Modded ASUS P5Q/Pro/Deluxe/Premium BIOS

Went from 1402 to 1703m on P5Q-E and now I have something weird.
I'm a underclock/undervolt guy (I know I'm a pariah here :D) and until now EPU served me well through many BIOS updates but now something is not right.
I have a profile for idle with FSB 264 and heavy undervolt. If I choose DDR667 in BIOS then FSB remain at 333 and not 264 as it should be. Good thing is that I can OC a little until ~ 3.5GHz.

Attachment 91045

If i choose DDR800 everything is fine but no OC because memory is drawing me back

Attachment 91046

EIST/C1E/C-State Tech enabled in BIOS. Any ideas?
BTW I'm not an OC-er and it's fine if I stay at stock speeds but I'm curious why this time EPU have this glitch. :)

another something weird
the smart fan with the final 1611m bios didnot work fine
I use it with my zalman cooler with every bios version with no trouble but with this one the fan speed still in the low speed even when I test the cpu with IntelBurnTest but with my any other version the speed increase while cpu loading

Currently running 1702m on my P5Q Deluxe, running fine so far


Intel E8200 @ 3.04
ASUS P5Q Deluxe
G.Skill 800 2x1GB
ATI HD4850

Quote:

---

Originally Posted by burebista

Went from 1402 to 1703m on P5Q-E and now I have something weird.
I'm a underclock/undervolt guy (I know I'm a pariah here :D) and until now EPU served me well through many BIOS updates but now something is not right.
I have a profile for idle with FSB 264 and heavy undervolt. If I choose DDR667 in BIOS then FSB remain at 333 and not 264 as it should be. Good thing is that I can OC a little until ~ 3.5GHz.


If i choose DDR800 everything is fine but no OC because memory is drawing me back


EIST/C1E/C-State Tech enabled in BIOS. Any ideas?
BTW I'm not an OC-er and it's fine if I stay at stock speeds but I'm curious why this time EPU have this glitch. :)

---

I wouldn't know on that one.. largely because EPU is rubbish and I don't use it :p: A good port of call is always to load BIOS defaults and reset CMOS. As well as make sure things like EIST, C1E etc are disabled.

Quote:

---

Originally Posted by hema

another something weird
the smart fan with the final 1611m bios didnot work fine
I use it with my zalman cooler with every bios version with no trouble but with this one the fan speed still in the low speed even when I test the cpu with IntelBurnTest but with my any other version the speed increase while cpu loading

---

Fan settings have been bugged for some time on the P5Q boards. Eg; enable Q-Fan and even if you select "Turbo", the fans will still spin at low RPM.

I done CMOS Clear, but i still dont have boot logo. :/ What should i do to bring it back? P.S. P5Q dlx 1702m P.P.S good bios, ocing on it is better than on official 1702.

I switched from 0803 last night to the 1702m one and everything went smooth for me. I didn't have to clear the cmos or anything. I just reset to default settings and flashed and went back in and adjusted everything back to normal and set it to performance "the dreaded performance seting" and everything continued as normal for me. I played GTA IV for as long as the game would let me had to reboot " normal with game right now until patched" came back into windows and continued playing and no blue screens nothing to indicate an issue. My memory speed test came out as usual. The one thing I wanted to do is to try to push my over clock further but, I was to busy gaming :p:. I will keep posted but, it seems as if the modded 1702 is fine by me.

Quote:

---

Originally Posted by lexus232

I done CMOS Clear, but i still dont have boot logo. :/ What should i do to bring it back? P.S. P5Q dlx 1702m P.P.S good bios, ocing on it is better than on official 1702.

---

Thats a phantom issue, I don't know why some people can see the boot logo and others can't. I attached the boot images I use a few pages back for anyone that wants to try injecting it with asus mylogo.

Quote:

---

Originally Posted by truehighroller

I switched from 0803 last night to the 1702m one and everything went smooth for me. I didn't have to clear the cmos or anything. I just reset to default settings and flashed and went back in and adjusted everything back to normal and set it to performance "the dreaded performance seting" and everything continued as normal for me. I played GTA IV for as long as the game would let me had to reboot " normal with game right now until patched" came back into windows and continued playing and no blue screens nothing to indicate an issue. My memory speed test came out as usual. The one thing I wanted to do is to try to push my over clock further but, I was to busy gaming :p:. I will keep posted but, it seems as if the modded 1702 is fine by me.

---

:up: I'm having great results with 1611m for my Pro, I can hit 3.2GHz @ 1.35v (actual about 1.32v) where before when I had to stick with 703m I needed 1.425v (1.4v real).

Boot images do not appear if you don't export them in correct format. So far i noticed Pain.NET exports them the best when using GIF format with default settings.
Just load the image and save it as 640x480 GIF image. Voila. Worked each and every time. Other methods usually just failed.

My battery just died. In a 5 month mobo it is really strange.

I also had , after battery replacement, some issues with the bios settings being lost after a coold boot.

Reflashed 1406 once againd and its now OK.

Quote:

---

Originally Posted by RejZoR

Boot images do not appear if you don't export them in correct format. So far i noticed Pain.NET exports them the best when using GIF format with default settings.
Just load the image and save it as 640x480 GIF image. Voila. Worked each and every time. Other methods usually just failed.

---

The images are ok, I use paint.net. I really don't know why some can see the boot logo and other don't, I'll have another look at it later probably.

results aren't as scientific as I was hoping for and aren't finished ><

Received my Cell Shock D9GMH kit in this week and have been playing with it and 1613M updated. Attached are screens of results. Lowest I can get the memory is perf 8 3-3-3-9 800 stable, perf 6 3-3-3-9 800 SPI. at 1000Mhz + I cannot drop it below perf 10 4-4-4-12. Not the most experienced with RAM OC'ing but I was under the belief that this kit should perform better.

Stock Results:
http://img261.imageshack.us/img261/6...ultswi3.th.jpg

3-3-3-9 2T 800Mhz (1-1, E8400 @ 3.6)
http://img356.imageshack.us/img356/9...8800ti0.th.jpg

5-5-5-15 2T Perfomance level 10 1000Mhz (1-1 E8400 @ 4.775)
http://img53.imageshack.us/img53/388...rf10qo0.th.jpg

I also have a question, according to the Motherboard temp sensor, the board reports it running at 29C @1.3V for the 'motherboard sensor' Normally this would be the chipset temp no? anyone know of the safe voltage levels for this chipset? I think that is what is holding the OC back at this point but I am not sure

Something wrong with both standard 1703 and 1703m!? As soon as I do any OC´ing, the bios resets the settings so after post im back with all default settings?? Anyone know how to fix this?? As this isnt right!?

Quote:

---

Originally Posted by Triage

results aren't as scientific as I was hoping for and aren't finished ><

Received my Cell Shock D9GMH kit in this week and have been playing with it and 1613M updated. Attached are screens of results. Lowest I can get the memory is perf 8 3-3-3-9 800 stable, perf 6 3-3-3-9 800 SPI. at 1000Mhz + I cannot drop it below perf 10 4-4-4-12. Not the most experienced with RAM OC'ing but I was under the belief that this kit should perform better.

Stock Results:
http://img261.imageshack.us/img261/6...ultswi3.th.jpg

3-3-3-9 2T 800Mhz (1-1, E8400 @ 3.6)
http://img356.imageshack.us/img356/9...8800ti0.th.jpg

5-5-5-15 2T Perfomance level 10 1000Mhz (1-1 E8400 @ 4.775)
http://img53.imageshack.us/img53/388...rf10qo0.th.jpg

I also have a question, according to the Motherboard temp sensor, the board reports it running at 29C @1.3V for the 'motherboard sensor' Normally this would be the chipset temp no? anyone know of the safe voltage levels for this chipset? I think that is what is holding the OC back at this point but I am not sure

---

Try setting NB and SB voltage to 1.3v and working from there. I can run PL6 @ 1200MHz with my GKX kit so something in your config deffinately isn't quite right.

Quote:

---

Originally Posted by MonsterMan

Something wrong with both standard 1703 and 1703m!? As soon as I do any OC´ing, the bios resets the settings so after post im back with all default settings?? Anyone know how to fix this?? As this isnt right!?

---

Tried loading setup defaults and clearing CMOS? (proper clear that is, remove power cord and battery)

Ket, can u please add downgrade ability from EZ Flash in 17xx bioses?

I don't need to add "support", its already there. :\ Amazes me how many people don't look at the options tab in the scroll-down window of asus update. :p:

Quote:

---

Originally Posted by Ket

I don't need to add "support", its already there. :\ Amazes me how many people don't look at the options tab in the scroll-down window of asus update. :p:

---

huh, try to downgrade with enabled BIOS Downgradable in options and you will see this: Warning! The BIOS image can't use in this motherboard. (The EEPROM Type incompatible) :p:

Ok so I could use a little advice.

I am re-building my system to include a P5q Pro, E8600, and 4x1GB G. Skill HZ 800 RAM.

My goal is 450-470 FSB with the memory synced. I have read most of this thread and cannot come to a good conclusion as to what is the best bios for my config.

I've found this page on a BIOS of MSI P35-Neo2...
could be possible to implement the same thing [choosing IRQ for specific PCI slot] on Asus [p5q] ?
thank you

Quote:

---

Originally Posted by lexus232

huh, try to downgrade with enabled BIOS Downgradable in options and you will see this: Warning! The BIOS image can't use in this motherboard. (The EEPROM Type incompatible) :p:

---

Sounds like your trying to use the wrong BIOS file :p:

Quote:

---

Originally Posted by Froggy

Ok so I could use a little advice.

I am re-building my system to include a P5q Pro, E8600, and 4x1GB G. Skill HZ 800 RAM.

My goal is 450-470 FSB with the memory synced. I have read most of this thread and cannot come to a good conclusion as to what is the best bios for my config.

---

Very subjective. I would start with 1613m though.

Quote:

---

Originally Posted by lupo17

I've found this page on a BIOS of MSI P35-Neo2...
could be possible to implement the same thing [choosing IRQ for specific PCI slot] on Asus [p5q] ?
thank you

---

Probably, but not without some work using tools I don't have.

Quote:

---

Originally Posted by Ket

Sounds like your trying to use the wrong BIOS file :p:

---

i tried many bioses for my mobo, and always i see this. And not only i expecting this problem with 17xx bioses, in P5Q Deluxe thread i saw other people with such problem. :yepp: That's why i asking for your help.

Have you tried resetting your CMOS (remove battery and power cord) and uninstalling asus update and downloading the latest one?

Quote:

---

Originally Posted by Ket

Have you tried resetting your CMOS (remove battery and power cord) and uninstalling asus update and downloading the latest one?

---

i tried resetting CMOS many times (with cord removing, but without removing battery) and tried latest Asus Update, it didn't helped. Also tried to install 6th version of asus updt, but it says that no Asus mobo detected. :confused:

Ok, I'd try the following and if it doesn't work.. even I'll have to have a good hard think :p:

1. Uninstall asus update
2. Uninstall video and audio drivers
3. Power down, remove battery, power cord, set CMOS jumper to "clear" position
4. Press power button 3-4 times for 3 seconds each to discharge the capacitors
5. Leave for 5-10 mins then power back up
6. Load BIOS defaults, save and exit.
7. Re-install Intel chipset drivers v9.0.0.1009 (AFAIK theres no easy way to uninstall the drivers, hence why uninstalling them isn't listed above)
8. Restart
9. Install asus update (restart if you feel it may help)
10. Try flashing your BIOS.

Intel P45 Chipset Drivers v9.0.0.1009

I have been running the m1406 bios for my p5q-e and just updated to the m1703 bios. I used asus update and the bios was applied successfully. I rebooted and then entered setup. The bios confirmed it was bios 1703. I tried to load from a saved OC profile but the settings were not applied correctly so I had to manually update all bios settings. I set everything to the way it was when running the m1406 bios but noticed that several options were missing like ez flash. I saved my settings and rebooted and now I get nothing.

Computer turns on and fans run but I just get a blank screen. I powered off the computer and removed the power cable. Set the jumper to clear cmos position for about 10 seconds and then put back to normal and tried to boot. Still I get nothing.

Is there any way to roll back to the old bios? Seems like my mb is hosed now.

Quote:

---

Originally Posted by darklink

I have been running the m1406 bios for my p5q-e and just updated to the m1703 bios. I used asus update and the bios was applied successfully. I rebooted and then entered setup. The bios confirmed it was bios 1703. I tried to load from a saved OC profile but the settings were not applied correctly so I had to manually update all bios settings. I set everything to the way it was when running the m1406 bios but noticed that several options were missing like ez flash. I saved my settings and rebooted and now I get nothing.

Computer turns on and fans run but I just get a blank screen. I powered off the computer and removed the power cable. Set the jumper to clear cmos position for about 10 seconds and then put back to normal and tried to boot. Still I get nothing.

Is there any way to roll back to the old bios? Seems like my mb is hosed now.

---

Well there must be someway to get it work, maybe try another rams or even change memory slots (yellow -> black /// black - yellow)

P5Q-E Got 2x bios chip, you will see em they are in right downcorner, Just swap em and it will work.

(And its possible to buy new bios chips)