very nice NewBeetle.. :D
Printable View
very nice NewBeetle.. :D
Getting lower:D .... sucks that I cant use setfsb cos the abit prog goes in 1 fsb increments.... Gautam, you need to pick up one of these:) ....
12.xx
http://ocidb.com/albums/userpics/10062/3591.JPG
Sorry for my tardiness. I went insane and lost a week of my life. I was trying to get .001 sec quicker than this but it is not to happen. PF-512mb to 1023, maxmem from 640mb to 570mb. Waza sizes and delays. Spi in different drives. Affinity-RT etc. It was kinda fun in a sordid way now that I'm done.
http://img164.imageshack.us/img164/7294/1300000cj5.jpg
I have conceeded and will move on, and update the thread. Time for 11.xx then P35.
abit IP35 Pro is looking good.. :)Quote:
Originally Posted by luihed
:woot:
14.xx.xx Entry
http://img167.imageshack.us/img167/5...5memsetuf5.png
i need to learn copywazza, maxmem & eram to get a better score :)
tnx
15.xx.xx Entry
http://img214.imageshack.us/img214/3...smemsetww1.png
tnx
DJ, man I can't compete here yet. :D alaws mems. Need better mems for low clock challenges.
coop, there is no way in hell you can stop there. I don't care if its a been a week. :D What board is that?
Thanks NewBeetle for the loan of your awesome E6700 L633A549 #2;)
P5K#2
Air Cooling
Team PC2-6400 CL4
1.36Vcore, 1.579Vnb, 2.542Vdimm
FSB550@boot
Maxmem=600, Copy Waza
http://premium1.uploadit.org/fredyam...5s-3300GHz.gif
@Gautam, thanks 4 the encouragement. It is my QuadGT. I will give it a go now and then but I am out of ideas.
Okay, have you ever tried a maxmem below 500? I think your page file is too large as well. I set 48-96. I like using large copy waza sizes (>5GB). Copy to the benching partition and then from it instead of just once as well.
This is gonna be close.... Just did 9m56s @ 5040mhz, Im gonna try 9.xx @ less than 5ghz....my stupid board is acting up again though :(...
I see your LN2 session is going well. :p:
i lil better now... yesterday it was a nightmare and I didnt get to do anything.... but it looks like Im topping out at around 5100mhz.....
This board is acting up big time even today.... everytime I have a bad setting I have to start from low clocks ( below 400fsb) and make my way up... FFS, im doing 16m runs ar 3800mhz righ now at -120c lol....
I've gotten used to working up. Though I usually start around 4800-5000. You might be using too much or too little vcore.
congrats! nice to see another E6600 join that sub10 club. best of luck in the sub5GHz/sub10m quest, looks like the new pot is working out rather nicely for you :up:Quote:
Originally Posted by luihed
despite the frustration...don't forget to have fun ;)
16.xx.xx Entry :D
http://img455.imageshack.us/img455/3...ymemsetsa8.png
Im getting used to it... the bios in this board gets screwy as in thiers corruption in the bios screen, and I cant get rid of it at times..... anyways I couldnt get another run to finish so I guess this is what I got.... Im happy with the time its just frustrating sometimes when you have a promising start and then nothing happens... this run was done in the first hour, didnt finish another run after at both higher and lower speed :(
9.xx entry...
http://www3.telus.net/luis99/5040.JPG
don't feel bad.. :)Quote:
Originally Posted by luihed
btw bro.. your on top of the 9.xxx :D
congratz.. :)
:woot:
sounds exactly like my last 32M session with the QuadGT and dry ice...best run in the first 30 mins of a 5 hour session.Quote:
Originally Posted by luihed
remember though, you are one of a very select few, as in a handful that is missing fingers, with a sub 10min E6600...big congrats on that :up: :up:
Thanks man... Yeah its been like this for me the last couple of times, get your best run early on and then nothing for the next few hours lol.... The thing is at this PP it puts me at 5006mhz, I had so much room to tighten up my timings and also the run above wasnt even at realtime priority.... Under 5gs was so doable and I was right there, thats what made it frustrating.... I didnt even get a decent 1M run or even a decent screenie lol.... But #12 overall and #2 E6600 at HWbot is very alright for me:D not to mention #1 9.xx in the toughest and the best low clock challenged in the world hehe..:)Quote:
Originally Posted by 3oh6
If it wasnt for this thread I wouldnt have put so much time to learn spi32m, I still suck compare to you guys but Ive learned so much:)
You did a great job bro. I haven't even bothered to try 32M yet on LN2. Props to you for jumping straight into it.
Thanks bro... I was practising on this run here to keep the temp in a 5c range which was alot harder than I thought... I totally give kingpin a whole new kind of respect cos he does it with 3 pots ......
yup i have high regards for 3Dmark LN2 benchers.. :) they are one of a kind..Quote:
Originally Posted by luihed
I tinhk their "pouring skills" are on the top.. :D
btw congratz again luihed.. :)
My entry was abysmal, 16m 57sec @3150Mhz. I'm guessing due to RAM latency and the 2Mb cache on my E6300. Anyway, thought i'd post it anyway.
Specs are in the signature, copied for anyone with sigs off:
Intel Core 2 Duo E6300 (3.15Ghz, 1.36v) | Scythe Ninja Plus Rev.B + Arctic Cooling AF12025
2x1Gb GeiL PC6400 5-5-5-18 2.1v
Gigabyte 965P-DS3 F11 BIOS
2x 250Gb SATA2 16Mb Cache
NEC ND3550A DVDRW
ATI X1600XT 256Mb
Interestingly my temps when loading both cores hit 65'C. Should i make a thread on this?
Anyway, screenie is below.
http://img296.imageshack.us/img296/7...allengehb7.jpg