Printable View
P5Q Deluxe rocks. I have virtually no vdroop at all. 1.3000 set in BIOS, 1.296 reported by CPUZ under load.
Currently running my X3350 @ 470 x 8 w/ 1.3000 v in the BIOS. 3 cores are stable with lower voltage but the 4th core always crashes p95 so I'm still finding stable settings for 3.8ghz.
Leeghoofd
Thanks:up:
it helps:) i still have AI Clock twister on auto and going to do some stability tests now
Thats what I wanted to see. :clap:Quote:
Originally Posted by Dalten
Guys , what can the Maximus 2 do that the P5Q deluxe cant ?
:up:
That's ok until you try to understand why your 24 hour Prime95 stable rig is unstable at idle.Quote:
Originally Posted by .Tret
New mobo for me with Q6600
400 fsbx8 multi
Why core temp appears ok and CPU-Z wrong
You still got EIST on mate in the bios... it drops down to 6x multi when CPU is idle... do you need 1.39Vcore for 3.2Ghz ? LLC enabled yes or no ?
Leeghoofd - hi mate , what do you reckon ?Quote:
Originally Posted by aussie-revhead
:up:
Dunno mate, I don't have the MF II, but next week my mate will have his 2 4870 cards and he will test them on his P5Q dlx, hopefully he can deliver us some good news that the Tweaktown review was a bit over the top... I like my board with a single card solution... totally amasing to me... P5K Dlx revisited for me...easy setup and reliability... and coming from an Nvidia mobo you will be pleasantly surprised
Now LLC is enable and disable some Intel throating technologiesQuote:
Originally Posted by Leeghoofd
Solved
Thanks man :)
I will post later my bios settings
How I will go higher with muskin 800MHz 5-5-5-12 memory
Triyng with all straps I can go higher than 400 fsb and KEEP MEMORY AT 800 MHz
How do you know if your computer is stable at load but unstable at idle?Quote:
Originally Posted by Cob
I never shut my computer off and it has been sitting on idle for about two weeks. What do you use to test idle stability?
You can't test for stability at idle, other than letting the machine sit idle.
How I will go higher with muskin 800MHz 5-5-5-12 memory
Trying with all straps I can go higher, with 8 multi, than 400 fsb and KEEP MEMORY AT 800 MHz 1:1
any suggestion?
best Bios so far is ???
No real differences from 0702 onwards.
That sounds good to me , I think I will order one .Quote:
Originally Posted by Leeghoofd
:up:
Just installed 1 4870, getting around 17k 3d06 with cpu at 4250mhz. Got another 4870 sat here but dont wanna try to run 2 with PSU in sig so will have to wait till a new one comes next week.Quote:
Originally Posted by Leeghoofd
Just finishing measuring the voltages of the 0901.Quote:
Originally Posted by R@ptor =]]
All stays the same as my previous overvoltage readings with the 0702:
http://img204.imageshack.us/img204/1...eadingscl8.jpg
But I downgrade back to 0803 because I feel it more solid than 0901.
:up:
jVIDIA
Thank you for information,
is it mean putting a min.voltage value on this mobo leading to serious overvoltage? also for SB and PCIE?
What are the pullins for?
Thanks mate! ;)Quote:
Originally Posted by jVIDIA
So i will flash the bios to 0803. you don't test thios bios (0803) about these readings yet?
I don't have a DMM.
And, I do not know how to use it :shrug:
If I had one, and use knew, I could help you with these readings :rolleyes:
Hey guys and hope you can help.
New install E8400 and P5Q Pro using 2 X 2GB Corsair DDR2800 PC6400 5,5,5,18 1.9v
Everything runs fine at default, all stress testing is ok.
I made only a few changes. Just taking FSB Freq to 400 (which my RAM is rated for) and rasing DDR Volt to 2.0.
I can not get through memtest w/o errors. I lowered CPU ratio so CPU is not at 3.2ghz. I tried raising DDR volt 2.1, and no help. I also tried using DDR slots 2/4 instead of 1/3.
This RAM ran fine @DDR800 in previous P5B 965 board. What should I try next? I really don't think the RAM is bad.
AI Overclock tuner: manual
CPU Ratio Setting: 8
FSB Strap to North Bridge: AUTO
FSB Frequency: 400
PCI-E Frequency: 100
DRAM Frequency: 801
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: MANUAL
5-5-5-18-5-50-6-3
8-3-5-4-6-4-6
14-5-1-6-6
DRAM Static Read Control: DISABLED
DRAM Read Training: AUTO
MEM. OC Charger: AUTO
AI Clock Twister: AUTO
AI Transaction Booster: MANUAL
PL 13
CPU Voltage: AUTO
CPU GTL Voltage Reference : AUTO
CPU PLL Voltage: AUTO
FSB Termination Voltage: AUTO
DRAM Voltage: 2.00
NB Voltage: AUTO
NB GTL Reference: AUTO
SBridge Voltage: AUTO
PCIE SATA Voltage: AUTO
Edit: I changed all the voltages from AUTO to the "defaults" I found in this thread (or close). I lowered CPU ratio to X 7 so Im now running 2.8ghz. I'm not sure if changes the voltages fixed it or dropping the CPU down below stock speed. Either way I just completed 1 pass of memtest w/o error. I will let it run for a bit and see what happens. If I increase the CPU speed, is the CPU voltage the only thing I should raise? I'm on water cooling and it seems that 55c is max load temp currently.
CPU Voltage: 1.2675
CPU GTL Voltage Reference : AUTO
CPU PLL Voltage: 1.5
FSB Termination Voltage: 1.20
DRAM Voltage: 1.90
NB Voltage: 1.10
NB GTL Reference: AUTO
SBridge Voltage: 1.10
PCIE SATA Voltage: 1.5
SB and PCI-E I don't know yet because I don't know where are the reading points for those two values.Quote:
Originally Posted by Paodaf
Anyone knows that ?
The 0803 is 99% the same.Quote:
Originally Posted by R@ptor =]]
What are the pullins foir?
I believe they are almost the equivalent of running one notch lower tRD (Performance Level).Quote:
Originally Posted by truehighroller
I know they affect Everest scores about the same was as dropping to one lower tRD notch anyway.
So in my case, i run tRD 8 + all pull-ins enabled, since i cannot POST if i run tRD 7.
Well, i've spent hours & hours changing timings & rebooting, running HCI & rebooting...etc.
Doesn't really help that i've updated bios pretty much every time a new one is out.
There are three sets of subtimings on this mobo, & unfortunately for my tweaking, one (or a few) of those timings affects HCI Memtest stability in a big way.
So i'm presently running the 1st set manually set to the same timings as auto puts them at, & the second & third set i've set one notch looser for each one, since auto sets one (or more) of them a wee bit too tight...just haven't figured out which one(s) wrecks stability...there's only like 12 to pick from :(
One thing i am happy with is how much lower i've been able to drop NB voltage & vDIMM.
I've gotten to somewhere i'm pretty happy with in terms of performance, but also stability, though i'm still going to eventually try to figure out which of those remaining 12 subtimings prefers being set looser.
HCI Memtest stable bios settings for bios 0901:
AI Overclock tuner: Manual
CPU Ratio Setting: 8
FSB Strap to North Bridge: 333
FSB Frequency: 442
PCI-E Frequency: 101
DRAM Frequency: 1061
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Manual
1st Information:
CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : 3
Row Refresh Cycle Time: 55
Write Recovery Time: 6
Read to Precharge Time: 3
2nd Information :
READ to WRITE Delay (S/D): 9
Write to Read Delay (S): 4
WRITE to READ Delay (D): 6
READ to READ Delay (S): 5
READ to READ Delay (D): 7
WRITE to WRITE Delay (S): 5
WRITE to WRITE Delay (D): 7
3rd Information :
WRITE to PRE Delay: 15
READ to PRE Delay: 6
PRE to PRE Delay: 2
ALL PRE to ACT Delay: 7
ALL PRE to REF Delay: 7
DRAM Static Read Control: Disabled
DRAM Read Training: Disabled
MEM. OC Charger: Enabled
AI Clock Twister: Moderate
AI Transaction Booster: Manual
Common Performance Level: 08
All Pull-Ins: Enabled
CPU Voltage: 1.4
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1.52
FSB Termination Voltage: 1.22
DRAM Voltage: 1.96
NB Voltage: 1.24
NB GTL Reference: AUTO
SBridge Voltage: 1.1
PCIE SATA Voltage: 1.5
Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : AUTO
NB Clock Skew : AUTO
http://n7.slayernine.com/files/OCing...5%20STABLE.jpg
http://n7.slayernine.com/files/OCing...kew%20auto.jpg
Gotten my Everest score up a bit too, & on stable settings.
I can get it quite a bit higher, but it'll fail HCI then...
Thanx everyone for the help again; i'll continue to tweak :)