Project: Virgin Suicide - First Time - Lian Li P80

@shazza: Thanks shazza! I try to take it slow and be careful. Still I have made a few mistakes, not big ones and most could be fixed :)
Btw, your paint job on the Pearl looks great!

@eponymous: Thanks! Looking forward to more updates on your build :)

Quote:

---

Originally Posted by LogAn'sRun

builds coming along nicely!
In the heatsinks is actually a gas, so I hope you were'nt breathing in at the time. . .

---

Oh, is that gas dangerous? :eek:

Quote:

---

Originally Posted by CptDreadFlint

Haven't found a "proper" way to test RAM temps, but I am prone to ghetto rigging. I once stuck thermal sensors and read the temps off an old fan controller. Uncertain as to how accurate this method yields but I reasoned that it couldn't be that far off.

But great progress, Winston! Dig seeing another XS member outfitting the same board as me with success. :up:

---

Ty Cpt!
That would work to see how good the RC cool the memory when painted.
To bad I don't have any idea to get the original ram sink off :confused:

Got this reply from Corsair when I asked them how to remove the Dominator DDR3 heat sink:

Quote:

---

Originally Posted by Corsair Technical Support

We do not suggest removing the heatsinks on these modules are they are hard glued onto the IC chips. Pulling the heatsinks apart may pull the chips off as well.

---

I Have been away on vacation in Greece this weekend but hope to get some work done in the next few days =)
.
.
.
.

Happy news, after problems with removing the heat sink on the Corsair Dominator memory I found a solution :idea: I will keep the heat sink on and fasten the Arctic cooling RC heat sink on the original heat sink :D The only modification was removing the top fins.

Think it looks good even tho the I didn't get the original heat off. Another plus with this solution, the paint will not jeopardize the cooling as much :)


http://i36.tinypic.com/2v9ads5.jpg




http://i36.tinypic.com/e5jm9w.jpg




http://i35.tinypic.com/2vv17ps.jpg
Yesterday I soldered the three rad fans together in a parallel loop. Main cable will connect to one control on the the fan controller using the first fan RPM cable.
I will connect the second fan RPM cable the motherboard. This to configure BIOS to shut down computer if fans fail :wiggle:




http://i33.tinypic.com/33m5wti.jpg
The pump look pretty nice in white :p:




http://i36.tinypic.com/qy75fk.jpg
Have also done some fan led removal. Desoldered all leds from the four Lian Li 140mm front door fans. I wasn't so found of the the blue led light since I will use white light in the case :rolleyes:



Things to do next:
- Paint the last four Arctic Cooling RC mem sinks.
- Sleeve the remaining cables.
- Find a solution to fasten the ROG chip heat sink.
- Try the plexi top for the NB/SB block (got this a few days ago).
- Test out res holder.
- Increase the length of the feet or maybe buy the Lian Li wheels.
- Make a side window (haven't decided how to do this the best way :confused:
- Put all the stuff together :hammer:
.
.
.

Good Progress ... like that memory heatsink solution and the white pump. And, agree your build will look better without the blue LEDs on the fans.

Great progress and a very interesting build.

You've got a good eye for design, I'm actually getting a bit jealous over here, haha! :up:

Imo, go with the acetal top and white/black fans for the radiators, it can't get more classy!

Quote:

---

Originally Posted by shazza

Good Progress ... like that memory heatsink solution and the white pump. And, agree your build will look better without the blue LEDs on the fans.

---

Ty shazza, I'm happy I found a solution for the mem sink :) I don't really like the color scheme of the Rampage II Extreme. The white mem sink will take the eye away from the beige color of the memory slots :rolleyes:

Quote:

---

Originally Posted by Laine

Great progress and a very interesting build.
You've got a good eye for design, I'm actually getting a bit jealous over here, haha! :up:

Imo, go with the acetal top and white/black fans for the radiators, it can't get more classy!

---

Ty Laine! Your crystal clear build is an inspiration to this one. Really like your choice of case and the plexi water blocks with your motherboard look just awesome :up:

Looks SO awsome so far, the final build is going to be sweet =)

Absolutely stunning! Really like this!

subscribed looks awesome

Im not a fan of white, but this one is really nice.

Ah apoteket renat vatten Im using that too^^

Nice work Winston:up:

Thanks a lot for the nice comments guys! :)

---

So this is what happen after my last update:

I have started to mount the gear inside the case but I also made a simple hold down plate for the ROG chip :)

The problem when you use EK waterblocks NB/SB water block is that you don't get a way to fasten the heat sink for the ROG chip.

I made a simple plastic plate and drilled two holes to use as bracket to hold the heat sink in place.


http://i37.tinypic.com/x5cm82.jpg
Bracket was made from an old plastic 5.25" bay shield.




http://i38.tinypic.com/20f464m.jpg
Screws used is black M3 16mm and M3 nuts.
The screws closest to the NB/SB water block was too long and I had to use a rasp and wet dry sand paper to take them down to 12mm.




http://i38.tinypic.com/28bhggn.jpg
I hope the chips on the bottom of the ROG chip don't get hot since I placed the plastic bracket on top of them.
Placed some thermal adhesive tape between the plastic bracket and the chips, hopefully this will be enough :rolleyes:




http://i36.tinypic.com/8y71mv.jpg
The cable got some sleeve :D




http://i33.tinypic.com/2054a5e.jpg
Finished look :)
.
.
.
.
More pictures sooon :banana:

Well done man, neat and tidy. :)

nice ;)

How did you manage to remove those -arctic cooling- stickers on the ram coolers? I have a huuuge problem removing those, and i dont want to scratch them using like a knife or something simular.

Ty for the comments eponymous and aka_GK!

Quote:

---

Originally Posted by The Viking

How did you manage to remove those -arctic cooling- stickers on the ram coolers? I have a huuuge problem removing those, and i dont want to scratch them using like a knife or something simular.

---

Actually I didn't remove them :) Had also a lot of problem removing those and wrote to Corsair. They answered that they use some kind of thermal super glue and there is a big risk you pull the chip off if you try to remove them.

Check the post in the top of this page and the last few posts on previous page :)

Just the single white Arctic cooling RC came out looking awesome, Winston.
I'm willing to bet that all four would quadruple the awesomeness. Any shots of those or did I miss that somehow?

And an excellent idea on mounting the ROG. Been trying to figure out a slick way to do that myself. Great job, all around! :up:

Nice mod!

Now ROG users can follow suit with that mod, or something like that

Hello again :)
So I have started putting stuff together and trying some things out.

I wanted to ask what you guys think, should I use the shroud solo or should I put the grill on top of the shroud?

Think it look better without the grill but I'm not sure :confused:

Another option is to fasten the fans directly on the radiator and skip the shroud, but I don't have black screws for that option and I'm not sure I can get hold of any.

I also have to apologize for the bad lighting. Result, high graininess and bad focus :down: To eager to wait for daylight :rolleyes:


http://i34.tinypic.com/rshsp2.jpg
Some bubble plastic will not be there in the final build. The black screws holding the fans are also missing.



http://i34.tinypic.com/2upppu8.jpg
Shroud + grill.


I also know I don't use the shroud as intended. Unfortunately there isn't enough room to fasten the fans on top of the shroud.

Quote:

---

Originally Posted by CptDreadFlint

Just the single white Arctic cooling RC came out looking awesome, Winston.
I'm willing to bet that all four would quadruple the awesomeness. Any shots of those or did I miss that somehow?

And an excellent idea on mounting the ROG. Been trying to figure out a slick way to do that myself. Great job, all around! :up:

---

I really appreciate your kind words Cpt :)
Just posted a photo with all Arctic Cooling RC. To bad the photos sucks, will take some better photos in daylight :)

Quote:

---

Originally Posted by GregSG

Nice mod!
Now ROG users can follow suit with that mod, or something like that

---

Thanks Greg! :)

Ok!

This is me being stupid again. I didnt remember that i posted a simular question about removing the Arctic cooling RC stickers, on page 3. You clearly explained it there, and ill try that method ;)

Quote:

---

Originally Posted by The Viking

Ok!

This is me being stupid again. I didnt remember that i posted a simular question about removing the Arctic cooling RC stickers, on page 3. You clearly explained it there, and ill try that method ;)

---

If you want to keep them black and not scratch the surface you should apply acetone to the edges of the sticker. Let it solve for like 20 sec and apply some more. Do this a few times to loosen the glue from the sticker.

Also to mention, somehow the sticker is easier to remove in the middle. Try different positions on the long sides of the sticker until you find a place where you get it to loosen and then carefully bend it up :)

Cover the adhesive glue on the heat sink so it wont get in touch with the acetone. Think I used masking tape.

Hope this helps =)

Looking Good :up:

I actually like the shroud with the grill.... also just incase something larger were to fall of the fans the grill would at least stop it from messing up the fans.. my 2cents

The white sinks are looking sick, Winston! Dig the look it provides your overall build.
I like the cleaner look of the grillless (is that a word?) shrouds, but then again there is a look of linear symmetry inside the case and the grills on the shrouds complement them. IMO, you can't go wrong either way. :up:

Nice looking build there.

... => :)