Yeah yeah yeah, I will catch up to you eva2000!
Printable View
Yeah yeah yeah, I will catch up to you eva2000!
got a little 3d01 update:)
and i just ran through nature test with 1ghz on the mem :D (look screenshot)
have to try and run 1ghz all through the test in the weekend:)
44514
SIOUX, do you run every test at same speed?? - I run some tests at 20-30 mhz @ cpu faster than others...
Car low at 30 mhz more than lobby high... :|
i ran DL-CL-CH-DH with 3355mhz, and LH-N with 3345Quote:
Originally Posted by M.Beier
Hey Dynasty, any luck with that yet?Quote:
Originally Posted by Dynasty
Yeah, is there any way we can flash the BIOS, or do somet,do get rid of the 2d/3d clocks?
I assume all the problems with overclocking these cards with the software availaity atm, is due to the 2d/3d thing, and why Macci clocked his XT fine?
Quote:
Originally Posted by Hicks
Becourse macci´s card was a press sample card, with a different BIOS:)
kill off atismart and the other ati service (forgot its name - ati hotkey poller?), it fixes the coldbug issue and might force the card into just 2d or just 3d mode as well.. unsure about that though.
@ GHZ, nothing yet. :cool:
Quote:
Originally Posted by STEvil
It's exactly what i have try do, but with a stange result: i can use the 3D clock for OC with the Overclocker tool with or without disable this service, ( so overdrive work in CCC).
but when i disable the service, the 3D clock work allways for OC and the 2D clock don't give me any gain.. problem i can't increase the voltage, cause ATI-Tool do this for the 2Dclock.. I have try increase the 2D clock, the result of bench is exactly the same i have with the 3d clock at stock... I must have miss something.. ( I use Overclocker tool X1K, ATI-Tool 25.10b.)
Problem, after 722Mhz on core i need increase voltage.
And what is the symptom ( on display) of the cold bug?
What i use is:
- ATItool 1.24b9
- OC utility
- Cat 5.11
Disable ATI hotkey poller AND ATI smart in services and reboot. Use atitool for voltage adjustments only, dont use it for OC. Set your clocks in 2D tab in OC utility. Make sure that if you change core in the utility you also set mem again. After setting core (and mem) in the 2D tab check speeds in atitool to make sure its set.
thanks, i have use all other version and Cat 5.12
is your Oc utility look like this?http://img356.imageshack.us/img356/4...nstitre5gn.jpg
Sry, i have use SLI and Nvidia since my 9700pro...
need to knock out ati????.exe... my original post is incorrect ;)
The new RivaTuner does work nicely for monitoring...
Core Voltage
Core Clock
Memory Clock
Voltage Regulator Current (Amp)
No need for configuration. Just install it. Clocks do not work though. I tried even with the ATI Services disabled and it still resets the clocks back to the 2D when entering 3D for some reason.
Ok i have see what the problem reading the post of Riva by UGP.
I was not set the voltage of clock enough high, by default it's 1.3V for 2D and it jump to 1.4V when entering 3D... ATI tool report 1.275V, i have forget set the voltage higher for clock it ... so it have launch at 1.275V the bench, so crash or artefact.. he he!!!.
I have see the mosffet is around 46°C, i was thinking pehraps use the ALphacool watercool, its use separate cooler for each memory with 3/5mm tubing and a distributor, what do you think is it good too adition the mosffets (voltage regulator)? or there's no issue known when OC with this.
for the power regulators, take a cheap heatsink, use dremel...Quote:
Originally Posted by Lane-k
ok, thanks,..
It seems this X1800XT like high voltage on memory i was having "Freeze" during first 3D'05bench when the memory is at more of 819Mhz, after increase the voltage of memory, test pass.
Edit:
I haveone ask about the A read in Riva tuner, normally it's 8.18, after OC and during bench, i see it jump at more of 20A...
Tell me it's not taken on the 12V rails fully.!!??? Is this can be the thing can give me crash during bench?.. I have 40A on 2x 12V rails, but the 3700+ is a lot OC and i have many thing using the 12V rails ( around 14Fans 120mm, on the radiators + case, leds etc...)
I ordered my DangerDen x18 WaterBlock and got the HeatBridge as well with it for the Power Regulators.Quote:
Originally Posted by Gnome
I cannot get core over 770 with OC-tool. It wil let me set it but both atitool and OC-tool will report 770 after its saved. Tried AQ03 and 3D but scores stay same as with 770 set. Mem clocks/volts dont make difference, tried several. Im using cat 5.12, atitool 025b9 and both services disabled. VPU recover is disabled in CCC as wel. Stock hsf and temps are fine (mid 60's load 770/1.475v). Will try diff atitool and cat later but I am curious if someone else has had simular prob.
everybody: try Ati tool beta 11. can be downloaded from Techpowerup.com
I´m now able to clock the card without disabling the services. there are some good corrections for x1800 cards:) the new ati tool swiches between 2d/3d clocks,and disables ati2evxx.
use driver 5.11 or 5.13. 5.12 doesnt seem to work.
thanks
does ATI Tool beta 11 still work if those services are already disabled ?Quote:
Originally Posted by SIOUX
Does the "Max Clock" part work on Beta 11? Also I assume that it will save voltage settings to profiles as well.
stock voltage for mem is 1.8v correct?
ATI Tool has 2v stock, I will bring it back to 1.8v.
stock mem volt is 2.097v or whatever ati tool says as X1800 oc tool displays mem volt incorrectly it is not 1.8v AFAIK