***Asus Rampage III Extreme Owners Thread***

Quote:

---

Originally Posted by BigBruiseral

Well happy so far but question other owners may help with?

1) I use speedstep on my o/c however wheen speed step kick in my o/c goes from 4.1 to 2.6 great however my vcore stays solid on my UD5 this went down to. All the power savings are on that i can see in the bios.

Thanks

---

So your CPU goes down to 2.6 and the Vcore dorps correct ? Isn't that how Speedstep should work ? Lower the overal speed and Vcore ? and when you load the CPU , Vcore and speed go up ?

If this is the case everything works as it should :)


You really got a nice CPU there Bassplayer

Quote:

---

Originally Posted by DBoone

I have this combo and haven't had a single issue. I'm running a very mild OC at 3.6 on my 930 since this is my first effort at OC and water cooling. I do wish there was better air flow though.

---

I to have this combo, other that a hot nb it's runninng fine.

Does anyone have any experience with this board while running very large amounts of ram? I recently upgraded to this board from a P6X58D Premium. I expected it to have the same ease of use but I find that I am having a much harder time.

I am currently running a 980X with 24gb of Kingston HyperX 1600Mhz. When I was on the P6X58D Premium I was able to run the ram at roughly 1750 Mhz rock stable. I could even push it well beyond that in normal every day use but not Prime95.

After upgrading to the Rampage III Extreme I cannot get the board to post with the ram at 1600Mhz for the life of me. I am currently running it at 1594 Mhz. I normally wouldnt split hairs in saying 1594 isn't 1600 but if I simply up the BCLK 1 more from 159 to 160 the board refuses to post at all.

Anyone seen anything like this with this much ram?

Thanks in advance for any help you can give.

http://www.youtube.com/watch?v=5AOylHaCyUA

take a look at this, it may help !

Quote:

---

Originally Posted by Mrk1525

Does anyone have any experience with this board while running very large amounts of ram? I recently upgraded to this board from a P6X58D Premium. I expected it to have the same ease of use but I find that I am having a much harder time.

I am currently running a 980X with 24gb of Kingston HyperX 1600Mhz. When I was on the P6X58D Premium I was able to run the ram at roughly 1750 Mhz rock stable. I could even push it well beyond that in normal every day use but not Prime95.

After upgrading to the Rampage III Extreme I cannot get the board to post with the ram at 1600Mhz for the life of me. I am currently running it at 1594 Mhz. I normally wouldnt split hairs in saying 1594 isn't 1600 but if I simply up the BCLK 1 more from 159 to 160 the board refuses to post at all.

Anyone seen anything like this with this much ram?

Thanks in advance for any help you can give.

---

lower your blk use the multi
set qpi to 1.36-1.4v
ennable memory ptotect

Quote:

---

Originally Posted by Leeghoofd

So your CPU goes down to 2.6 and the Vcore dorps correct ? Isn't that how Speedstep should work ? Lower the overal speed and Vcore ? and when you load the CPU , Vcore and speed go up ?

If this is the case everything works as it should :)


You really got a nice CPU there Bassplayer

---

Sorry i didt explain very well when the Ghz drops vcore does not. the vcore stays the same at 4.1 and 2.6

thanks

Quote:

---

Originally Posted by donmarkoni

IMO, it's too much. I keep it on Auto (which is usually overkill) and it is set @ 1.244V for UnCore under 4000MHz and @ 1.296V for over 4000MHz.

---

thanks for replying bro..:)..right now i'm curios about the cpuV of my proc since the i7 965 is C0 stepping which iinm requires for more vcore than D0 stepping..i've tried going 4.2g's with HT and turbo disable and set the cpuV till 1.425 in bios..but, the system doesn't boot at all..what is the problem now..??..does the voltage will kill my proc..??..or i have to go higher than 1.425v since my proc is C0 stepping..?

First Test with my new CPU new Board RE3 and new GPU Asus 5870 V2

CPU @ Watercooling

http://img202.imageshack.us/img202/8...ark353k.th.jpg

Uploaded with ImageShack.us

Quote:

---

Originally Posted by kaka_89

thanks for replying bro..:)..right now i'm curios about the cpuV of my proc since the i7 965 is C0 stepping which iinm requires for more vcore than D0 stepping..i've tried going 4.2g's with HT and turbo disable and set the cpuV till 1.425 in bios..but, the system doesn't boot at all..what is the problem now..??..does the voltage will kill my proc..??..or i have to go higher than 1.425v since my proc is C0 stepping..?

---

Don't worry, you need much more voltage to kill your CPU. :D Usually heat kills, so keep it cool.
I had i7 920 before this Xeon and it needed 1.45 for 4.2GHz. I lapped it to keep it in the mid 80's (Celsius).

BTW, post your BIOS settings using template, if you still have trouble.

Finally this is my best scenario for stability and temps.

http://img43.imageshack.us/img43/2693/linx4200.png

Quote:

---

Originally Posted by donmarkoni

Don't worry, you need much more voltage to kill your CPU. :D Usually heat kills, so keep it cool.
I had i7 920 before this Xeon and it needed 1.45 for 4.2GHz. I lapped it to keep it in the mid 80's (Celsius).

BTW, post your BIOS settings using template, if you still have trouble.

---

according to intel's spread sheet, the cpu vid voltage range for this proc was 0.800-1.375v,..that's why i'm a bit afraid of increasing the cpuV,

btw, which one works best, higher BCLK lower multi, or lower BCLK higher multi..??..since my proc is extreme proc, one of my friends said that extreme proc is better to play with lower BCLK and higher multi..is that really true..?

Quote:

---

Originally Posted by kaka_89

according to intel's spread sheet, the cpu vid voltage range for this proc was 0.800-1.375v,..that's why i'm a bit afraid of increasing the cpuV,

btw, which one works best, higher BCLK lower multi, or lower BCLK higher multi..??..since my proc is extreme proc, one of my friends said that extreme proc is better to play with lower BCLK and higher multi..is that really true..?

---

Never mind VID voltage range, use this as a guidance:

http://img519.imageshack.us/img519/8...esabsolute.png

I use up to 1.6V for benching under water. :D

Looks like there is not much difference if you set all relevant clocks (Core/UnCore/QPI/RAM) the same.
There is a discussion going on about your question: For unlocked procs, what provides better performance – high cpu multi or high bclock?

Hey Guys, I have a newb question, which program do you recommend to Overclock 2xHD5850 in Crossfire, and which driver should I use....I know they are a lot of bugs about crossfire and overclocking. Will changing my Bios from beta 0704 to 0802 will help me?

(This is my new Update rig, I add the EK Mobo block and a HD 5850 block, I also used the Triple serial bridge for my VGa Cards and using a Link in the middle of the bridge because I dont have 3 cards)

http://i45.tinypic.com/2po1wt1.jpg

@KaRLiToS

MSI Afterbuner is one off the best, be sure to enable the "enable unofficial overclocking", otherwise you don´t get pass CCC upper OC limit.

Can read about it here, GUIDE to Enabling "Unofficial Overclocking" in MSI Afterburner


Then one more thing, AMD introduced a thing called "ULPS" (Ultra Low Power State) with CCC 10.1 or 10.2 (I do´t remember exacly) which means that it completely shuts down any non-primary GPUs in CrossFire configurations when the video card is working in non-3D mode (e.g. at Windows Desktop).

The thing is that this ULPS can freeze up or BSOD your system, for example if you run Everest, multiple CPUz or other monitor application and also if you "enable unofficial overclocking" and go pass CCC upper OC limit with MSI Afterburner.

ULPS feature is enabled by default installing this driver.

Well there´s a fix, you can edit this setting from windows registry.

You have to search for "EnableUlps" and set them all to 0, when this is done you have to reboot and enable unofficial overclocking for the MSI Afterburner and then you´re good to go and OC those 5850.

The downside is that your system going to draw more power, about 5-10W.

I have done this myself and it works, so get to it :up:


Which driver, hmmm, depends on what your goal are?

I say any of these, 10.3 to 10.6 should do fine.

Quote:

---

Originally Posted by KaRLiToS

Hey Guys, I have a newb question, which program do you recommend to Overclock 2xHD5850 in Crossfire, and which driver should I use....I know they are a lot of bugs about crossfire and overclocking. Will changing my Bios from beta 0704 to 0802 will help me?

(This is my new Update rig, I add the EK Mobo block and a HD 5850 block, I also used the Triple serial bridge for my VGa Cards and using a Link in the middle of the bridge because I dont have 3 cards)

---

This is the program for overclocking your cards http://event.msi.com/vga/afterburner/download.htm and of course the latest official 10.6 drivers from Ati http://game.amd.com/us-en/drivers_ca...indows-7-64bit

here's an odd problem...

why is it EVERY time i go to update bios on this thing, it refuses to use the original installed OS... darn thing makes me reinstall EVERYTHING every time i update the bios regardless if i use BIOS1 or 2...

Ghostleader

You can't even imagine how much you help me...
I already had MSI afterburner and the problem was clearly because of AfterBurner, I was always BSODing.

But now with the ULPS option (in regedit) disabling it solve all my problem so man, thank you very much...

Now I need to stabilise my second GPU because its not as good as my first one (sapphire VS Biostar, but still, its the same PCB)
How Should I overclock them, individually? By turning off PCIE Slot?

Do you think my 950w Power Supply is bottlenecking my overclock? (CPU is at 4.3 Ghz)

Quote:

---

Originally Posted by skuldarin

here's an odd problem...

why is it EVERY time i go to update bios on this thing, it refuses to use the original installed OS... darn thing makes me reinstall EVERYTHING every time i update the bios regardless if i use BIOS1 or 2...

---

Have you checked to make sure the BIOS update didn't change the time set in the BIOS? If it did then it would make your windows key invalid.

Gents...need some help on this question:

This is a bit of a diversion from the bulk of the thread, but as it pertains to a R3E I figured this would be the best place.

I'm considering the addition of a third GTX 480 (currently have 2 GTX 480s in SLI plugged into 16x PCI-E slots 1 and 3 on the board). I also own an Asus Xonar Essence STX, which happens to be a PCI Express x1 sound card (currently plugged into the PCI-E 4x slot on the board).

Due to cable/tubing routing management, I would need to put the sound card into the fourth 16x PCI-E slot to provide enough room for the TRI-SLI configuration. This brings up the question: will placing the sound card in a 16X PCI-E slot cause the board to place the three GTX 480s into a 8x/8x/8x bandwidth configuration? They should run in 16x/8x/8x in standard TRI-SLI mode, but I'm unsure if placing a PCI-E sound card into a 16x slot will affect the performance of the GPUs.

Any help would be greatly appreciated.

is it possible to OC a Xeon 56 ** with R3E?

problem with some options in the bios, OC not possible, perilous or other?

or it can s'OC with the "same" ease a 980X (coeff released without the course)

thanks ;)

Very nice looking build KaRLiToS.

Quote:

---

is it possible to OC a Xeon 56 ** with R3E?

problem with some options in the bios, OC not possible, perilous or other?

or it can s'OC with the "same" ease a 980X (coeff released without the course)

thanks

---

I am using an X5680 and a W3680 on my R3E. OC is possible. Screenie below is from X5680. Not the best vcore around though....

http://i402.photobucket.com/albums/p...zcas8_Edit.jpg

Can somebody who already updated to 0802 bios confirm that ICH PCE value (1.5V) is gone from bios and monitoring software like Everest.

Quote:

---

Originally Posted by OC Nub

Very nice looking build KaRLiToS.

---

Thanks man

Quote:

---

Originally Posted by McDown

Can somebody who already updated to 0802 bios confirm that ICH PCE value (1.5V) is gone from bios and monitoring software like Everest.

---

:yepp:
but not too important