Printable View
Here a Foto of my GPU before. Perhaps anybody can see some Infos about the Codes on it? In the moment i only connect the 2 golden point without put some silver Paint in the Lasercut Hole. Perhaps blueremy have put some paint in the hole?
[url]
?http://www.opsosite.de/upload/data/media/21/R420.jpg
You don't need paint in the laser hole but if it gets in it's no problem.
According to his methods your core should be able to be modified.
http://www.pcunleash.com/bbs/zboard....emReview&no=26
The following link has been translated from a friend of mine.
.
I'm sorry, i did't know that link posted already.
No problem...thanks for trying to help!:thumbsup:Quote:
Originally posted by blueremy
I'm sorry, i did't know that link posted already.
here the nearest photo i can make from the points. so you can see some circuits under the green stuff. perhaps it help somebody.
http://www.opsosite.de/upload/data/m...Up_Pipes_2.jpg
Today i modded again and only 12 Pipes again. so the conclusion of this story is: Not all X800Pro can reactivate all 16 Pipes and the code on the GPU is not interessded.
The Mod i have done, was working right, because before i have between points 1-2 2-3 and 1-3 connection. After i have too connection between 3-4 and 1-4 and after modding, connection too between point 1 and 4 and the nearest smd resistor. and that was not before. so the modd is correct but only 12 pipes again.
:(
So it is only a luck.
I located a BBA X800 Pro with the AA .1 on the core.
Ill post how it goes
Good luck. Don't think any BBAs have been successful yet. If yours is that could tell us something!:toast:Quote:
Originally posted by FUGGER
I located a BBA X800 Pro with the AA .1 on the core.
Ill post how it goes
On my GPU (pic higher) you can see that i have too an AA and .1 and it works not with 16 pipes. thats only luck. but its interessting that the reaction is not the same like the 9800se's with ckeckers and artifacts.Quote:
Originally posted by FUGGER
I located a BBA X800 Pro with the AA .1 on the core.
Ill post how it goes
How about 1-5, 2-5, 4-5, or 5-3?
Nothing, no connection
Didnt work, I have good connection to the contact pads and did the flash update.
hmmm, but i have between 3-4 so someone works. ?
Yep...I'm thinking that this is not any better than the softmod. Did you try that one? Some guys at Rage3D claim to have done it successfully, but info is pretty sketchy.Quote:
Originally posted by FUGGER
Didnt work, I have good connection to the contact pads and did the flash update.
I have a big please to all there the Mod runs right with 16x1:
Can you say me, if you can messurement with Multimeter some contact between the 4 little golden points and the bigger point (5 or named M) in the mittle after Mod?
I only have contact between the 4 little points and not to the
5. point in the mittle.
And where can i download an Sapphire X800Pro Bios? Only ATI i found.
Thanks
Tried it on a Club3D today and it didn't work so put another non-sapphire card on the list of failures. This card has a AA .1 core so forget about the stepping, there's now way to tell before you actually do the mod.
my x800pro sapphire, has this code: GA8999.1
I've triyed the mod with conductive paint, but i can't have 16 pipelines. Why? isn't ok the code???? i've also flashed the x800pro with x800xt bios and now my graphic card is named "R420" with the xt frequencies...I've tryed farcry with stock cooling, but i have big artifact!:(
here a screen:http://www.euromodding.com/modules/c...0/Immagine.JPG
is it a sapphire?Quote:
Originally posted by zombie
here the nearest photo i can make from the points. so you can see some circuits under the green stuff. perhaps it help somebody.
http://www.opsosite.de/upload/data/m...Up_Pipes_2.jpg
Its an Powercolor, but the Core and the green opg package arround is for all Cards the same from the same Chip Factory. Only the PCB is then build from other manufactures like powercolor, Sapphire etc.
@phantom: Do you use Cat. 4. 6b ? Then i have too R420 in the System Tray and the artefacts can be from to high clockrates. set the rates with ATI Tool down. Do you have then artefacts ?
Forgot the Codes on the Core, that infos are not helpfull.
is your powercolor x800 pro now mooded into x800 xt and running @ 16 pipes?Quote:
Originally posted by zombie
Its an Powercolor, but the Core and the green opg package arround is for all Cards the same from the same Chip Factory. Only the PCB is then build from other manufactures like powercolor, Sapphire etc.
@phantom: Do you use Cat. 4. 6b ? Then i have too R420 in the System Tray and the artefacts can be from to high clockrates. set the rates with ATI Tool down. Do you have then artefacts ?
Forgot the Codes on the Core, that infos are not helpfull.
modded yes but no 16 pipes
Phantom, what is your full code ?
damn, so only sapphire successes... i should buy a sapphire