Printable View
You can run 2 instances of OCCT
http://www.xtremesystems.org/forums/...highlight=occt
Using BT stable at 7x480= 3.36 atm :)Quote:
Originally Posted by PcCI2iminal
real vmch is 1.42 for +.1 or 1.62 for +.3
Got chipset container today, in a few days I hope dice action for both cpu and chipset :D
Here is a pic of dual SP32M at 3.4Ghz, not optimized really, just a quick run to see if it can pass or not
http://img220.imageshack.us/img220/1784/32m3400ma8.jpg
I so wish I would've gotten an E6300/E6400 instead of this dud E6600. :(
Why are you referring to the e6600 being a dud. From what I can tell the e6600 can do 400x 9 just fine. Are you just upset that you can't do more?Quote:
Originally Posted by Brahmzy
Thanks, but I think I've deactivated user accounts and I don't feel like reactivating them :) I think it's time the stress testing apps accounted for dual core by default.Quote:
Originally Posted by kiwi
hey, is this time ok without tweaks?
http://people.freenet.de/chris070719...erPi-32M-1.jpg
I can't get mine past 312FSB stable :(Quote:
Originally Posted by HeadShotWI
Chri$h, what's the rest of your specs on your setup. What kind of cooling, I'm assuming something above air.
kiwi what are your bios setting in the M.I.T screen, i cant seem to get anything past a 458 bios
my sys is cooled with water (CPU / NB / GPU) :)
Can your RAM do say 500?Quote:
Originally Posted by cliffy
See attached pics for bios. This is my daily setup :)
For 3.4Ghz, I had vmch + .3, vdimm +.6 and vcore 1.45V
What RAM you got?Quote:
Originally Posted by kiwi
Tkx Kiwi! Which memory are you using?
Placing on slots 1 and 3 or 2 and 4?
My RAM can clock to 950 with no extra volts (defaults to 2.1 at those speeds) been to scared to pump extra volts into the memory though. My RAM is rated up to 2.1 would +.4 be safe?
corsair 8000ul D9, yellow slots atm
so with RAM working fine at 950 are you able to boot and prime 475fsb mem multiplier 2x? It appears there are cases popping up where RAM can clock higher then the board will allow and extra volts don't seem to helpQuote:
Originally Posted by cliffy
I wanted to take the RAM out of the Equation so i reduced the FSB and up the RAM multiplier to get the RAM to 950. Since tried only one stick of RAM and changed from red to yellow slots, still no joy if i go 1Mhz over FSB458 the system will come out of bios power off and revert to stock Ghz
Is there any difference between the red and yellow slots?
Im using micron D9.
Quote:
Originally Posted by Brahmzy
It has to be a BIOS setting somewhere. I can't recall any Conroe clocking that low.
exact same problem i'm having. So this suggests the problem isn't the RAM and the board has problems with these bus speeds. Thoughts?Quote:
Originally Posted by cliffy
I don't think it's the chip because i did the same test as you with high mem multiplier and low fsb except i also used 6x multi on my E6300. With 6x multi i hit the same FSB limit so i don't think it's the chip maxing out.
Can anyone give me their opinion of this G.Skill memory for a E6400 on a GA-965P-DS3 ? I'm looking for good budget RAM.
ds3 pr0n
http://ferry.lghosting.nl/fotos :D
I can boot much higher, but these speeds are dual-Prime stable for 8 hours so that's what I'm going to use:
http://valid.x86-secret.com/show_oc?id=109664
http://www.damontech.net/aldamon3150.jpg
Can I flash bios through a USB-memory on DS3? Because I don’t have floppy driver, and I would like to flash bios to the newest version before I install any OS.
Gigabyte uses qflash and you can only load bios via a floppy. Either scrounge a floppy from an older computer or install os and use gigabyte @bios...
Yes, @BIOS off the installation CD works great. There is no need for a floppy :)Quote:
Originally Posted by vsamaco