try getting rid of one card first and try again
good luck m8 :)
Printable View
try getting rid of one card first and try again
good luck m8 :)
Just an update for you guys. Going strong, though not prime strong at 2.55 on my caazc. Running 255x10 on 9/10 divider. Does 32M PiMod loops of fract bench, CS:s Stress test and 3d01. No random errors, gonna try some long hours of CS tonight...maybe get up to 6?
http://i4.photobucket.com/albums/y132/Magnj/2550mhz.gif
my caa2c....
http://img105.echo.cx/img105/3523/spi9ln.th.jpg
http://img105.echo.cx/img105/6145/alucpu7na.th.jpg
http://valid.x86-secret.com/show_oc.php?id=22673
week 09...
under testes.. need more time .
Quote:
Originally Posted by ...:::MadDog:::
-27c with a SSOI chip and 1.7v+ ?
What kind of cooling? Evaptemp?
With my SD @ 1.5 I get -26c with -44c on evap.
Did you remove HS, -50c on evap, or is your MBM (or mine) off?
The ClawCastles are very hot, just like the FX55s. Strange to see such low core temp.
the secret is this prommy....
made by |Ricky|....
temps... -27 in the proc and -47 evap...
very nice..
Quote:
Originally Posted by ...:::MadDog:::
You must have a chip with perfect contact betwen HS and Core. With my SD the temp difference between evap and core is 18c, and thats with only 1.5v
1.7v SSOI vs. 1.5v 90nm DSL .. BIG difference there.
Whats is your evap temp load? And where and what do you use to measure evap temp?
Insane OC on that 3500+ :DQuote:
Originally Posted by Dani
But holy crap. 1.9v? They scale above 1.75-1.8v?
Never tried more than 1.8v on mine. Diddn´t think it would do any good.
Well... my stupidity/lazyness is the only one to blame. Need to do a rerun now. Best time I had was 26sec @ 3250Mhz .. If i can get close to 3350 I might improve my score.
load temps in msi neo 2....
http://img135.echo.cx/img135/4117/20011ox.th.jpg
to read the evap temps i use this..
http://img204.echo.cx/img204/1246/img00124cf.th.jpg
its near the evap...
edit: this prommy is very good in load... dont lose to much temp..
|Ricky| made it whit that purpouse.
Quote:
Originally Posted by ...:::MadDog:::
What kind of tool is that? If its not a Fluke, Uei or such I don´t trust it. I have a cheap (20$) thermometer here, and it claims that my evap holds below -50c load when my Uei DT200 reports -44c
Tuning a cooler for high heatload is no problem.. hit the appr right cap length, and overcharge it. Its perfect for high heatload, but when idle you get liquid returning to the compressor, and thats not good.
I charge according to heatload. If I up the vcore 0.1-0.15v I add more gass to make it hold the temp better.
Even with a perfectly tuned MachII -47c is near impossible (if not impossible) with the heatload of a 130nm SSOI chip @ 1.7+vcore.
Im a n00b when it comes to phase change, but a NL11F holding -47c with that chip @ 1.7+vcore sounds hard. Very hard.
Sure Rickey has xtreme skills with phase change.. but still the compressor has got limitations.
-26c core temp on a SSOI Claw sounds impossible with that cooler and vcore.
Im guessing the MSI is off. I have had several neo2´s my self, and none of them reported similar core temps. Generally MSI sucks at measuring temps.
But then again.. im AM total n00b when it comes to phase change :)
what is a safe voltage for me to run through my chip on box cooler and paste? and is CPU Z what i should go by or bios? im at 1.536 in CPUZ
in air i use 1.60v and AS ceramique...
http://www.xtremesystems.org/forums/...ad.php?t=63479
soon i will have a new termometer...
now i have a dfi.. but you will have a surprise :D
hug'z.
ps, i'm more noob'er then you :D ..
benches sonn
yea pretty sure 1.6 is ok. As long as temps are ok.
i have a CAA2C 0506 BPMW it ocs great(235*11 at stock vcore) but i am having trouble with the memory controller i am using geil ultrax based on BH-5 chips and i cant seem to get it to oc the mem sweet f all
has anyone else had experiance with this cpu and ocing the memory
glad to see you..vim aprender um bocado.Quote:
Originally Posted by ...:::MadDog:::
:D
wanna see that dfi results.. :p:
Quote:
Originally Posted by ultma
ANYONE
BH-5 does not like that board w/o a lot more juice. Most people use a booster or VDimm mod if they're using BH-5. Even then some people have probs with that board and BH-5... But for sure, added juive is nevessary.Quote:
Originally Posted by ultma
My CPU is fine with that memory; running 255 at 1.5-2-2-5 ( and had it even higher). I have either an 08, or 09. But I don't use the MSI with it, I use a VDimm modded Epox. For the MSI I use TCCD.
yeah....click on the DDR600 in my signature. ;)Quote:
has anyone else had experiance with this cpu and ocing the memory
Quote:
Originally Posted by serlv
yeah i used a ddr booster 3.6v was just trying to find out if it was the cpu or the mobo. it also hated TCCD at a any mem ratio not 1:1 so that was no bloody good to me either.
an Epox u recon which one is best 9NDA3+ or 9NPA+
I'm using a 9NDA3+ and real happy with it, my Clawhammer and BH-5. Running it 24/7, somewhere a bit above 2800 mHz and at 255 or so ( on a different machine, in a different room right now ). Using a bit over 3.4 V.
Modded, this board is a screamer.
edit - Best? I don't know. As far as A64 Epox(s), I only have experience with mine. But I'm real happy with it.
It actually runs a DC project I run, D2OL, stronger than my DFI Ultra D/ Venice 3800+, which clocks a little higher overall.
does it fit a xp-120, 2*512 plus a ocz ddr booster
i read somewhere the xp-120 blocks memslot 1
Umm, not sure. I am using a XP-90C.Quote:
Originally Posted by ultma
There is a largish thread around here somewhere, labelled "9NDA3+ Mods", or something like that. Perhaps if you skimmed through that you might see if people have it listed in their sig.
Ahh, just went to Thermalright's site, and that is what it says in the Compatibility List. "Cannot use DIMM 1".
Hey MadDog, what version bios are you using on your Neo2 board?Quote:
Originally Posted by ...:::MadDog:::
I'm getting a Clawhammer later this week to try in my Neo2.
i use 1.80 oficial bios.
for me its the best.
Thanks MadDog!
I can't wait to try the Clawhammer. It is a CAA2C 0507GPMW.
07 its a god week, but the neo2 and is 1.84 of vcore... its to low to this caa2c's...