If I am not mistaken when u run 1 GFX u just get 16x lanes , but when u run Xfire then u will get 2x 8x lanes on a P45, whereas the X38/X48 got 2x 16x
Printable View
If I am not mistaken when u run 1 GFX u just get 16x lanes , but when u run Xfire then u will get 2x 8x lanes on a P45, whereas the X38/X48 got 2x 16x
I reviewed both the P5Q Deluxe and MSI P45 boards a couple of week back which you may find interesting if you need some more info:
P45 Showdown
Can you test the max fsb on p5q with a wolfdale?Quote:
Originally Posted by Ic3man
Sure but if you put the radi controller in 2nd or 3rd ? pcie slot... it would get zero lanes with your explanation. So i think mobo will handle it like a 2nd gfx card and switch to 8/8 config. Pls correct me if i'm wrong :)Quote:
Originally Posted by CERO
Niceee Leeghoofd!!
waiting for more tests of over!
You get 8/8/4, that 4 running through the southbridge :)Quote:
Originally Posted by ic3m4n2005
Is this good enough? :)
@ BigJoe
can you tell me you mem settings?
i have some trouble with my P5Q Dlx (Bios 0506) and the 1:1 divider!
it boot only with 5:6 divider :(
Or can you send me Bios 0302?
I'd love to see how this board performs with 45nm quads.
@Juplier
http://spacemaster.sx-team.com/Testo...ax%20Q9450.JPG
@Chri$ch
Send me PM with your mail :wave:
Nice results Big joe!
how i use CPU GTL voltage reference?
0.630x is default for all REF voltage @ ASUS MoBo ;)
and max FSB with dual 45nm? :D:D
What's is the function of pci express sata voltage?
@ BigJoe
thx for Bios 0302, but it wont help :(
my P5Q Dlx wont run with divider 1:1
Can you send me you Bios mem settings?
Thanks
Chris
Strap 333, first four bla bla something settings @ Normal, CL5-5-5-15, all other settings @ AUTO for now :wave:
BigJoe I'm currently testing ram bandwith, but geting very poor results here ( not even matching my P5K dlx )... Lowest power level I can select is 9 otherwise no post at 400FSB, for 450FSB limited to 10, Ram at moderate, Ram in Sync at 5-5-5-15 2T (2 x 2 Gb dimms)
http://users.pandora.be/OAP/P5QDlx/PQ53200.JPG
http://users.pandora.be/OAP/P5QDlx/PQ53600.JPG
Left P5K Dlx and right P5Q Dlx
RAM speed and divider in the P5Q? Also, the P5K is at the same perf level?
P5K is one performance level lower... prolly a newer bios will fix this as I cannot get the board to boot ( no matter what voltages I put in...)Quote:
Originally Posted by STaRGaZeR
Also Static read control needs to be disabled otherwise no post either here...
I do not have time to test and reboot now, but i will test and photo my settings tommorow ;)
I got one SS for you now ;)
http://benchmark.co.yu/forum/attachm...chmentid=37695
Quick test with QX9650... never got this CPU to work at 485Mhz before ( didn't post with the Maximus SE) will see if I can get it higher...
http://users.pandora.be/OAP/P5QDlx/P5Q9650.JPG
Will make a template tonite so we can compare settings more easily....
For those that are questioning the S-ATA ports, here are two pictures with my 8800GTX in the case :
http://users.pandora.be/OAP/P5QDlx/P5QDlx%20015.jpg
http://users.pandora.be/OAP/P5QDlx/P5QDlx%20016.jpg
Don't look at the mess inside, watercooling needs to be cleaned so reverted back to air at the moment...
Thx for the quick test.
How about VCore? Big fluctuations when under load?
Where did you get yours?
I won't test Loadline calibration Jupiler, bit scared of bad spikes with the Qx... (cost me too much) might test it with one of the E8XX's...
But here's a quick run at 3.6Ghz and loadline on auto too but that is the same as disabled...
http://users.pandora.be/OAP/P5QDlx/P5Q9650VCore.JPG
Shop http://www.jaha.be
Don't look at the hour, didn't even set date time correctly just booted , hooked up the P5K Dlx Hd and off it went...
Thank you.