thanks :)Quote:
Originally Posted by andressergio
i wanna push it a little bit further... but i must change thermal compound under IHS ;)
Printable View
thanks :)Quote:
Originally Posted by andressergio
i wanna push it a little bit further... but i must change thermal compound under IHS ;)
careful i see ppl puting the CPU over a flat table and start cutting THATS NOT RIGHT you should grab CPU with your hands and cut corners and all there with your hands so its flexible and you dont hurt PCB, this is the best mode after 9 delid i didQuote:
Originally Posted by gravimag
What batch is it ?
mmm 5Ghz haswell not bad results :up:
Some run with MSI Mpower Max under WC:
SuperPI 32MB 5GHz 1.325Vcore 4c8t
http://img23.imageshack.us/img23/426...25ghz1325v.jpg
Wprimes 4.8GHz 1.235Vcore
http://img28.imageshack.us/img28/208...48ghz1223v.jpg
3dMark 06 4.8GHz 1.235Vcore
http://img824.imageshack.us/img824/5...48ghz1223v.jpg
BR
Nacho
give batch nacho! haha
and go coldddd
The batch number is L307B156, i try 5 of the same batch, and this is the only goodone Vivi.
guys, any idea what is the safe limit for CPU RING Voltage? i've just checked voltage measurement points and found out that with CPU ratio x46 and Uncore ratio x46/ 1.2Vcore CPU RING (auto) is at 1.344V!!! (default is 1.05V...)
CPU VRIN is at 1.744V so it didn't change much, but RING is just mad...
look at this madness over at hwbot's thread. i'm trying this batch tomorrow, our supplier has stock of this batch so im taking as many as i can
Quote:
Originally Posted by Alatar
congrats nacho that seems a great CPU !!!Quote:
Originally Posted by nacho_arroyo
Good luck Vivi :up:
Maybe in cinebench, the only benchmark where 4770k really shines.Quote:
Originally Posted by owikh84
maybe cauz its using the graphics on die ?Quote:
Originally Posted by LiquidReactor
I got batch L312B332 anyone have anything on this other than l0ud_sil3nc3Quote:
Originally Posted by Vivi
Any information for L312B334 ?
Quote:
Originally Posted by Phaseshift
From what I've seen, just about every L312B has been sorta meh. The only good chip I've seen so far has been from L0ud.Quote:
Originally Posted by Ziwro
RobQuote:
Originally Posted by Rob94hawk
with what u gonna cover the circuits on PCB near die to delid it ?
Nothing. Was going to do the vice method.Quote:
Originally Posted by andressergio
wich is ?Quote:
Originally Posted by Rob94hawk
http://www.youtube.com/watch?v=2jjxvY6Y-P4Quote:
Originally Posted by andressergio
Becareful with vttddr and vccin.
One proc dead. Two more to go, got a gaygay oc to test as need to check where the prob
is.
do you guys have speed step on?
Just did a quick super pi run on 32m
47x on 1.28v
will push for further when I get home from work.
using an h100i
i would never recomend that to anyone my friend and i also refeer to the circuits on the PCB u have to cover them to use liquid proQuote:
Originally Posted by Rob94hawk
I have NT-H1 and Liquid Pro on it's way. I may use NT-H1 on the die and LP on the lid to avoid any circuit issues.Quote:
Originally Posted by andressergio
As for the vice method IMO it seems less likely to damage the PCB than a razor.
not if you grab CPU on your hands most ppl put it over a flat surface and then push the razor and that how PCB is damaged...u need to grab always CPU on your hands so you curve it as needed i delided 9 chips with not a single mark on it lookQuote:
Originally Posted by Rob94hawk
http://www.xtremesystems.org/forums/...results/page29
Only @ 4.2 Ghz and core's hitting 80 on water! Yep. It needs to be delidded.
http://img.photobucket.com/albums/v2...psc40fb6a5.png