Intel Xeon 3060 First result! 56K soon to be DEATH!

Printable View

Show 100 post(s) from this thread on one page

02-08-2007, 07:22 AM
Pt1t

Quote:

Originally Posted by loc.o

With multi? I have 7x583 now unmodded board but i need vcore AND cooling..

585 with X6 But I dont know FSB max of this motherboard, it s a new one.

And i havent try other bios than 1004.
02-08-2007, 05:46 PM
erwinz

Quote:

Originally Posted by Pt1t

Soon with Good Vcore :) , Under cascade (-80°), i have 585 FSB max. And Maybe 600*9 under LN2.

very nice.. I will look forward for your results.. :)

:woot:
02-13-2007, 06:36 PM
fhpchris

I am very sad to say that I may have killed my xeon :(

I was having some freak things happen with my RD600, and it would only boot @ stock, sometimes even freezing in the bios @ stock...

Throw it in the Commando, no post. Code on the back was:

"CPU INIT" :*(
02-13-2007, 06:39 PM
dinos22

Quote:

Originally Posted by fhpchris

I am very sad to say that I may have killed my xeon :(

I was having some freak things happen with my RD600, and it would only boot @ stock, sometimes even freezing in the bios @ stock...

Throw it in the Commando, no post. Code on the back was:

"CPU INIT" :*(

they sometimes survive man

just give it a bit of a rest and try again....clean in give it a few kisses...hell it's valentines day you never know ............otherwise :(:(
02-13-2007, 06:44 PM
fhpchris

Quote:

Originally Posted by dinos22

they sometimes survive man

just give it a bit of a rest and try again....clean in give it a few kisses...hell it's valentines day you never know ............otherwise :(:(

I am pretty sure that it is dead :(

1.67v on water on a B chip might be pushing the envelope a little too hard , but I think this is a RD600 related failure reallly. I could not even reach what my AW9D would run, and my results kept getting worse and worse...
02-14-2007, 09:38 AM
Trike

Came here to seek some advice about my 3060.

My specs:
L629A780 3060 366x9@1.48v
P5b Deluxe
Tuniq tower 120
Corsair 620HX

I'm trying really hard to hit 3.6 and i've hit a wall already at 3.3ghz. I can only run 3.3ghz stable at 1.43V. 1.48 set in bios. With the side panel open, I'm running at ~60C Load ~50Idle. Reported in Coretemp/TAT. I can boot into windows at 3.6@1.55v but fails orthos immediately. Raising Vcore doesn't help in this case (up to 1.65v in bios). 3.4 wont run orthos for more than 2-3minutes. Min volt. required to boot into 3.4 was 1.45v raised as high as 1.55v but can't get it stable. I've remounted the Heatsink about 6 times now the past month, all temps were the same except one time when i put too little AS5 and idle temps were in the 60's.

This all points to a Heat related issue, Could I have gotten a bad chip? Ambient temps in the room is about 70F. Everyone else with A chips seems to be doing pretty well, even on air. My friend has the identical setup, ordered the same time and I helped him setup his machine, he idles and loads consistently 10C cooler than me. Just seems odd that our setup is that off. I know there are variables due to ambiet temps. That's the only difference I can see.

Just seeing what the guru's here to say. Any help is appreciated.

Thanks!
02-18-2007, 07:31 PM
fhpchris

http://www.sspmustang.com/OT/x3060/3...os-runlow2.JPG
is 1.35v ish real bad for priming 3600 mhz ?
02-18-2007, 09:59 PM
NeoRecon

I just got my 3060, L631B.... I'm excited to try some OCing with it. I finally got the entire system running nice and stable at all stock settings. The thing running a bit 'below' its suggest stock settings is my Memory. Any suggestions on where to start?
02-18-2007, 10:37 PM
momomo6789

4004 thats also prime stable 1.65v i did i suicide run @ 4.15 for fun :) 7638a563 off zzf :)

http://i13.photobucket.com/albums/a299/momomo6789/4.jpg

http://i13.photobucket.com/albums/a2...o6789/pi32.jpg
02-22-2007, 07:14 AM
MakenValborg

HI guys,
Soon I'll get one of these, I hope mine will rock as yours :D
02-22-2007, 07:33 AM
Avman

see sig
02-22-2007, 07:35 AM
MakenValborg

Quote:

Originally Posted by Avman

see sig

Awesome :eek:
02-24-2007, 07:54 AM
ted3

Got a 3060 yeasterday, L631 B115. CPU-Z says 1.113 volts, and no doubt it like low voltages. Temperatures are very high even on 1.4v, below 1.5 seems to be enough for 3.73GHz or more. Great chip, im happy :woot: , now i just need to do something to handle those temps... Lapping and maybe order a Tower 120 (using TR XP-120 now).
02-25-2007, 04:36 AM
sofarfrome

Quote:

Originally Posted by ted3

Got a 3060 yeasterday, L631 B115. CPU-Z says 1.113 volts, and no doubt it like low voltages. Temperatures are very high even on 1.4v, below 1.5 seems to be enough for 3.73GHz or more. Great chip, im happy :woot: , now i just need to do something to handle those temps... Lapping and maybe order a Tower 120 (using TR XP-120 now).

I just got mine (same stepping as yours) running along fine at 3.6GHZ with 1.325vcore. But I had to lap the core yesterday before I could get the temps down. I am at 36C idle and 48C load. Before I was at 47C idle and 60C load. Once I started lapping I looked at the IHS and couldn't believe how concave this thing was. Intel sucks for putting these $325 chips out there with such horrible IHS's.
02-25-2007, 05:11 AM
momomo6789

:toast: :toast: :toast: :banana: :banana: :banana:
02-25-2007, 01:35 PM
sixfootduo

Hey, question, I was just able to buy one of these Xeon chips for $240 shipped.

Will it work with a ASUS P5N32-E SLI Plus LGA 775 NVIDIA nForce 650i SLI ATX Intel Motherboard - Retail board ?

Or do I need a bios update or is it impossible due to hardware / chipset?

Thanks for the help. I can maybe cancel this order.

I really would like to have this answered asap.

Thanks in advance!
02-25-2007, 03:25 PM
ted3

Quote:

Originally Posted by sofarfrome

I just got mine (same stepping as yours) running along fine at 3.6GHZ with 1.325vcore. But I had to lap the core yesterday before I could get the temps down. I am at 36C idle and 48C load. Before I was at 47C idle and 60C load. Once I started lapping I looked at the IHS and couldn't believe how concave this thing was. Intel sucks for putting these $325 chips out there with such horrible IHS's.

Nice volts. I can run mine below 1.4v at 3.6GHz, but then it will reboot when running TAT at 100% both cores. 1.4125v (1.365v reported by IDU @ full load) is the lowest TAT stable. Prime/Orthos is no problem so maybe i shouldnt care about TAT. Gonna lap it when i get a Bad Axe 2 next week and then see how high it can go.
02-28-2007, 08:03 AM
Firlando

Hmmm just finished read whole thread a minute ago. but dont see any 3D mark 2006 CPU score, just wondering the score. what is the basic different between conroe with this xeon chip? anyone could explain it?

thanks n best regards :)
02-28-2007, 08:39 AM
fhpchris

They are the same.
02-28-2007, 08:44 PM
Firlando

OMG, so it's only differ from the name only? there's no advantage using Xeon, in my country Xeon more expensive about US$5-US$10 than conroe 6600.

thanks fhchris for the answer :-)
02-28-2007, 08:58 PM
fhpchris

Quote:

Originally Posted by Firlando

OMG, so it's only differ from the name only? there's no advantage using Xeon, in my country Xeon more expensive about US$5-US$10 than conroe 6600.

thanks fhchris for the answer :-)

Xeons are better quality than a normal Conroe E6x00.

I would pay the extra 10$ and get the xeon :)
02-28-2007, 09:33 PM
dinos22

so are they all good or are there some duds as well

i want o change my E6600ES B1
02-28-2007, 09:53 PM
fhpchris

Quote:

Originally Posted by dinos22

so are they all good or are there some duds as well

i want o change my E6600ES B1

I have bought three Xeon 3060s. Each one primed 3900mhz on water.

Two were from newegg. Last from another retailer. All sealed.

FreeCableguy owns my old L629A780 :)

My last Xeon could prime 3600 @ 1.35v easily, with 7+ hours of 3903 walling the board.

IMHO, YOU HAVE A GOOD CHANCE AT GETTING A BETTER X3060 THAN X6800!

Afireinside's L630A Xeon, "handpicked" by newegg ;D
470*9 = 4230 3d01 on WATER?
http://sean.nickfire.com/core2redux/71.5k-3d01.JPG
http://www.xtremesystems.org/forums/...d.php?t=134205

My X6800 could not even pass 1m @ that speed.
02-28-2007, 10:55 PM
Pete@X

Quote:

Originally Posted by dinos22

so are they all good or are there some duds as well

i want o change my E6600ES B1

Just be carefull what you get, as here are also 763xyyy :eek: Xeons around - so far i have seen 3050 and 3060´s with that FPO/Batch. They do NOT clock that well :( , they stay very cool (stock-idle- ~ 20to25c) but that´s it. Try to get a L630 or L631 and you are good to go ;) for 3.6GHz between 1.3V and 1.35V. Best L631B115 i had so far could do 3.7€1.35V, 3.8@1.40V :clap:
02-28-2007, 11:27 PM
GrimReaper

Quote:

Originally Posted by Pete@X

Just be carefull what you get, as here are also 763xyyy :eek: Xeons around - so far i have seen 3050 and 3060´s with that FPO/Batch. They do NOT clock that well :( , they stay very cool (stock-idle- ~ 20to25c) but that´s it. Try to get a L630 or L631 and you are good to go ;) for 3.6GHz between 1.3V and 1.35V. Best L631B115 i had so far could do 3.7€1.35V, 3.8@1.40V :clap:

Pete an L630 or L631 B or A? :D I saw an L631B locally should I pick it up? :stick:
02-28-2007, 11:51 PM
Pete@X

Quote:

Originally Posted by GrimReaper

Pete an L630 or L631 B or A? :D I saw an L631B locally should I pick it up? :stick:

Hi Grim ...

if it`s an L631B115 - get it ! The worst i have seen so far could do 3.6 ~ 1.4VCore - do the maths :-). There are serveral coresteppings around (so far i could locate 35634256 / 2L636070 / 2L636051 / 35633208) - so cores from week 33 to 36, but they clock nearly all the same. It`s just a question what you need for 3.6GHz - 1.3V or a bit more :toast:
03-01-2007, 12:11 AM
GrimReaper

thanks pete!

I will see whats the exact stepping and check:D
03-01-2007, 04:56 AM
Snyxxx

Just bought 2- 3070s Retail Box from Newegg. They were both L632B. Testing now on a P5N32-E Plus.
03-01-2007, 06:56 AM
fhpchris

Quote:

Originally Posted by Snyxxx

Just bought 2- 3070s Retail Box from Newegg. They were both L632B. Testing now on a P5N32-E Plus.

Let me know your results :)
03-01-2007, 04:55 PM
parodius4

1 Attachment(s)

Hi, I received my 3060 yesterday, it's a 638A.
First thing I noticed was that this CPU had the worst heatspreader I've ever seen. If Intel selects these CPUs then certainly not by their heatspreaders. I applied a thin layer of thermal-grease and pressed it onto a plane glass-panel and the impression was only a thin line from the very edge of the hs. So I tried a slightly thicker layer of grease, just as much as I'd use when actually putting on my watercooler - same result. So I had to start grinding and polishing even before putting it to use for the first time, just hoping it wasn't a defect one. On the picture you can see the thin margin of copper where the sandpaper had taken away the coated surface of the hs; w/out grinding, this copper-line would've been the only contact.

As for overclocking I can definitely say that this CPU is better than my 6600 (which isn't the best), but it's far from beeing a monster-overclocker. At default speed I can use less voltage and it runs much cooler than the 6600, furthermore I can clock it much higher at stock voltage (3,3GHz), but until now I couldn't manage to get it to 3,6GHz Orthos small FFTs stable at 1,44V.
But I think I have to check my mobo a little better to be sure about that. It surely has massive droop. Maybe a serious overclocker could get this CPU to 3,8GHz or more. Until now 3,5GHz at 1,44V (1,5V in BIOS) is the maximum to be small FFT stable.
BTW Orthos blend test would pass w/ much higher frequencies, so I think for sole CPU stability check small FFTs are better.

Will post if further testing gains better results.
03-06-2007, 01:41 AM
GasPipeJimmy

I got my Xeon 3060 from Newegg last week, but my membership here was not approved until today, so here goes.
Sorry, no pics yet, but I did copy this down off the top of the processor.

2.40GHZ/4M/1066/06
Intel Xeon
3060 SL9TZ PHILIPPINES

7638A563

Pack Date was Feb. 1, 2007.

Intel's site says this is a B2 stepping
03-06-2007, 03:26 AM
vega22

L631B115 here, from Germany. VID=1.225v. All Right.
My xeon came with a small whitish mark near a corner, in the bottom. All the 3060 has it?
03-06-2007, 10:20 PM
parodius4

Hey Vega, where did you buy your one?
03-06-2007, 10:52 PM
Kunaak

L631B from newegg.

quick tests.
1.35 volts, stock voltage - 3600 mhz stable.
1.45 volts, top windows speed 4060 mhz.

1.45 volts top stable speed 3.97 ghz.

temps are horrible though.
the IHS has a really bad bowing to it, not concave like usual.

cooling, just plain water.
CPU isnt mine, my friend came by cause his P5WDH new from newegg, doesnt work. so he wanted to test his ram and CPU here.
seems like a great CPU to me.
03-07-2007, 02:17 AM
vega22

Quote:

Hey Vega, where did you buy your one?

http://www.alternate.de/html/index.html

Quote:

1.35 volts, stock voltage - 3600 mhz stable.
1.45 volts, top windows speed 4060 mhz.

1.35 stock? That is too high for xeon. Which is your VID?
VID in coretemp
03-07-2007, 07:44 AM
Kunaak

1.35 volts is normal.

look at the box.
03-07-2007, 08:48 AM
vega22

In the box says 1.35 Max, in my Bios says default 1.325, and really the VID is 1.225, and my motherboard really is sending 1.20v (possibly 0.025 Vdrop) to mic:VCORE
03-08-2007, 04:07 PM
mucker

Rolled the dice with Newegg and looks like I lucked out.....

L631B115 :hump:

Ordered the 6th, received today, 8th.....
03-08-2007, 11:48 PM
Primoz78

I have a Xeon 3060 L631B115 pretested to run on 413FSB with 1.388V (in windows) but I have several problems get my system stable I have ran dual prime small ffts withouth problems for 9h+ but blend test it gave me an error within 1-2 minutes...could it be an incompatibility issue with my ram?...all my components are in my sig...

I had a E6600 L624AXXX before and never had this problems...

Regards,
Primoz
03-10-2007, 04:25 PM
Firlando

Quote:

Originally Posted by Pete@X

Just be carefull what you get, as here are also 763xyyy :eek: Xeons around - so far i have seen 3050 and 3060´s with that FPO/Batch. They do NOT clock that well :( , they stay very cool (stock-idle- ~ 20to25c) but that´s it. Try to get a L630 or L631 and you are good to go ;) for 3.6GHz between 1.3V and 1.35V. Best L631B115 i had so far could do 3.7€1.35V, 3.8@1.40V :clap:

just got Xeon 3060 six days ago, I've found it's L631B115 :banana: I need 1.42v to run @3.7Ghz but unable to run higher. I use P6N SLI Platinum, it can post 3.8ghz@1.42v but still freeze in windows, I try variate voltage up to 1.54v but still unable to hit 3.8ghz stable :confused: .
03-10-2007, 04:29 PM
phelan1777

Where are you guys ordering from?

I'm going to order one from the Egg.......wish me luck?
03-10-2007, 04:33 PM
Firlando

Quote:

Originally Posted by phelan1777

Where are you guys ordering from?

I got it from local INTEL distribution in indonesia (Terra Computer System)

here some picture taken six days ago.

http://i179.photobucket.com/albums/w...o/DSC01324.jpg

http://i179.photobucket.com/albums/w.../batchXeon.jpg
03-10-2007, 05:25 PM
ChaosMinionX

Any new emergences in the Xeon world for super chips and weeks? Im thinking about buying a new one soon
03-10-2007, 05:45 PM
phelan1777

Just how does one get a hand picked chip from NEwegg?

I really would like to know what stepping I am getting.
03-10-2007, 07:36 PM
ChaosMinionX

Quote:

Originally Posted by phelan1777

Just how does one get a hand picked chip from NEwegg?

I really would like to know what stepping I am getting.

Know somebody that works for them? or in the warehouse
03-13-2007, 09:48 PM
Hassan

Just received a L643G009 from Newegg, it runs about the same temps on air as my L631B115 on water, and so far is priming at 3.7 but at 1.52 volts
03-14-2007, 02:45 AM
phelan1777

Quote:

Originally Posted by Hassan

Just received a L643G009 from Newegg, it runs about the same temps on air as my L631B115 on water, and so far is priming at 3.7 but at 1.52 volts

I am ordering one today, I MIGHT get lucky...........

Hassan, did it ship from the NJ warehouse?
03-14-2007, 04:02 AM
Vulcan

I just got two 3060s from newegg. Incredible temps on both of them. They both are L643G009's

Seriously, the idle temp is about 25C, load of about 45C.

Impressive chips.
03-14-2007, 08:57 AM
Ten

Quote:

Originally Posted by Vulcan

I just got two 3060s from newegg. Incredible temps on both of them. They both are L643G009's

Seriously, the idle temp is about 25C, load of about 45C.

Impressive chips.

in what speed are you running and cooling?
03-14-2007, 11:12 AM
Vulcan

Quote:

Originally Posted by Ten

in what speed are you running and cooling?

Thats stock speed/voltage with an ultra-120 and generic white thermal paste. I will reseat with AS5 it once I settle in on the best clocking chip.
03-14-2007, 11:16 AM
phelan1777

I so should order one but I am indecisive
03-14-2007, 01:19 PM
Vulcan

I'm beginning to wonder how accurate these core temps are on my 3060's.

Now that I've started pushing them, the socket temp actually ends up being higher than core temp. Something seems a little off.
03-14-2007, 01:57 PM
Hassan

Quote:

Originally Posted by Vulcan

I'm beginning to wonder how accurate these core temps are on my 3060's.

Now that I've started pushing them, the socket temp actually ends up being higher than core temp. Something seems a little off.

yes the socket temp is off, mine jumps from 50 to 60 to 95 in a matter of seconds on a P5-B then back to 50 and 60 while TAT and coretemp remain rock steady during orthos
03-14-2007, 04:56 PM
Vulcan

Quote:

Originally Posted by Hassan

yes the socket temp is off, mine jumps from 50 to 60 to 95 in a matter of seconds on a P5-B then back to 50 and 60 while TAT and coretemp remain rock steady during orthos

I don't know, my socket temp has always been pretty reliable. With my 6300 it was consistently started out about 10C lower than core temp, and then crept up to about 5C lower.
03-15-2007, 11:10 AM
hawtrawkr

ordered a 3060 from newegg yesterday and got a l631f561 will have to wait until monday to play with it as they dicked around with sending the motherboard out.
03-16-2007, 03:32 PM
trans am

Quote:

Originally Posted by hawtrawkr

ordered a 3060 from newegg yesterday and got a l631f561 will have to wait until monday to play with it as they dicked around with sending the motherboard out.

I ordered one on Monday and it just arrived from newegg. Exact same chip you have:

XEON 3060
L631F561

I'm testing in a P5B dlx right now at 400*9
it failed orthos immediately @ 1.35vcore

my vdroop on p5b is terrible so I might need to do the pencil mod tonight./ brb

EDIT

okay, I just set 1.45vcore in bios. (idle= is 1.416) (load =1.3840v!!!!) I watched the vcore drop in AI suite right before my eyes and Orthos failed immediately after the drop..

0.034 total vdroop
0.066 total vdrop (small fft)
this sux. I'm not doing anymore testing until I do the pencil mod.

brb
03-16-2007, 05:28 PM
hawtrawkr

good luck with the pencil mod. Im thinking about going to a friends house to throw this chip in just to see what it can do. have one with a asus p5w dh deluxe and one with a aw9d-max. trying to just have the patience till my new mobo comes on monday though........
03-16-2007, 06:24 PM
trans am

Quote:

Originally Posted by hawtrawkr

good luck with the pencil mod. Im thinking about going to a friends house to throw this chip in just to see what it can do. have one with a asus p5w dh deluxe and one with a aw9d-max. trying to just have the patience till my new mobo comes on monday though........

Pencil mod got the 3.6 stable.

Before pencil mod

bios 1.45
idle 1.416
load 1.3840

after
------------------

bios 1.45
idle 1.4240
load 1.4160

temps are awesome 27c idle (apogee block)
411*9 was a fail in orthos at the same vcore
gotta kick it up some more

I have a 2nd shot at 4ghz. another 3060 on monday. :toast: lemme know how yours goes.
03-16-2007, 08:45 PM
fhpchris

no price cuts on the Xeons guys, grab them up while they are hot :)
03-17-2007, 05:50 AM
hawtrawkr

Quote:

Originally Posted by trans am

I have a 2nd shot at 4ghz. another 3060 on monday. :toast: lemme know how yours goes.

glad to hear the pencil mod helped out with it. Ill definantly update the thread with my results come monday night.

Quote:

Originally Posted by fhpchris

no price cuts on the Xeons guys, grab them up while they are hot :)

which will undoubtedly make them a whole lot less popular when compared to the 6600 a 10$ diffrence is one thing but if they arent going to drop the price on the xeons theres going to be a whole lot more than a 10$ diffrence between the 2. :(
03-17-2007, 09:51 AM
fhpchris

Quote:

Originally Posted by hawtrawkr

which will undoubtedly make them a whole lot less popular when compared to the 6600 a 10$ diffrence is one thing but if they arent going to drop the price on the xeons theres going to be a whole lot more than a 10$ diffrence between the 2. :(

Mabye we will just have to buy other kinds of UP Xeons :)

http://aycu36.webshots.com/image/106...2253151_fs.jpg

http://aycu02.webshots.com/image/122...6294418_rs.jpg
03-17-2007, 05:17 PM
Norz

1 Attachment(s)

Xeon 3060 + Abit QuadGT 1066strap + Crucial 10th Anni sub4ghz spi1M:D

My best so far, this chip does over 4300mhz on water, love the Xeons.
03-19-2007, 11:56 AM
trans am

Quote:

Originally Posted by Norz

Xeon 3060 + Abit QuadGT 1066strap + Crucial 10th Anni sub4ghz spi1M:D

My best so far, this chip does over 4300mhz on water, love the Xeons.

Wow! Very nice ram clock/cpu clock combination!

:toast:

I just received my 2nd Xeon from Newegg. This one shipped from jersey warehouse. L643G009

I am going to compare it to my other one. I hope this is better. That topped out at 3.6ghz. 3.7 was unstable no matter what voltage. we'll see...wish me luck.
03-19-2007, 12:34 PM
hawtrawkr

Quote:

Originally Posted by trans am

I just received my 2nd Xeon from Newegg. This one shipped from jersey warehouse. L643G009

I am going to compare it to my other one. I hope this is better. That topped out at 3.6ghz. 3.7 was unstable no matter what voltage. we'll see...wish me luck.

best of luck with the new xeon. Ill be testing my l631f tonight if it doesnt perform well I wont be getting another cpu until the end of april most likely :mad:
03-19-2007, 02:42 PM
trans am

Quote:

Originally Posted by hawtrawkr

best of luck with the new xeon. Ill be testing my l631f tonight if it doesnt perform well I wont be getting another cpu until the end of april most likely :mad:

I installed the L643G009..

Not good. I didn't change any settings and windows couldn't even complete loading. tried higher vcore 1.5-1.6 and made it into windows but orthos would stop after 1 minute or less!!! :(

Lets just say that chip isn't in my rig anymore.

Back to the L631F. Good luck :)
03-19-2007, 02:58 PM
safan80

I'm looking into getting one of these but I don't want a week 40+ Xeon my week 42 Conroe can't do 3.6Ghz stable. has anyone ordered this cpu within the last 8 days from the egg and still got a week 31?
07-12-2007, 07:14 PM
caligula

Time to revive this thread.
Just tested two 3060's, L629. Mobos used: pn5-e sli and g33m-ds2r, as coolers zalman cnps7700AlCu and TT SonicTower, both with arctic silver 5 correctly applied ;)
Although the coolers don't get really hot, coretemp and speedfan report horrible load temps (above 75 C) at around 3.2GHz so clocking them above 3.4 would inherently involve water.
As a matter of fact one of them would not go past 3.1GHz orthos stable on air no matter what.
I have another two chips as reference for the boards/coolers, a 6400 which primes stable at 3.2GHz and a 4300 perfectly stable at 3.3GHz, both at default vcore.
And a big "no,no" to the witty grandmas around here, xeons are not binned for lower voltages or temps, just rebranded 6600's.
07-12-2007, 09:51 PM
Ten

I got a xeon 3060 some timeago. L644F011 as i seen that new cpu:s don't oc so good i can't complain on this with P5K DLX as many said need a littlebit higher vocre:)
http://img503.imageshack.us/img503/5...thosqk2.th.jpg
08-03-2007, 01:36 AM
Charley2020

I like to get my xeon 3060 running OC in a Server Environment. In Fact 24/7.

Till now it runs rockstable (24h Orthos Blent) at 3375Mhz with 1,35V under Water at about 54 Degree while under load.

What are your OC rockstable Settings which you can recommend for 24/7 ?

My xeon runs a little hot. Guess it is the Apogee GT :(
09-10-2007, 09:01 PM
uneverno

Hi guys,

I've had my 3060 for a while now. I bought it from http://www.priceguidenetwork.com/ and asked Phil for a specific batch # (Batch # L709A523).

Here are some of my results:

3600MHz at 1.28Vcore

http://i235.photobucket.com/albums/e.../36001.28V.jpg

3770MHZ @ 1.32Vcore

http://i235.photobucket.com/albums/e...kVolts3770.jpg

3907MHz @ 1.4Vcore

http://i235.photobucket.com/albums/e...s/30603907.jpg

4104MHz at 1.45Vcore.

http://i235.photobucket.com/albums/e...s/30604104.jpg

4153MHz @ 1.5Vcore

http://i235.photobucket.com/albums/e...s/30604153.jpg

One hell of a CPU, I run it day to day at 3770 @ 1.32Vcore. :D
09-10-2007, 09:24 PM
louie101086

damn xeon chips seem great has anybody used new one that have sse4 because i was wondering if that would boost performance
09-10-2007, 09:32 PM
uneverno

Quote:

Originally Posted by louie101086

damn xeon chips seem great has anybody used new one that have sse4 because i was wondering if that would boost performance

SSE4 is for 45nm Penryn and up processors. Not released yet.
09-10-2007, 10:01 PM
louie101086

nope correction its on xeon x3220

http://www.newegg.com/Product/Produc...82E16819117127
09-10-2007, 10:10 PM
uneverno

Quote:

Originally Posted by louie101086

nope correction its on xeon x3220

http://www.newegg.com/Product/Produc...82E16819117127

No current Intel cpu's have SSE4 period. Penryn only!

http://download.intel.com/technology...ions-paper.pdf
09-10-2007, 10:37 PM
louie101086

say if it did what would that mean for performance and ur link didnt work

Show 100 post(s) from this thread on one page

All times are GMT -8. The time now is 09:51 PM.

XtremeSystems