)...................3 Read to Write Delay (tRDWR)...............8 Ranks Write to Write (tWRWR)..............Auto Ranks Read to Read (tRDRD)................Auto Ranks Write to Read (tWRRD)...............Auto Read CAS# Precharge (tRTP)................4 ALL PRE to Refresh........................6 Read Delay Phase Adjust Page Channel 1 Phase 0 Pull-In.................Auto (7) Channel 1 Phase 1 Pull-In.................Auto (7) Channel 1 Phase 2 Pull-In.................Auto (7) Channel 1 Phase 3 Pull-In.................Auto (7) Channel 1 Phase 4 Pull-In.................Auto (7) Channel 2 Phase 0 Pull-In.................Auto (7) Channel 2 Phase 1 Pull-In.................Auto (8) Channel 2 Phase 2 Pull-In.................Auto (8) Channel 2 Phase 3 Pull-In.................Auto (7) Channel 2 Phase 4 Pull-In.................Auto (7) Clock Setting Fine Delay Page Ch1 Clock Crossing Setting................More Aggressive DIMM 1 Clock fine delay...................140ps DIMM 2 Clock fine delay...................630ps DIMM 1 Control fine delay.................630ps DIMM 2 Control fine delay.................350ps Ch 1 Command fine delay...................840ps Ch2 Clock Crossing Setting................More Aggressive DIMM 3 Clock fine delay...................140ps DIMM 4 Clock fine delay...................420ps DIMM 3 Control fine delay.................420ps DIMM 4 Control fine delay.................420ps Ch 2 Command fine delay...................840ps Ch1Ch2 CommonClock Setting................More Aggressive Ch1 RDCAS GNT-Chip Delay..................Auto Ch1 WRCAS GNT-Chip Delay..................Auto Ch1 Command to CS Delay...................Auto Ch2 RDCAS GNT-Chip Delay..................Auto Ch2 WRCAS GNT-Chip Delay..................Auto Ch2 Command to CS Delay...................Auto
06-03-2008, 05:22 AM
Praz

LANParty UT X48-T2R, E8400, 496x8, Post 2 Of 3

XP SP3

http://www.edgeofstability.com/image...prime_xp_s.jpg

http://www.edgeofstability.com/image..._3d06_xp_s.jpg

http://www.edgeofstability.com/image..._crysis_xp.jpg http://www.edgeofstability.com/image...190_ut3_xp.jpg

3dx Max w/V-ray
Time to render: 14min 32sec

http://www.edgeofstability.com/image...chmark_680.jpg

Everest - Right screen shows C1E enabled

http://www.edgeofstability.com/image...erest_xp_s.jpg
06-03-2008, 05:23 AM
Praz

LANParty UT X48-T2R, E8400, 496x8, Post 3 Of 3

Vista 64 Bit SP1

http://www.edgeofstability.com/image...prime_64_s.jpg

http://www.edgeofstability.com/image...dmark_64_s.jpg

http://www.edgeofstability.com/image...mark_van_s.jpg

http://www.edgeofstability.com/image...0_pcmark_s.jpg

http://www.edgeofstability.com/image..._crysis_64.jpg http://www.edgeofstability.com/image...190_ut3_64.jpg

3dx Max w/V-ray
Time to render: 15min 56sec

http://www.edgeofstability.com/image...chmark_680.jpg

Everest - Right screen shows C1E enabled

http://www.edgeofstability.com/image...erest_64_s.jpg
06-03-2008, 08:54 AM
me3850

anyone have try last beta bios for this board?

LANPARTY LT X48-T2R
2008/05/30
File X48AD530.exe
Major Reasons of Change:
Added New Micro Code for 45nm family CPUs
06-03-2008, 01:37 PM
zanzabar

Quote:

Originally Posted by me3850

anyone have try last beta bios for this board?

LANPARTY LT X48-T2R
2008/05/30
File X48AD530.exe
Major Reasons of Change:
Added New Micro Code for 45nm family CPUs

that sounds like it might help the thermal probe problem on the 45nm
06-03-2008, 02:46 PM
RedHOT

Can't seem to find that file on the DFI site... Nvm found the beta site.

Quote:

Originally Posted by me3850

anyone have try last beta bios for this board?

LANPARTY LT X48-T2R
2008/05/30
File X48AD530.exe
Major Reasons of Change:
Added New Micro Code for 45nm family CPUs
06-03-2008, 06:49 PM
adya

praz: - nice results with 4gb.and vantage. my score was alot lower than that , i wont post it since its fairly misserable lol
just wondering if u tried tighter settings with ram and what happend . also do u think theres any benifit to setting tref higher ? with either latency or stability? i have mine on 16383T but didnt notice a difference . not sure what its function is exactly.
06-04-2008, 08:41 AM
s3rv3r

What is the maximum FSB with dual core support in this motherboard?
It's possible 555MHz in the bus ?
06-04-2008, 09:51 AM
cowie

very nice praz
hey praz in your opinion which board do you like better for max crasy clocks, the p35 ut t2r or the x48 t2r?

Show 100 post(s) from this thread on one page