Printable View
:D Thats cool.Quote:
Originally Posted by SNiiPE_DoGG
I also thought I should add that my chip does have a stuck sensor. I think that Im stable at 445x9 with 1.328 vcc full load 6 hours prime (so far). I might tighten some timings and run IBT soon. I may have to play around with lineload enabled. I was hoping for 475x9 for 24/7.
I've been benching a Q9450 and P5E3 Premium since July 2008 not wanting to jump to i7 right away. I just pulled the trigger and bought a Q9650 + P5Q3 Deluxe WiFi @N board, G.Skill 2x2GB 1600Mhz 4GBPI Black and eVGA GTX285 from Newegg yesterday. I bought the P5Q3 Deluxe because my current media server is running an Intel DG33FB/E6850 which I was going to throw my Q9450 in when the Q9650 arrives but as far as Intels site goes the DG33FB does not support my Q9450. It says the board supports QUADS up to 1066FSB.
So, I will bench the hell out of the Q9650 on P5E3 Premium and P5Q3 Deluxe and will then keep the best performing board in my main rig and put the other with the Q9450 in my media server.
I should have all the parts by Tuesday and will start posting results in this thread. I have all kinds of memory to test: two sets of G.Skill 2x1GB 1600Mhz HZ D9GTS, Mushkin 2x2GB 1600Mhz D9GTS and just purchased a set of G.Skill 2x2GB 1600Mhz 4GBPI Black.
I have had great success with my Q9450/P5E3 Premium overclocking it up to 515FSB, 512FSB benchable all with Vcore at or below 1.45v. I have heard alot of people stating P45 alows higher FSB for 45nm Quads so thats why I went with that Board.
Got my new Q9650 the other day, batch is L826A965.
First try is this, its 100% P95 stable for 12 hours, I just didnt save a screenshot. I might can get it lower than 1.264 with some additional tweaking just havent done alot since ive only had it for a day
http://i270.photobucket.com/albums/jj93/itslogz/ijh.jpg
Validated @ 4.6, just set a random voltage to boot up.
http://valid.canardpc.com/show_oc.php?id=508274
http://i270.photobucket.com/albums/jj93/itslogz/46.jpg
Posted @ 4.8 but wouldnt boot windows, used the same voltages i did for 4.6 but was too tired to try anymore. Ill post again if I can get validated @ 4.8 (i should be able to) everything in BIOS is on auto except for MCH core/Dram/Vcore and LLC and I only used 1.300 NB for 4.6ghz and 1.472v.
For a quick initial overclock that looks pretty good. I'm loving the temps and vcore compared to my Q9450. I'm sure with some more testing/tweaking you can raise that overclock and lower that vcore a little.
Any Vantage, 3D06 and SuperPI?
Here is my 834A957 1.25vid 9650 on 3DM06 and 32meg Pi at 4400mhz at 1.45v on water. :cool:
NICE OC there flesheatinvirus
QX9650 on water 4.4/4.5GHZ
Thank You Sir, looks like you are doing just fine as well. That is a killer score for a 3870 X2.
Quote:
Originally Posted by flesheatinvirus
I was thinking the same thing, keep up the good work:clap: Can't wait to start benching my Q9650/GTX285:rolleyes:
Quote:
Originally Posted by sigi
Thanks for the info guys! :)Quote:
Originally Posted by emertX
Mine hit 4050mhz with ease, had no time to really test the CPU though, but looking good :cool:
I buy a Q9650 to:D I hit 500+ whit a QX6850 an Q6700:rolleyes: on this ASUS P5Q Deluxe,on watercooling.
so it will be fun to see what a Q9650 can, because it is not so hot:p:
temp is to high whit QX9650@4.6GHZ /1.635v
Here is another run of 3DM06 and Cinebench R10 at 4446mhz at 1.45v, this chip is a keeper. My new 24/7 test speed is 4400 at 1.4v cpu, 333strap, .680v CPU GTL 0/2, .680v CPU GTL 1/3, 1.50v PLL, 1.40vFSB Term, 1.40vNB,.680vNB GTL, 2.38vDDR, 1.20vSB, Load-line enabled, both spectrums disabled, both clock skews on auto and running in performance mode. I am very happy with the results so far and this Teamgroup simply cranks on this P5Q deluxe, it can do 600 4-4-4-12 no problem at 2.45v. For someone not ready to jump to a i7 build this is certainly the chip to get. Deachus you are going to love that combo of hardware and good luck to you.:up: http://service.futuremark.com/compare?3dm06=10027709
well here is 506x8.5 ddr1012 1:1 pl8 cas 4-4-4-10 stabe 4hrs+ prime blend.and my full bios settings.
http://i44.tinypic.com/szvjly.jpg
http://i39.tinypic.com/aaeot0.jpg
Code:EP45 UD3P******
Q9650 506 X 8.5 4301MHz
Robust Graphics Booster.........................[ Auto ]
CPU Clock Ratio.................................[ 8.5 ]
Fine CPU Clock Ratio............................[ 0 ]
CPU Frequency 4.31GHz...........................[ 506 x 8.5 ]
******Clock Chip Control******
CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 506 ]
PCI Express Frequency (Mhz).....................[ 100 ]
C.I.A 2 [Disabled]
******Advanced Clock Control******
CPU Clock Drive.................................[ 1000mv ]
PCI Express Clock Drive.........................[ 1000mv ]
CPU Clock Skew..................................[ 0ps ]
MCH Clock Skew..................................[ 50ps ]
******DRAM Performance Control******
Performance Enhance [Standard]
Extreme Memory Profile (XMP)....................[ Disabled ]
(G) MCH Frequency Latch.........................[ Auto ]
System Memory Multipler.........................[ 2.00D ]
Memory Frequency 1066...........................[ 1012 ]
DRAM Timing Selectable..........................[ Manual ]
CAS Latency Time................................[ 4 ]
tRCD............................................[ 4 ]
tRP.............................................[ 4 ]
tRAS............................................[ 10 ]
******Advanced Timing Control******
tRRD............................................[ Auto ]
tWTR............................................[ Auto ]
tWR.............................................[ Auto ]
tRFC............................................[ Auto ]
tRTP............................................[ Auto ]
Command Rate (cmd)..............................[ Auto ]
******Channel A Timing Settings******
Static tRead Value [ 7 ] ................[ 8 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 7 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel A Driving Settings******
Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Channel B Timing Settings******
Static tRead Value [ 6 ] ................[ 8 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 7 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel B Driving Settings******
Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Motherboard Voltage Control******
Load-Line Calibration [Enabled]
CPU Vcore [ 1.23750 ]...................[ 1.41250 ]
CPU Termination [ 1.20 ]...................[ 1.42 ]
CPU PLL [ 1.50 ]...................[ 1.57 ]
CPU Reference [ 0.766 ]...................[ 0.924 ]
MCH Core [1.1 ]...................[ 1.42 ]
MCH Reference [0.760 ]...................[ 0.939 ]
MCH/DRAM Refernce [0.900 ]...................[ Normal ]
ICH I/O [1.500 ]...................[ Normal ]
ICH Core [1.100 ]...................[ Normal ]
DRAM Voltage [1.800 ]...................[ 2.32 ]
DRAM Termination [0.900 ]...................[ Normal ]
Channel A Ref [0.900 ]...................[ Normal ]
Channel B Ref [0.900 ]...................[ Normal ]
******Advanced BIOS Features******
CPU Multithreading..............................[ Disabled ]
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]
Quote:
Originally Posted by flesheatinvirus
WOW that is a nice GTX280!
Nice work Radaja looks like another good chip.:clap: Systemviper that is a incredible speed for a 9650 what batch is that from?
I have tweaked and worked with my mobo and this cpu and the final 24/7 oc that I am comfortable with on this mobo is 4.05GHz. Do you think these chips have enough still to squeeze out of them to pick up a sub $200 P45 mobo and drop in and see how it does?
Of course it does. You only need a $100 UD3P :up:Quote:
Originally Posted by ElAguila
I was looking at the asus p5q, BIOSTAR TForce TP45D2-A7, or the foxcon p45a. Any recommendation among these or something else? I haven't used MSI for some time now because of a major issue in the past. I don't mind using gigabyte either. But also keep in mind that it has to be friendly with my 8GB of ram that is in my sig. I have decided since I am seeing very little difference between 1 4870 X2 and a quadfire of 2 4870 X2 cards, I am going to sell one off and buy a P45 with it. I am not looking to move to core i7 until much later in the year.
Hey radaja does this look familiar?
Didn't mean to steal them, just messing around.
http://i40.tinypic.com/m7t3sz.jpg
one more, thanks again radaja
http://i41.tinypic.com/123y078.jpg
I recommend the Gigabyte ud3p p45; look through this thread a little and even check out the ud3p thread on here. It really does wonders with the 9650. Amazing really, especially for $100 or so.:up:Quote:
Originally Posted by ElAguila
But; i really see some nice results from the Asus-guys too,
FleshEatingVirus and deachus and some others have posted some impressive overclocks on asus boards also.
Yep. I realized after posting that you had recommended that mobo. Any issues with that motherboard and the GSkill ram in my sig?
Check out some of RaDaja's posts; that man has been doing wonders with multiple GsKillz stix for a while on a Ud3PQuote:
Originally Posted by ElAguila
I mean how does 506 fsb @4,4,4,10 with 4x2gb gskills stable sound?
Nice chip - can the older boards (P35) run it OK? Can I expect a good OC on my P5KC?
Having trouble getting above 4.050Ghz with mine. Bought it during the 500$ price tag days so it's an early one. I can run 4.050Ghz but dropping my multi to 8 & even 6 at 500fsb doesn't work. Is it a CPU issue? like not getting enough voltages (1.344v for 4Ghz stable) or a Mobo issue (Maximus II Formula)
I've tried all the way up to 1.4vcore, 1.6pll, 1.4 fsbt, 1.7v NB (using DDR2 1000 = solid - no errors @ 500 or 1000 by Memtest86+)
Using EK supreme n other custom H20 cooling parts...
What are the highest safe voltages to try ?
Both my 9550 and 9650 did pretty good on my P5K Prem with just over 4G solid so it should be fine. 529th your Nb and Pll are too high drop the Pll to 1.5 and NB to around 1.4 for starters. What board?