Tell me about it!Quote:
Originally Posted by IanY
Just watched a demo of the new release of my fave 3D application running on 12 cores.
Life in ignorance was OK, but now I know!
Printable View
Tell me about it!Quote:
Originally Posted by IanY
Just watched a demo of the new release of my fave 3D application running on 12 cores.
Life in ignorance was OK, but now I know!
BumpQuote:
Originally Posted by ranker
Bump for an answer too. If i can add this instead, :up: im tossing out my meanwell for another day.Quote:
Originally Posted by Turtle 1
how well did pa120.3 line up in the front to mount?
Bump. Petra, oh wise one, can you give us an answer? =DQuote:
Originally Posted by NaeKuh
The MM case`s match the thermochill rads m8 so dont worry.
Sorry wasn,t watching thread thread. Yes you can undervolt the RD30 which is the case with almost all DC motors.- The only thing you need to worry about is the Amp. draw . I She hasn't had a problem. By the way . Those are really good Pumps also that come with that converter.
Quote:
Originally Posted by ranker
Since its a 24v < converter overvolting won't cut it. However if your want I believe you could run 2 converters in parallel and have volt range of 12-48v.
too much overvolting i'd say, as phelan said in another thread, we should already be happy with rd30 at 18v...
I really meant to say undervolt. I really just want to ditch this meanwell PSU because the only place I can mount it is up top near the mobo tray and that just makes it a piss ugly build. Will this thingamajig work with the RD-30? and allow me to undervolt it to 18v?Quote:
Originally Posted by Turtle 1
Quote from Performance-PC's website...Quote:
Originally Posted by ranker
"With the external adjustable DC voltage converters (12, 15, 18, 21 and 24 Volts) you may adapt the delivery rate of your pump to your own configuration. The 1500 litres which are achieved at the highest level satisfy even the most pretentious expectations."
Well, I guess the question is, can I get this separately somewhere else or purchase a comparable product. A small power brick like that is much nicer (its black too!) and easier to fit in my case.Quote:
Originally Posted by SiGfever
guys i just lost a tracer. The ram went bad on me today. DOE!
And no i didnt majorly overclock the ram. The highest voltage i gave her was 2.275v.
Anyhow DOE! how long does there rma take anyone? and do they do advance RMA?
Quote:
Originally Posted by NaeKuh
2.2 is already considered dangerous territory from my friends at EVGA. DDR2 RAM chips are designed for 1.8V according to JEDEC standards. EVGA techs tell me their stance is that 2.3 is the limit. However, would push more than 2.1v. Anything over that won't kill the stick out right, but will degrade it over a 3-6 month period.
blah... it says stock is 2.2.Quote:
Originally Posted by ranker
People in the memory forum are saying it needs a bit more because the LED's it has takes up voltage as well.
so i thought a nice number like 2.275 would be enough to keep it at top shape without the loss of power from the LED's
Well i'll call the RMA tommarrow. I honestly dont think i voided out the warrenty. Id hate to buy another set even tho there 149.99 right now at the egg.
There's been a huge fiasco lately with all enthusiast memory makers. Corsair, Crucial, OCZ have all tried to one up each other by supplying overclocked RAM to secure the enthusiasts dollars. RAM shouldn't have to be higher than 1.8V stock which is the reason why those three companies have been taking a toll on their bottom line. They're just binning memory chips after a small stress test. They found out too late that it takes 3 months to degrade most chips with even slight overvolting. You can see the fiasco in full effect on most motherboard forums (evga, asus from my own experience) across both C2D chipsets, the 680i and the 965.Quote:
Originally Posted by NaeKuh
I'd suggest you find the lowest amount of voltage it takes for you to pass an 8 hour stress test. My Corsair 8500 dominators were rated for 2.3 but I can run them at 1.9 just fine.
Quote:
Originally Posted by ranker
yeah thanks for the heads up ranker. next time i'll run them at 2.0v lol
2.6 volts FTW.. just kidding lol... I got wise and now I run everything at 1.8 volts.
on 2 good notes.Quote:
Originally Posted by IanY
1. there doing an rma for me.
2. my rma rep cindy sounds cute. :up:
#2 alone gets good customer service. :rofl:
what screws did you use to mount pa120.3 in front?
Black Oxide 6-32 1.75" machine screws.Quote:
Originally Posted by Grinch
ok thank you....*-)
Ack, didn't know if that was directed at me or Naekuh's machine. But I use those.Quote:
Originally Posted by Grinch
only difference in mine are brass instead of black oxide.Quote:
Originally Posted by ranker
Oh and its flat base, not rounded.
(Crucial is cross shipping me the bad tracer. My red Temp probe came bunk, but jab-tech offered to replace it for me free.)
Project will start again soon. I still need to think of a way to use the acrylic. I decided to forgo the front acrylic grill.