u can tell me what is your BIOS version? :confused:Quote:
Originally Posted by dengyong
thanks.
Printable View
u can tell me what is your BIOS version? :confused:Quote:
Originally Posted by dengyong
thanks.
There's no way to tell of that screenshot im afraid?
Quote:
Originally Posted by k.b.san.um
P06
Can someone tell me how to determine my batch #?
Settings are:
BCLK 190
Multiplier 20x
CPU voltage: 1.2125
QPI/DRAM voltage: 1.2
DRAM Bus voltage: 1.6
Speedstep and turbo OFF
Running an ocz platinum 6gb 1600 set of RAM at 1520 @ 7-7-7-18 1T timings.
Passed 12 hours of prime95 blend temps capping around 78. Idles in the 38-41 range (sometimes lower). I can take a screenshot if required, although I just closed prime after leaving it on overnight.
Yeah, you have to look at the BOX the cpu came from, look at the FPO # batch. down in the left if I recall.
or you can look at the cpu itself, but seems kinda hard when its in the use :)
is running my Corsair Dominators 6gb 1600MHZ at 1203MHZ with 6-6-6-18 1T safe setting? 1.66v
your batch number is on the boxQuote:
Originally Posted by foolycooly
3 - Factory
8- Year (2008)
41- Week in year
A525 - Lot#
anyone have the same batch as mine?
I might be testing a 3838B554 next week. from a local shopQuote:
Originally Posted by Godmyster
Quote:
Originally Posted by foolycooly
Good batch. :D
dude did you test the other one you had at your house? Not the one we ran prime on that you were using when I was over this passing weekend.Quote:
Originally Posted by hlonipha
they should be the same right? just last number that changes...Quote:
Originally Posted by hlonipha
Yes I tested it under water and it did very good but not as good as the one I'm keeping. :DQuote:
Originally Posted by Chicken Patty
Is that yours in the pic or is it the batch like mine?
very good Mario. Your chip is very good bro. Have the temps improved on your CPU now that the thermal compound is more settled in?
CPU speed: 4.4Ghz
920D0
RAM timings: 7-8-7-20-1T
CPU Ratio: 21x
BCLK: 210
DRAM: 1683 mhz
UCLK: AUTO
QPI: AUTO
HT: On
PCIE freq: 101Mhz
LLC: on
CPU differential amplitude: 900mV
CPU clock skew: normal
CPU spread spectrum: disabled
PCIE clock skew: normal
PCIE spread spectrum: disabled
Everything else: Untouched
Voltages:
CPU Voltage: 1.384v (1.375 in BIOS)
PLL Voltage: 1.98v
QPI/DRAM core Voltage: 1.375v
DRAM Voltage: 1.66v
All other voltages: Untouched
Sorry it would be really difficult to remove my cpu waterblock and clean off the paste just to see the batch number!
The cpu cooler is a heatkillerv3 lt with mx2 paste, quad thermochill pa series rad, double feser rad but i also have my 5870, and entire board watercooled aswell.
Temps dont go above 80-85c.
10 and half hours prime stable (after 10 and half hours i decided to stop prime so it hasnt blue screened on prime on those settings)
at 4.2 ghz i had only rough settings in and they seemed to work fine, 8 hours prime stable until i turned it off
CPU speed: 4.2Ghz
920D0
RAM timings: 6-7-6-18-1T
CPU Ratio: 21x
BCLK: 200
DRAM: 1600 mhz
UCLK: AUTO
QPI: AUTO
HT: On
PCIE freq: 101Mhz
LLC: on
CPU differential amplitude: 900mV
CPU clock skew: normal
CPU spread spectrum: disabled
PCIE clock skew: normal
PCIE spread spectrum: disabled
Everything else: Untouched
Voltages:
CPU Voltage: 1.3v
PLL Voltage: 1.92v
QPI/DRAM core Voltage: 1.375v
DRAM Voltage: 1.66v
All other voltages: Untouched
hope this helps and is not redundant without a batch number! sorry again!!
dengyong,can you tell me what program/app is that in your SS?Quote:
Originally Posted by dengyong