A Positive Look at the Antec Nine Hundred (900) Case

Printable View

Show 100 post(s) from this thread on one page

06-28-2008, 05:37 PM
Solzar

Quote:

Originally Posted by kingvan

hey,
can someone show me step by step on how i can open the top part of the antec 900 case.

basically there's 6 plastic tabs(only 4 visible) and 2 screws.(one of which is holding a ground wire from the front panel). take off the 2 screws, and then undo the 4 tabs that you can see. the last part kinda scares me every time i do it, but u gotta basically wiggle it around and pull up, but not too tough because there are wires hanging down.

http://www.tomshardware.com/forum/24...mm-replacement

This is toms hardware version and there is a diagram, and better description.
the screws are highlighted in yellow, and its had to see but there are faint yellow circles around the locations of the plastic tabs

(probably should have read the post right after b4 i posted but o well maybe someone else will need it.)
06-30-2008, 07:15 AM
Arthur Dent

Anybody Interested ?

I need to buy a spare side panel for my 900 (the solid one not the windowed one). Any ideas?

As i cant seem to find one anywhere i was considering buying a new case and reselling the chassis, windowed panel, 200mm fan, drive caddies, 120mm fans, etc to others who are also unable to find spare parts, or want to try modding without having to pull their own 900 to pieces first.

Prices would be low - just enough to recover most of my outlay and postage!

Anyone interested ??
06-30-2008, 01:36 PM
dalosiman

Quote:

Originally Posted by Arthur Dent

I need to buy a spare side panel for my 900 (the solid one not the windowed one). Any ideas?

As i cant seem to find one anywhere i was considering buying a new case and reselling the chassis, windowed panel, 200mm fan, drive caddies, 120mm fans, etc to others who are also unable to find spare parts, or want to try modding without having to pull their own 900 to pieces first.

Prices would be low - just enough to recover most of my outlay and postage!

Anyone interested ??

Absolutely, I would be interested in one of the front drive caddies with fan and a couple of the 120 mm fans if you decide to do this.
06-30-2008, 01:47 PM
JINU

Quote:

Originally Posted by Arthur Dent

I need to buy a spare side panel for my 900 (the solid one not the windowed one). Any ideas?

As i cant seem to find one anywhere i was considering buying a new case and reselling the chassis, windowed panel, 200mm fan, drive caddies, 120mm fans, etc to others who are also unable to find spare parts, or want to try modding without having to pull their own 900 to pieces first.

Prices would be low - just enough to recover most of my outlay and postage!

Anyone interested ??

wait your trying to buy the solid side panel right? .....
http://www.antec.com/Detail.bok?no=547
06-30-2008, 03:28 PM
=>WiLL<=

I have a spare right solid panel. I ordered it thinking it was the windowed panel, because it said "left side panel". When looking at the case from the front, the "left" panel is the "windowed" panel.

It wasn't.

So I ended up making my own full window mod. I am saving that extra blank panel for a custom laser-etched design.

You can find one on Antec's site, like previously mentioned. I think it came to $23 after shipping.
07-01-2008, 02:39 AM
Krambo~SPARTA~

Hi all.

Saw the forums a week or so ago and thought id join and show sum pics of the case, no where near as good as u guys but thought id share anyway.

constructive criticism be great :)

http://i133.photobucket.com/albums/q...j/DSC00473.jpg

http://i133.photobucket.com/albums/q...j/DSC00466.jpg

http://i133.photobucket.com/albums/q...j/DSC00472.jpg

http://i133.photobucket.com/albums/q...j/DSC00421.jpg

http://i133.photobucket.com/albums/q...4122007329.jpg

http://i133.photobucket.com/albums/q...0620081123.jpg
07-01-2008, 08:31 AM
zowle

Anyone knows a trick for put PSU fan down without a dremel job? :P
07-01-2008, 12:28 PM
Power5

Buy a PSU that only breathes in from the front.
07-01-2008, 12:34 PM
apexracing

Cut a hole in the bottom of the case and put a filter over it.
07-01-2008, 02:06 PM
Vivi

apexracing has a good idea. this case is awesome for modding, just dont be afraid and cut away :)
07-01-2008, 02:41 PM
zowle

I said that i can't cut anything but thanks for answers ;)
07-01-2008, 02:55 PM
Vivi

sorry i did not see that you typed that :(
07-01-2008, 03:00 PM
zowle

Quote:

Originally Posted by Vivi2

sorry i did not see that you typed that :(

Don't worry man
07-01-2008, 05:22 PM
=>WiLL<=

Quote:

Originally Posted by zowle

Anyone knows a trick for put PSU fan down without a dremel job? :P

A dremel is better for square cuts. Your best bet to make a perfect hole for the PSU is a 4-1/2" hole saw, attached to a drill. :D

Drill it slow. It will turn out beautiful.
07-01-2008, 06:31 PM
DaIceMan

Hey zowle, not sure what FSB and multiplier you are running, but I've had good luck with my E6600 at 3.2Ghz, running 400 x 8 multiplier. I think the only voltages changes I made was bumping the NB up a step or two. Runs rock solid stable, and even Folding@Home 100% core, it runs around 45-46 deg C in my 900 with a Tuniq Tower 120 cooler.

Just a little info, in case you wanna do a little more tweaking.
07-02-2008, 12:13 AM
4868

Hey, i was wondering how you guys got the acrylic feet with the blue LEDs to fit under the PSU on this case. I'm having trouble with this. Any help or tips for this?

Thanks.
07-02-2008, 12:44 PM
=>WiLL<=

Quote:

Originally Posted by 4868

Hey, i was wondering how you guys got the acrylic feet with the blue LEDs to fit under the PSU on this case. I'm having trouble with this. Any help or tips for this?

Thanks.

I mounted mine on the sides of the PSU, out of the way. I then matched that same distance on the front two feet.
07-02-2008, 01:38 PM
MetalRush

Oh - My - God :shocked:
See what you did WiLL :eek:
It is spreading ! People actually LIKING those UGLY feet... :shakes:

So how about it, my friend... when are you going to show us your new shoes? :ROTF:
07-02-2008, 05:41 PM
DaIceMan

Quote:

Originally Posted by MetalRush

Oh - My - God :shocked:
See what you did WiLL :eek:
It is spreading ! People actually LIKING those UGLY feet... :shakes:

So how about it, my friend... when are you going to show us your new shoes? :ROTF:

I knew this reply was coming. LOL!
07-02-2008, 10:49 PM
sailrabbit

Quote:

Originally Posted by 4868

Hey, i was wondering how you guys got the acrylic feet with the blue LEDs to fit under the PSU on this case. I'm having trouble with this. Any help or tips for this?

Thanks.

I hot glued the wires flat to the floor and the PS fit. Mounted the switch on the bottom too:

http://img169.imageshack.us/img169/4...feetxd1.th.jpg

The feet reallty are ugly if they are not lit.. but look really good if they are IMHO :cool:
07-02-2008, 10:54 PM
=>WiLL<=

Ha ha

Nice to see the two blue LED feetness reply so quick.

I'm cooler than you now tho since I use "above average" black rubber feet.
07-03-2008, 07:36 AM
MetalRush

Why did you glue them Sailing Bunny?
You had to drill holes for the LEDs anyway, so why not drill small holes for the screws? Because I think that glued 'plastic' is not very adhesive to metal.

Oh btw.... those feet are ugly in ANY way... lit or not :D

@ WiLL:
Poser! I want pictures.. as proof!

;)
07-03-2008, 09:23 PM
jdrom
Here's my Antec 900:

http://i85.photobucket.com/albums/k7...s/DSC03188.jpg

http://i85.photobucket.com/albums/k7...s/DSC03206.jpg

Done a bunch of modifications to it since this thread gave me tons of ideas...
- Basic hole cutting for cable management
- Painted it semi-gloss black
- Cut some new water cooling holes
- I did cut the hole in the bottom for my PSU since I used to have a OCZ GameXStream but now its useless
- Installed mesh filters into 6 drive bays (the ones with fans)
- Cut a hole in the top tray for a fillport and another for the ASUS LCD Poster wire
It's kept me busy for sure especially since it was my first time really modifying a case. It'll be hard to part with it when I finally decide to move up to a full tower.
07-03-2008, 09:29 PM
Bubbaxm2

That looks damn good jdrom!
07-04-2008, 06:34 AM
sailrabbit

Quote:

Originally Posted by MetalRush

Why did you glue them mighty Sailrabbit?
You had to drill holes for the LEDs anyway, so why not drill small holes for the screws? Because I think that glued 'plastic' is not very adhesive to metal.

Oh btw.... those feet are ugly in ANY way... lit or not :D

lol.. I didn't hot glue the feet.. the wire to the floor as stated. Kept it from moving as I installed the PS. Tight fit.

Here is a sexxxy pic of the fugly feet for your viewing pleasure PlasticRush!

http://img225.imageshack.us/img225/9155/14finji0.th.jpg

Oh I picked up 4G of Cruical Tracer with the blue LEDs and a Thermaltake A2417 Flare Pad Blue LED Mouse Pad to go with the theme. :rolleyes:

http://us.st12.yimg.com/us.st.yimg.c..._2007_12623468

Show 100 post(s) from this thread on one page

All times are GMT -8. The time now is 10:12 PM.

XtremeSystems